[    0.000000] Linux version 2.6.24-8-generic (buildd@rothera) (gcc version 4.2.3 (Ubuntu 4.2.3-1ubuntu2)) #1 SMP Thu Feb 14 20:40:45 UTC 2008 (Ubuntu 2.6.24-8.14-generic)
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
[    0.000000]  BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000d2000 - 00000000000d4000 (reserved)
[    0.000000]  BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000005ff60000 (usable)
[    0.000000]  BIOS-e820: 000000005ff60000 - 000000005ff77000 (ACPI data)
[    0.000000]  BIOS-e820: 000000005ff77000 - 000000005ff79000 (ACPI NVS)
[    0.000000]  BIOS-e820: 000000005ff80000 - 0000000060000000 (reserved)
[    0.000000]  BIOS-e820: 00000000ff800000 - 0000000100000000 (reserved)
[    0.000000] 639MB HIGHMEM available.
[    0.000000] 896MB LOWMEM available.
[    0.000000] Entering add_active_range(0, 0, 393056) 0 entries of 256 used
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA             0 ->     4096
[    0.000000]   Normal       4096 ->   229376
[    0.000000]   HighMem    229376 ->   393056
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0:        0 ->   393056
[    0.000000] On node 0 totalpages: 393056
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 4064 pages, LIFO batch:0
[    0.000000]   Normal zone: 1760 pages used for memmap
[    0.000000]   Normal zone: 223520 pages, LIFO batch:31
[    0.000000]   HighMem zone: 1278 pages used for memmap
[    0.000000]   HighMem zone: 162402 pages, LIFO batch:31
[    0.000000]   Movable zone: 0 pages used for memmap
[    0.000000] DMI present.
[    0.000000] ACPI: RSDP signature @ 0xC00F6D70 checksum 0
[    0.000000] ACPI: RSDP 000F6D70, 0024 (r2 IBM   )
[    0.000000] ACPI: XSDT 5FF6A6BD, 004C (r1 IBM    TP-1R        3210  LTP        0)
[    0.000000] ACPI: FACP 5FF6A800, 00F4 (r3 IBM    TP-1R        3210 IBM         1)
[    0.000000] ACPI Warning (tbfadt-0442): Optional field "Gpe1Block" has zero address or length: 000000000000102C/0 [20070126]
[    0.000000] ACPI: DSDT 5FF6A9E7, C4E5 (r1 IBM    TP-1R        3210 MSFT  100000E)
[    0.000000] ACPI: FACS 5FF78000, 0040
[    0.000000] ACPI: SSDT 5FF6A9B4, 0033 (r1 IBM    TP-1R        3210 MSFT  100000E)
[    0.000000] ACPI: ECDT 5FF76ECC, 0052 (r1 IBM    TP-1R        3210 IBM         1)
[    0.000000] ACPI: TCPA 5FF76F1E, 0032 (r1 IBM    TP-1R        3210 PTL         1)
[    0.000000] ACPI: BOOT 5FF76FD8, 0028 (r1 IBM    TP-1R        3210  LTP        1)
[    0.000000] ACPI: PM-Timer IO Port: 0x1008
[    0.000000] Allocating PCI resources starting at 70000000 (gap: 60000000:9f800000)
[    0.000000] swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
[    0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000d2000
[    0.000000] swsusp: Registered nosave memory region: 00000000000d2000 - 00000000000d4000
[    0.000000] swsusp: Registered nosave memory region: 00000000000d4000 - 00000000000dc000
[    0.000000] swsusp: Registered nosave memory region: 00000000000dc000 - 0000000000100000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 389986
[    0.000000] Kernel command line: root=UUID=d8a9bb6c-9eeb-4ebd-8b2f-69957663476c ro quiet nosplash
[    0.000000] Local APIC disabled by BIOS -- you can enable it with "lapic"
[    0.000000] mapped APIC to ffffb000 (01c11000)
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[    0.000000] Detected 1594.876 MHz processor.
[   11.054861] Console: colour VGA+ 80x25
[   11.054866] console [tty0] enabled
[   11.055533] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[   11.056227] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[   11.149559] Memory: 1546296k/1572224k available (2161k kernel code, 24800k reserved, 997k data, 364k init, 654720k highmem)
[   11.149568] virtual kernel memory layout:
[   11.149570]     fixmap  : 0xfff4b000 - 0xfffff000   ( 720 kB)
[   11.149571]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[   11.149572]     vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
[   11.149574]     lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
[   11.149575]       .init : 0xc041b000 - 0xc0476000   ( 364 kB)
[   11.149576]       .data : 0xc031c5ed - 0xc0415dc4   ( 997 kB)
[   11.149578]       .text : 0xc0100000 - 0xc031c5ed   (2161 kB)
[   11.149582] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[   11.149652] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
[   11.229674] Calibrating delay using timer specific routine.. 3224.41 BogoMIPS (lpj=6448832)
[   11.229724] Security Framework initialized
[   11.229739] SELinux:  Disabled at boot.
[   11.229763] AppArmor: AppArmor initialized
[   11.229768] Failure registering capabilities with primary security module.
[   11.229780] Mount-cache hash table entries: 512
[   11.229982] CPU: After generic identify, caps: a7e9f9bf 00000000 00000000 00000000 00000180 00000000 00000000 00000000
[   11.230000] CPU: L1 I cache: 32K, L1 D cache: 32K
[   11.230003] CPU: L2 cache: 1024K
[   11.230008] CPU: After all inits, caps: a7e9f9bf 00000000 00000000 00002040 00000180 00000000 00000000 00000000
[   11.230020] Compat vDSO mapped to ffffe000.
[   11.230038] Checking 'hlt' instruction... OK.
[   11.246131] SMP alternatives: switching to UP code
[   11.248305] Freeing SMP alternatives: 11k freed
[   11.248450] Early unpacking initramfs... done
[   11.658119] ACPI: Core revision 20070126
[   11.658246] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[   11.662921] ACPI: setting ELCR to 0200 (from 0800)
[   11.672947] CPU0: Intel(R) Pentium(R) M processor 1600MHz stepping 05
[   11.672954] SMP motherboard not detected.
[   11.672956] Local APIC not detected. Using dummy APIC emulation.
[   11.673005] Brought up 1 CPUs
[   11.673028] CPU0 attaching sched-domain:
[   11.673031]  domain 0: span 01
[   11.673033]   groups: 01
[   11.673232] net_namespace: 64 bytes
[   11.673241] Booting paravirtualized kernel on bare hardware
[   11.673895] Time: 15:52:39  Date: 02/21/08
[   11.673950] NET: Registered protocol family 16
[   11.674154] EISA bus registered
[   11.674166] ACPI: bus type pci registered
[   11.674487] PCI: PCI BIOS revision 2.10 entry at 0xfd8d6, last bus=8
[   11.674490] PCI: Using configuration type 1
[   11.674492] Setting up standard PCI resources
[   11.679141] ACPI: EC: EC description table is found, configuring boot EC
[   11.684866] ACPI: EC: non-query interrupt received, switching to interrupt mode
[   11.688060] ACPI: Interpreter enabled
[   11.688064] ACPI: (supports S0 S3 S4 S5)
[   11.688078] ACPI: Using PIC for interrupt routing
[   11.694979] ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
[   11.694983] ACPI: EC: driver started in poll mode
[   11.695130] ACPI: PCI Root Bridge [PCI0] (0000:00)
[   11.695515] PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
[   11.695519] PCI quirk: region 1180-11bf claimed by ICH4 GPIO
[   11.696043] PCI: Transparent bridge - 0000:00:1e.0
[   11.696144] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[   11.696203] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
[   11.696228] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
[   11.700081] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11)
[   11.700276] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11)
[   11.700469] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11)
[   11.700661] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11)
[   11.700837] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
[   11.701013] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
[   11.701190] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
[   11.701383] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11)
[   11.701552] ACPI: EC: non-query interrupt received, switching to interrupt mode
[   11.701651] ACPI: Power Resource [PUBS] (on)
[   11.701697] Linux Plug and Play Support v0.97 (c) Adam Belay
[   11.701729] pnp: PnP ACPI init
[   11.701737] ACPI: bus type pnp registered
[   11.702834] pnpacpi: exceeded the max number of mem resources: 12
[   11.705251] pnp: PnP ACPI: found 13 devices
[   11.705253] ACPI: ACPI bus type pnp unregistered
[   11.705257] PnPBIOS: Disabled by ACPI PNP
[   11.705488] PCI: Using ACPI for IRQ routing
[   11.705491] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[   11.721673] NET: Registered protocol family 8
[   11.721675] NET: Registered protocol family 20
[   11.721748] AppArmor: AppArmor Filesystem Enabled
[   11.725642] Time: tsc clocksource has been installed.
[   11.733679] system 00:00: iomem range 0x0-0x9ffff could not be reserved
[   11.733683] system 00:00: iomem range 0xc0000-0xc3fff could not be reserved
[   11.733686] system 00:00: iomem range 0xc4000-0xc7fff could not be reserved
[   11.733689] system 00:00: iomem range 0xc8000-0xcbfff could not be reserved
[   11.733692] system 00:00: iomem range 0xcc000-0xcffff could not be reserved
[   11.733695] system 00:00: iomem range 0xd0000-0xd3fff could not be reserved
[   11.733699] system 00:00: iomem range 0x0-0x0 could not be reserved
[   11.733702] system 00:00: iomem range 0x0-0x0 could not be reserved
[   11.733705] system 00:00: iomem range 0xdc000-0xdffff has been reserved
[   11.733708] system 00:00: iomem range 0xe0000-0xe3fff could not be reserved
[   11.733711] system 00:00: iomem range 0xe4000-0xe7fff could not be reserved
[   11.733714] system 00:00: iomem range 0xe8000-0xebfff could not be reserved
[   11.733723] system 00:02: ioport range 0x1000-0x107f has been reserved
[   11.733726] system 00:02: ioport range 0x1180-0x11bf has been reserved
[   11.733729] system 00:02: ioport range 0x15e0-0x15ef has been reserved
[   11.733732] system 00:02: ioport range 0x1600-0x162f has been reserved
[   11.733735] system 00:02: ioport range 0x1632-0x167f has been reserved
[   11.733738] system 00:02: ioport range 0x1630-0x1631 has been reserved
[   11.764200] PCI: Bridge: 0000:00:01.0
[   11.764203]   IO window: 3000-3fff
[   11.764207]   MEM window: c0100000-c01fffff
[   11.764210]   PREFETCH window: e0000000-e7ffffff
[   11.764218] PCI: Bus 3, cardbus bridge: 0000:02:00.0
[   11.764221]   IO window: 00004000-000040ff
[   11.764225]   IO window: 00004400-000044ff
[   11.764229]   PREFETCH window: e8000000-ebffffff
[   11.764233]   MEM window: c4000000-c7ffffff
[   11.764237] PCI: Bus 7, cardbus bridge: 0000:02:00.1
[   11.764239]   IO window: 00004800-000048ff
[   11.764243]   IO window: 00004c00-00004cff
[   11.764246]   PREFETCH window: ec000000-efffffff
[   11.764250]   MEM window: c8000000-cbffffff
[   11.764254] PCI: Bridge: 0000:00:1e.0
[   11.764257]   IO window: 4000-8fff
[   11.764262]   MEM window: c0200000-cfffffff
[   11.764266]   PREFETCH window: e8000000-efffffff
[   11.764281] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[   11.764648] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
[   11.764651] PCI: setting IRQ 11 as level-triggered
[   11.764655] ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[   11.764996] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
[   11.764999] ACPI: PCI Interrupt 0000:02:00.1[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
[   11.765015] NET: Registered protocol family 2
[   11.801728] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[   11.802056] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[   11.803681] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[   11.804823] TCP: Hash tables configured (established 131072 bind 65536)
[   11.804827] TCP reno registered
[   11.813870] checking if image is initramfs... it is
[   12.265626] Switched to high resolution mode on CPU 0
[   12.609685] Freeing initrd memory: 7590k freed
[   12.609933] Simple Boot Flag at 0x35 set to 0x1
[   12.610313] audit: initializing netlink socket (disabled)
[   12.610333] audit(1203609160.460:1): initialized
[   12.610564] highmem bounce pool size: 64 pages
[   12.612784] VFS: Disk quotas dquot_6.5.1
[   12.612881] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[   12.613051] io scheduler noop registered
[   12.613054] io scheduler anticipatory registered
[   12.613057] io scheduler deadline registered
[   12.613074] io scheduler cfq registered (default)
[   12.613148] Boot video device is 0000:01:00.0
[   12.613492] isapnp: Scanning for PnP cards...
[   12.970032] isapnp: No Plug & Play device found
[   13.003676] Real Time Clock Driver v1.12ac
[   13.003793] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[   13.004863] serial 00:0a: activated
[   13.005135] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a NS16550A
[   13.005327] ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
[   13.005337] ACPI: PCI interrupt for device 0000:00:1f.6 disabled
[   13.006024] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[   13.006103] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[   13.006215] PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
[   13.012795] serio: i8042 KBD port at 0x60,0x64 irq 1
[   13.012800] serio: i8042 AUX port at 0x60,0x64 irq 12
[   13.013599] mice: PS/2 mouse device common for all mice
[   13.013724] EISA: Probing bus 0 at eisa.0
[   13.013730] Cannot allocate resource for EISA slot 1
[   13.013734] Cannot allocate resource for EISA slot 2
[   13.013736] Cannot allocate resource for EISA slot 3
[   13.013739] Cannot allocate resource for EISA slot 4
[   13.013741] Cannot allocate resource for EISA slot 5
[   13.013743] Cannot allocate resource for EISA slot 6
[   13.013745] Cannot allocate resource for EISA slot 7
[   13.013748] Cannot allocate resource for EISA slot 8
[   13.013750] EISA: Detected 0 cards.
[   13.013754] cpuidle: using governor ladder
[   13.013756] cpuidle: using governor menu
[   13.013868] NET: Registered protocol family 1
[   13.013901] Using IPI No-Shortcut mode
[   13.013938] registered taskstats version 1
[   13.014060]   Magic number: 12:482:892
[   13.014146]   hash matches device ptyy2
[   13.014206]   hash matches device 0000:00:1f.5
[   13.014489] Freeing unused kernel memory: 364k freed
[   13.017445] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[   13.215014] fuse init (API version 7.9)
[   13.229033] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[   13.229041] ACPI: Processor [CPU] (supports 8 throttling states)
[   13.231676] ACPI: Thermal Zone [THM0] (47 C)
[   13.986029] usbcore: registered new interface driver usbfs
[   13.986061] usbcore: registered new interface driver hub
[   14.001374] usbcore: registered new device driver usb
[   14.013364] USB Universal Host Controller Interface driver v3.0
[   14.013448] ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[   14.013461] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[   14.013466] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[   14.013944] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[   14.013971] uhci_hcd 0000:00:1d.0: irq 11, io base 0x00001800
[   14.014146] usb usb1: configuration #1 chosen from 1 choice
[   14.014174] hub 1-0:1.0: USB hub found
[   14.014180] hub 1-0:1.0: 2 ports detected
[   14.047486] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
[   14.047491] Copyright (c) 1999-2006 Intel Corporation.
[   14.117868] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
[   14.117875] ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
[   14.117888] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[   14.117892] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[   14.117920] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[   14.117945] uhci_hcd 0000:00:1d.1: irq 11, io base 0x00001820
[   14.118077] usb usb2: configuration #1 chosen from 1 choice
[   14.118105] hub 2-0:1.0: USB hub found
[   14.118111] hub 2-0:1.0: 2 ports detected
[   14.137608] SCSI subsystem initialized
[   14.191081] libata version 3.00 loaded.
[   14.221858] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
[   14.221864] ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
[   14.221877] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[   14.221882] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[   14.221909] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[   14.221934] uhci_hcd 0000:00:1d.2: irq 11, io base 0x00001840
[   14.222075] usb usb3: configuration #1 chosen from 1 choice
[   14.222102] hub 3-0:1.0: USB hub found
[   14.222108] hub 3-0:1.0: 2 ports detected
[   14.305357] Floppy drive(s): fd0 is 1.44M
[   14.326789] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
[   14.326795] ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11
[   14.326811] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[   14.326816] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[   14.326854] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
[   14.330781] ehci_hcd 0000:00:1d.7: debug port 1
[   14.330788] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[   14.330798] ehci_hcd 0000:00:1d.7: irq 11, io mem 0xc0000000
[   14.335166] FDC 0 is a National Semiconductor PC87306
[   14.345278] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[   14.345425] usb usb4: configuration #1 chosen from 1 choice
[   14.345453] hub 4-0:1.0: USB hub found
[   14.345460] hub 4-0:1.0: 6 ports detected
[   14.449535] ACPI: PCI Interrupt 0000:02:01.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[   14.705914] e1000: 0000:02:01.0: e1000_probe: (PCI:33MHz:32-bit) 00:09:6b:53:18:25
[   14.742420] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
[   14.742572] ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
[   14.765288] ssb: Sonics Silicon Backplane found on PCI device 0000:02:02.0
[   14.765395] ata_piix 0000:00:1f.1: version 2.12
[   14.765412] PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
[   14.765421] ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
[   14.765463] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[   14.766339] scsi0 : ata_piix
[   14.766889] scsi1 : ata_piix
[   14.767869] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1860 irq 14
[   14.767872] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1868 irq 15
[   14.931396] ata1.00: ATA-8: SAMSUNG HM160HC, LQ100-10, max UDMA/100
[   14.931402] ata1.00: 312581808 sectors, multi 16: LBA48 
[   14.947264] ata1.00: configured for UDMA/100
[   15.421809] ata2.00: ATAPI: UJDA745 DVD/CDRW, 1.02, max UDMA/33
[   15.593728] ata2.00: configured for UDMA/33
[   15.593886] scsi 0:0:0:0: Direct-Access     ATA      SAMSUNG HM160HC  LQ10 PQ: 0 ANSI: 5
[   15.596006] scsi 1:0:0:0: CD-ROM            MATSHITA UJDA745 DVD/CDRW 1.02 PQ: 0 ANSI: 5
[   15.617468] Driver 'sd' needs updating - please use bus_type methods
[   15.617575] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[   15.617590] sd 0:0:0:0: [sda] Write Protect is off
[   15.617592] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   15.617610] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   15.617663] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[   15.617673] sd 0:0:0:0: [sda] Write Protect is off
[   15.617675] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   15.617691] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   15.617695]  sda:<4>Driver 'sr' needs updating - please use bus_type methods
[   15.761070] Clocksource tsc unstable (delta = -218908608 ns)
[   15.788530] Time: acpi_pm clocksource has been installed.
[   16.532037]  sda1 sda2 sda3
[   16.560164] sd 0:0:0:0: [sda] Attached SCSI disk
[   16.567617] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   16.567641] sr 1:0:0:0: Attached scsi generic sg1 type 5
[   16.576820] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[   16.576825] Uniform CD-ROM driver Revision: 3.20
[   16.576888] sr 1:0:0:0: Attached scsi CD-ROM sr0
[   16.788588] Attempting manual resume
[   16.788593] swsusp: Resume From Partition 8:3
[   16.788594] PM: Checking swsusp image.
[   16.788811] PM: Resume from disk failed.
[   16.829177] kjournald starting.  Commit interval 5 seconds
[   16.829191] EXT3-fs: mounted filesystem with ordered data mode.
[   25.575595] input: PC Speaker as /devices/platform/pcspkr/input/input2
[   26.075866] Linux agpgart interface v0.102
[   26.111540] agpgart: Detected an Intel 855PM Chipset.
[   26.125314] agpgart: AGP aperture is 256M @ 0xd0000000
[   26.151565] iTCO_vendor_support: vendor-support=0
[   26.175458] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
[   26.175545] iTCO_wdt: Found a ICH4-M TCO device (Version=1, TCOBASE=0x1060)
[   26.175584] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   26.212846] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   26.232848] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   26.331490] parport_pc 00:0b: reported by Plug and Play ACPI
[   26.331536] parport0: PC-style at 0x3bc, irq 7 [PCSPP,TRISTATE]
[   26.467416] Non-volatile memory driver v1.2
[   26.651454] thinkpad_acpi: ThinkPad ACPI Extras v0.17
[   26.651459] thinkpad_acpi: http://ibm-acpi.sf.net/
[   26.651461] thinkpad_acpi: ThinkPad BIOS 1RETDPWW (3.21 ), EC 1RHT71WW-3.04
[   26.651463] thinkpad_acpi: IBM ThinkPad T40 
[   26.658175] thinkpad_acpi: another device driver is already handling bay events
[   26.658179] thinkpad_acpi: disabling subdriver bay
[   26.660668] input: ThinkPad Extra Buttons as /devices/virtual/input/input3
[   26.727285] irda_init()
[   26.727313] NET: Registered protocol family 23
[   26.871849] nsc-ircc 00:0c: activated
[   26.871856] nsc_ircc_pnp_probe() : From PnP, found firbase 0x2F8 ; irq 3 ; dma 1.
[   26.872015] nsc-ircc, chip->init
[   26.872024] nsc-ircc, Found chip at base=0x02e
[   26.872048] nsc-ircc, driver loaded (Dag Brattli)
[   26.872376] IrDA: Registered device irda0
[   26.872379] nsc-ircc, Using dongle: IBM31T1100 or Temic TFDS6000/TFDS6500
[   27.223435] input: Power Button (FF) as /devices/virtual/input/input4
[   27.247191] ACPI: Power Button (FF) [PWRF]
[   27.247278] input: Lid Switch as /devices/virtual/input/input5
[   27.263412] ACPI: Lid Switch [LID]
[   27.263496] input: Sleep Button (CM) as /devices/virtual/input/input6
[   27.291216] ACPI: Sleep Button (CM) [SLPB]
[   28.688550] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:03/LNXVIDEO:00/input/input7
[   28.714956] ACPI: Video Device [VID] (multi-head: yes  rom: no  post: no)
[   28.980901] Yenta: CardBus bridge found at 0000:02:00.0 [1014:0512]
[   28.980920] Yenta: Using INTVAL to route CSC interrupts to PCI
[   28.980922] Yenta: Routing CardBus interrupts to PCI
[   28.980927] Yenta TI: socket 0000:02:00.0, mfunc 0x01d21022, devctl 0x64
[   29.211266] Yenta: ISA IRQ mask 0x0438, PCI irq 11
[   29.211271] Socket status: 30000006
[   29.211275] pcmcia: parent PCI bridge I/O window: 0x4000 - 0x8fff
[   29.211279] cs: IO port probe 0x4000-0x8fff: clean.
[   29.212603] pcmcia: parent PCI bridge Memory window: 0xc0200000 - 0xcfffffff
[   29.212606] pcmcia: parent PCI bridge Memory window: 0xe8000000 - 0xefffffff
[   29.234413] Yenta: CardBus bridge found at 0000:02:00.1 [1014:0512]
[   29.234430] Yenta: Using INTVAL to route CSC interrupts to PCI
[   29.234432] Yenta: Routing CardBus interrupts to PCI
[   29.234437] Yenta TI: socket 0000:02:00.1, mfunc 0x01d21022, devctl 0x64
[   29.463213] Yenta: ISA IRQ mask 0x0438, PCI irq 11
[   29.463218] Socket status: 30000006
[   29.463223] pcmcia: parent PCI bridge I/O window: 0x4000 - 0x8fff
[   29.463226] cs: IO port probe 0x4000-0x8fff: clean.
[   29.464551] pcmcia: parent PCI bridge Memory window: 0xc0200000 - 0xcfffffff
[   29.464554] pcmcia: parent PCI bridge Memory window: 0xe8000000 - 0xefffffff
[   29.510778] ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
[   29.510813] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[   29.578829] ACPI: AC Adapter [AC] (on-line)
[   29.710153] Synaptics Touchpad, model: 1, fw: 5.9, id: 0x2c6ab1, caps: 0x884793/0x0
[   29.710160] serio: Synaptics pass-through port at isa0060/serio1/input0
[   29.743265] ACPI: Battery Slot [BAT0] (battery present)
[   29.764144] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input8
[   29.947796] b43legacy-phy0: Broadcom 4306 WLAN found
[   29.990665] b43legacy-phy0 debug: Found PHY: Analog 1, Type 2, Revision 1
[   29.990688] b43legacy-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
[   30.014669] b43legacy-phy0 debug: Radio initialized
[   30.017914] phy0: Selected rate control algorithm 'simple'
[   30.442608] intel8x0_measure_ac97_clock: measured 55950 usecs
[   30.442614] intel8x0: measured clock 196 rejected
[   30.442616] intel8x0: clocking to 48000
[   31.772751] udev: renamed network interface wmaster0 to eth1
[   31.993218] cs: IO port probe 0x100-0x3af: clean.
[   31.994218] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[   31.994645] cs: IO port probe 0x820-0x8ff: clean.
[   31.995008] cs: IO port probe 0xc00-0xcf7: clean.
[   31.995522] cs: IO port probe 0xa00-0xaff: clean.
[   32.004300] cs: IO port probe 0x100-0x3af: clean.
[   32.005288] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[   32.005715] cs: IO port probe 0x820-0x8ff: clean.
[   32.006101] cs: IO port probe 0xc00-0xcf7: clean.
[   32.006603] cs: IO port probe 0xa00-0xaff: clean.
[   32.283510] IBM TrackPoint firmware: 0x0e, buttons: 3/3
[   32.301354] input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/serio2/input/input9
[   41.384584] lp0: using parport0 (interrupt-driven).
[   41.504671] Adding 1004052k swap on /dev/sda3.  Priority:-1 extents:1 across:1004052k
[   41.984944] EXT3 FS on sda2, internal journal
[   42.119142] device-mapper: uevent: version 1.0.3
[   42.119178] device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@redhat.com
[   43.151514] ip_tables: (C) 2000-2006 Netfilter Core Team
[   44.342034] ACPI: ACPI Dock Station Driver 
[   44.424024] ACPI: \_SB_.PCI0.IDE0.SCND.MSTR: found ejectable bay
[   44.424032] ACPI: \_SB_.PCI0.IDE0.SCND.MSTR: Adding notify handler
[   44.424077] ACPI: Error installing bay notify handler
[   44.424081] ACPI: Bay [\_SB_.PCI0.IDE0.SCND.MSTR] Added
[   44.532034] toshiba_acpi: Unknown parameter `hotkeys_over_acpi'
[   47.837172] b43legacy-phy0 debug: Loading firmware version 0x127, patch level 14 (2005-04-18 02:36:27)
[   47.845930] b43legacy-phy0 debug: Chip initialized
[   47.846625] b43legacy-phy0 debug: 30-bit DMA initialized
[   47.848873] b43legacy-phy0 debug: Wireless interface started
[   47.853710] b43legacy-phy0 debug: Adding Interface type 2
[   47.950318] NET: Registered protocol family 10
[   47.951068] lo: Disabled Privacy Extensions
[   47.952067] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   47.953319] ADDRCONF(NETDEV_UP): wlan0_rename: link is not ready
[   48.274402] ppdev: user-space parallel port driver
[   48.793041] audit(1203630819.762:2): operation="inode_permission" request_mask="a::" denied_mask="a::" name="/dev/tty" pid=5331 profile="/usr/sbin/cupsd" namespace="default"
[   48.910891] IBM machine detected. Enabling interrupts during APM calls.
[   48.910898] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[   48.910901] apm: overridden by ACPI.
[  131.428414] Marking TSC unstable due to: cpufreq changes.
[  131.557439] input: /usr/sbin/thinkpad-keys as /devices/virtual/input/input10
[  132.236643] Bluetooth: Core ver 2.11
[  132.237581] NET: Registered protocol family 31
[  132.237590] Bluetooth: HCI device and connection manager initialized
[  132.237600] Bluetooth: HCI socket layer initialized
[  132.439656] Bluetooth: L2CAP ver 2.9
[  132.439667] Bluetooth: L2CAP socket layer initialized
[  132.515077] Bluetooth: RFCOMM socket layer initialized
[  132.516115] Bluetooth: RFCOMM TTY layer initialized
[  132.516124] Bluetooth: RFCOMM ver 1.8
[   50.693563] [drm] Initialized drm 1.1.0 20060810
[   50.716869] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[   50.717246] [drm] Initialized radeon 1.28.0 20060524 on minor 0
[   50.767140] ndiswrapper version 1.52 loaded (smp=yes, preempt=no)
[   50.893680] usbcore: registered new interface driver ndiswrapper
[  138.182843] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[  138.184103] agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
[  138.185296] agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
[  138.602133] [drm] Setting GART location based on new memory map
[  138.602154] [drm] Loading R200 Microcode
[  138.602212] [drm] writeback test succeeded in 2 usecs
[   90.679053] NET: Registered protocol family 17
[   91.583931] wlan0_rename: Initial auth_alg=0
[   91.583939] wlan0_rename: authenticate with AP 00:0d:88:b7:01:f6
[   91.586861] wlan0_rename: RX authentication from 00:0d:88:b7:01:f6 (alg=0 transaction=2 status=0)
[   91.586866] wlan0_rename: authenticated
[   91.586869] wlan0_rename: associate with AP 00:0d:88:b7:01:f6
[   91.591710] wlan0_rename: RX AssocResp from 00:0d:88:b7:01:f6 (capab=0x431 status=0 aid=2)
[   91.591717] wlan0_rename: associated
[   91.591723] wlan0_rename: switched to short barker preamble (BSSID=00:0d:88:b7:01:f6)
[   91.593386] ADDRCONF(NETDEV_CHANGE): wlan0_rename: link becomes ready
[   94.541163] b43legacy-phy0 debug: Using software based encryption for mac: 00:0d:88:b7:01:f6
[   94.557703] b43legacy-phy0 debug: Using software based encryption for mac: ff:ff:ff:ff:ff:ff
[   99.390284] wlan0_rename: no IPv6 routers present
[  304.103270] wlan0_rename: no IPv6 routers present
[ 1397.823863] mtrr: no MTRR for e0000000,2000000 found
[ 3731.710136] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[ 3731.711456] agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
[ 3731.712620] agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
[ 3732.314244] [drm] Setting GART location based on new memory map
[ 3732.314262] [drm] Loading R200 Microcode
[ 3732.314322] [drm] writeback test succeeded in 1 usecs
[ 1426.851334] mtrr: no MTRR for e0000000,2000000 found
[ 3809.236298] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[ 3809.237616] agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
[ 3809.238863] agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
[ 3809.849619] [drm] Setting GART location based on new memory map
[ 3809.849638] [drm] Loading R200 Microcode
[ 3809.849698] [drm] writeback test succeeded in 1 usecs
[ 1544.875177] mtrr: no MTRR for e0000000,2000000 found
[ 4123.768014] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[ 4123.769287] agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
[ 4123.770489] agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
[ 4124.849739] [drm] Setting GART location based on new memory map
[ 4124.849758] [drm] Loading R200 Microcode
[ 4124.849817] [drm] writeback test succeeded in 1 usecs
[ 8809.188344] b43legacy-phy0 warning: Unexpected value for chanstat (0x7C00)
[ 3778.511291] audit(1203643507.615:3): operation="file_mmap" request_mask="::mr" denied_mask="::m" name="/usr/share/samba/upcase.dat" pid=9109 profile="/usr/sbin/cupsd" namespace="default"
[ 3778.511867] audit(1203643507.615:4): operation="file_mmap" request_mask="::mr" denied_mask="::m" name="/usr/share/samba/lowcase.dat" pid=9109 profile="/usr/sbin/cupsd" namespace="default"
[ 3778.554886] audit(1203643507.655:5): operation="file_mmap" request_mask="::mr" denied_mask="::m" name="/usr/share/samba/valid.dat" pid=9109 profile="/usr/sbin/cupsd" namespace="default"
[ 3778.606666] audit(1203643507.707:6): operation="inode_permission" request_mask="::rw" denied_mask="::rw" name="/dev/tty" pid=9115 profile="/usr/sbin/cupsd" namespace="default"
[ 3778.636899] audit(1203643507.739:7): operation="inode_permission" request_mask="::rw" denied_mask="::rw" name="/dev/tty" pid=9118 profile="/usr/sbin/cupsd" namespace="default"
[ 3796.919851] audit(1203643565.315:8): operation="file_mmap" request_mask="::mr" denied_mask="::m" name="/usr/share/samba/upcase.dat" pid=9135 profile="/usr/sbin/cupsd" namespace="default"
[ 3796.921379] audit(1203643565.319:9): operation="file_mmap" request_mask="::mr" denied_mask="::m" name="/usr/share/samba/lowcase.dat" pid=9135 profile="/usr/sbin/cupsd" namespace="default"
[ 3797.036003] audit(1203643565.431:10): operation="file_mmap" request_mask="::mr" denied_mask="::m" name="/usr/share/samba/valid.dat" pid=9135 profile="/usr/sbin/cupsd" namespace="default"
[ 3797.088630] audit(1203643565.487:11): operation="inode_permission" request_mask="::rw" denied_mask="::rw" name="/dev/tty" pid=9141 profile="/usr/sbin/cupsd" namespace="default"
[ 3797.118210] audit(1203643565.515:12): operation="inode_permission" request_mask="::rw" denied_mask="::rw" name="/dev/tty" pid=9144 profile="/usr/sbin/cupsd" namespace="default"
[ 3923.614470] audit(1203643874.683:13): operation="file_mmap" request_mask="::mr" denied_mask="::m" name="/usr/share/samba/upcase.dat" pid=9193 profile="/usr/sbin/cupsd" namespace="default"
[ 3923.614532] audit(1203643874.683:14): operation="file_mmap" request_mask="::mr" denied_mask="::m" name="/usr/share/samba/lowcase.dat" pid=9193 profile="/usr/sbin/cupsd" namespace="default"
[ 3923.785036] audit(1203643874.855:15): operation="file_mmap" request_mask="::mr" denied_mask="::m" name="/usr/share/samba/valid.dat" pid=9193 profile="/usr/sbin/cupsd" namespace="default"
[ 3923.963423] audit(1203643875.035:16): operation="inode_permission" request_mask="::rw" denied_mask="::rw" name="/dev/tty" pid=9200 profile="/usr/sbin/cupsd" namespace="default"
[ 3924.085266] audit(1203643875.155:17): operation="inode_permission" request_mask="::rw" denied_mask="::rw" name="/dev/tty" pid=9203 profile="/usr/sbin/cupsd" namespace="default"
[51284.134861] wlan0_rename: CTS protection enabled (BSSID=00:0d:88:b7:01:f6)
[51293.101206] wlan0_rename: CTS protection disabled (BSSID=00:0d:88:b7:01:f6)
[52705.049191] wlan0_rename: CTS protection enabled (BSSID=00:0d:88:b7:01:f6)
[52721.835298] wlan0_rename: CTS protection disabled (BSSID=00:0d:88:b7:01:f6)
[23472.344356] b43legacy-phy0 warning: Unexpected value for chanstat (0x7C00)
[77534.028548] wlan0_rename: CTS protection enabled (BSSID=00:0d:88:b7:01:f6)
[77548.752214] wlan0_rename: CTS protection disabled (BSSID=00:0d:88:b7:01:f6)
[32954.195150] b43legacy-phy0 debug: Removing Interface type 2
[32954.212780] b43legacy-phy0 debug: Wireless interface stopped
[32954.212850] b43legacy-phy0 debug: DMA-32 0x0260 (RX) max used slots: 2/64
[32954.212912] b43legacy-phy0 debug: DMA-32 0x0200 (RX) max used slots: 17/64
[32954.212967] b43legacy-phy0 debug: DMA-32 0x02A0 (TX) max used slots: 0/128
[32954.217571] b43legacy-phy0 debug: DMA-32 0x0280 (TX) max used slots: 0/128
[32954.225611] b43legacy-phy0 debug: DMA-32 0x0260 (TX) max used slots: 0/128
[32954.233609] b43legacy-phy0 debug: DMA-32 0x0240 (TX) max used slots: 0/128
[32954.241588] b43legacy-phy0 debug: DMA-32 0x0220 (TX) max used slots: 128/128
[32954.249564] b43legacy-phy0 debug: DMA-32 0x0200 (TX) max used slots: 0/128
[32954.257577] b43legacy-phy0 debug: Radio initialized
[32954.257600] b43legacy-phy0 debug: Radio initialized
[32954.318662] wlan0_rename: deauthenticate(reason=3)
[32954.705988] b43legacy-phy0 debug: Loading firmware version 0x127, patch level 14 (2005-04-18 02:36:27)
[32954.764131] b43legacy-phy0 debug: Chip initialized
[32954.764437] b43legacy-phy0 debug: 30-bit DMA initialized
[32954.764535] b43legacy-phy0 debug: Wireless interface started
[32954.764539] b43legacy-phy0 debug: Adding Interface type 2
[32954.767478] ADDRCONF(NETDEV_UP): wlan0_rename: link is not ready
[32955.203511] b43legacy-phy0 debug: Removing Interface type 2
[32955.238557] b43legacy-phy0 debug: Wireless interface stopped
[32955.238618] b43legacy-phy0 debug: DMA-32 0x0260 (RX) max used slots: 0/64
[32955.238672] b43legacy-phy0 debug: DMA-32 0x0200 (RX) max used slots: 0/64
[32955.238734] b43legacy-phy0 debug: DMA-32 0x02A0 (TX) max used slots: 0/128
[32955.243529] b43legacy-phy0 debug: DMA-32 0x0280 (TX) max used slots: 0/128
[32955.251505] b43legacy-phy0 debug: DMA-32 0x0260 (TX) max used slots: 0/128
[32955.259511] b43legacy-phy0 debug: DMA-32 0x0240 (TX) max used slots: 0/128
[32955.267505] b43legacy-phy0 debug: DMA-32 0x0220 (TX) max used slots: 0/128
[32955.275500] b43legacy-phy0 debug: DMA-32 0x0200 (TX) max used slots: 0/128
[32955.283498] b43legacy-phy0 debug: Radio initialized
[32955.283513] b43legacy-phy0 debug: Radio initialized
[32955.482518] Syncing filesystems ... done.
[32955.482770] PM: Preparing system for mem sleep
[32955.483246] Freezing user space processes ... (elapsed 0.00 seconds) done.
[32955.484627] Freezing remaining freezable tasks ... (elapsed 0.09 seconds) done.
[32955.579460] PM: Entering mem sleep
[32955.579463] Suspending console(s)
[32955.591429] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[32955.591598] sd 0:0:0:0: [sda] Stopping disk
[32955.592844] b43legacy-phy0 debug: Suspending...
[32955.592846] b43legacy-phy0 debug: Device suspended.
[32955.598883] nsc-ircc 00:0c: disabled
[32955.599035] parport_pc 00:0b: disabled
[32955.599178] serial 00:0a: disabled
[32955.599281] ACPI: PCI interrupt for device 0000:02:02.0 disabled
[32955.599286] ACPI handle has no context!
[32955.599619] ACPI: PCI interrupt for device 0000:02:01.0 disabled
[32955.599625] ACPI handle has no context!
[32955.600170] ACPI: PCI interrupt for device 0000:00:1f.5 disabled
[32955.600304] ACPI: PCI interrupt for device 0000:00:1f.1 disabled
[32955.600393] ACPI: PCI interrupt for device 0000:00:1d.7 disabled
[32955.616741] ACPI: PCI interrupt for device 0000:00:1d.2 disabled
[32955.616770] ACPI: PCI interrupt for device 0000:00:1d.1 disabled
[32955.616797] ACPI: PCI interrupt for device 0000:00:1d.0 disabled
[32955.622263] Disabling non-boot CPUs ...
[    0.900073] Back to C!
[    0.917995] PCI: Enabling device 0000:00:1d.0 (0000 -> 0001)
[    0.918001] ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[    0.918009] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[    0.918015] PM: Writing back config space on device 0000:00:1d.0 at offset f (was 100, writing 10b)
[    0.918026] PM: Writing back config space on device 0000:00:1d.0 at offset 8 (was 1, writing 1801)
[    0.918056] usb usb1: root hub lost power or was reset
[    0.918072] PCI: Enabling device 0000:00:1d.1 (0000 -> 0001)
[    0.918076] ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
[    0.918083] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[    0.918088] PM: Writing back config space on device 0000:00:1d.1 at offset f (was 200, writing 20b)
[    0.918100] PM: Writing back config space on device 0000:00:1d.1 at offset 8 (was 1, writing 1821)
[    0.918127] usb usb2: root hub lost power or was reset
[    0.918146] PCI: Enabling device 0000:00:1d.2 (0000 -> 0001)
[    0.918149] ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
[    0.918156] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[    0.918162] PM: Writing back config space on device 0000:00:1d.2 at offset f (was 300, writing 30b)
[    0.918173] PM: Writing back config space on device 0000:00:1d.2 at offset 8 (was 1, writing 1841)
[    0.918201] usb usb3: root hub lost power or was reset
[    0.934030] PCI: Enabling device 0000:00:1d.7 (0000 -> 0002)
[    0.934035] ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11
[    0.934042] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[    0.934055] PM: Writing back config space on device 0000:00:1d.7 at offset f (was 400, writing 40b)
[    0.934073] PM: Writing back config space on device 0000:00:1d.7 at offset 4 (was 0, writing c0000000)
[    0.934081] PM: Writing back config space on device 0000:00:1d.7 at offset 1 (was 2900006, writing 2900106)
[    0.934151] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[    0.934186] PM: Writing back config space on device 0000:00:1f.1 at offset 9 (was 0, writing 70000000)
[    0.934198] PM: Writing back config space on device 0000:00:1f.1 at offset 1 (was 2800005, writing 2800007)
[    0.934209] ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
[    0.934215] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[    0.935249] ata1.01: _GTF evaluation failed (AE 0x1001)
[    0.935600] PM: Writing back config space on device 0000:00:1f.5 at offset 1 (was 2900007, writing 2900003)
[    0.936115] ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
[    0.936122] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[    0.936391] ata2.01: _GTF evaluation failed (AE 0x1001)
[    1.409541] ata2.00: ACPI cmd ef/03:42:00:00:00:a0 filtered out
[    1.409544] ata2.00: ACPI cmd ef/03:0c:00:00:00:a0 filtered out
[    1.409748] ata2.00: ACPI cmd e3/00:1f:00:00:00:a0 succeeded
[    1.409989] ata2.00: ACPI cmd e3/00:02:00:00:00:a0 succeeded
[    1.745416] ata2.00: configured for UDMA/33
[    1.908383] PM: Writing back config space on device 0000:00:1f.6 at offset 1 (was 2900005, writing 2900001)
[    1.908468] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[    1.922541] PM: Writing back config space on device 0000:02:01.0 at offset f (was ff0100, writing ff010b)
[    1.922555] PM: Writing back config space on device 0000:02:01.0 at offset 6 (was 1, writing 8001)
[    1.922560] PM: Writing back config space on device 0000:02:01.0 at offset 5 (was 0, writing c0200000)
[    1.922565] PM: Writing back config space on device 0000:02:01.0 at offset 4 (was 0, writing c0220000)
[    1.922570] PM: Writing back config space on device 0000:02:01.0 at offset 3 (was 0, writing 4008)
[    1.922576] PM: Writing back config space on device 0000:02:01.0 at offset 1 (was 2300000, writing 2300117)
[    1.922593] ACPI: PCI Interrupt 0000:02:01.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[    1.929229] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 succeeded
[    1.929232] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
[    1.929235] ata1.00: ACPI cmd ef/03:45:00:00:00:a0 filtered out
[    1.929238] ata1.00: ACPI cmd ef/03:0c:00:00:00:a0 filtered out
[    1.930452] ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
[    1.930961] serial 00:0a: activated
[    1.931416] parport_pc 00:0b: activated
[    1.931941] nsc-ircc 00:0c: activated
[    1.935134] ata1.00: configured for UDMA/100
[    1.938581] ata1.00: configured for UDMA/100
[    1.938584] ata1: EH complete
[    1.938624] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[    1.938638] sd 0:0:0:0: [sda] Write Protect is off
[    1.938641] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.938659] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.938676] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[    1.938685] sd 0:0:0:0: [sda] Write Protect is off
[    1.938688] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.938703] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.512276] b43legacy-phy0 debug: Resuming...
[    2.512279] b43legacy-phy0 debug: Device resumed.
[    2.512283] sd 0:0:0:0: [sda] Starting disk
[    5.170430] PM: Finishing wakeup.
[    5.170432] Restarting tasks ... <3>hub 2-0:1.0: over-current change on port 1
[    5.285787] done.
[    5.327918] hub 2-0:1.0: over-current change on port 2
[    5.436150] hub 4-0:1.0: over-current change on port 3
[    5.545461] hub 4-0:1.0: over-current change on port 4
[    7.872105] b43legacy-phy0 debug: Loading firmware version 0x127, patch level 14 (2005-04-18 02:36:27)
[    7.949850] b43legacy-phy0 debug: Chip initialized
[    7.950184] b43legacy-phy0 debug: 30-bit DMA initialized
[    7.950288] b43legacy-phy0 debug: Wireless interface started
[    7.950292] b43legacy-phy0 debug: Adding Interface type 2
[    7.953362] ADDRCONF(NETDEV_UP): wlan0_rename: link is not ready
[    8.000316] ADDRCONF(NETDEV_UP): eth0: link is not ready
[    8.786738] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[    8.786760] agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
[    8.786792] agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
[    8.786823] [drm] Loading R200 Microcode
[   36.890754] wlan0_rename: Initial auth_alg=0
[   36.890769] wlan0_rename: authenticate with AP 00:0d:88:b7:01:f6
[   36.892221] wlan0_rename: RX authentication from 00:0d:88:b7:01:f6 (alg=0 transaction=2 status=0)
[   36.892230] wlan0_rename: authenticated
[   36.892238] wlan0_rename: associate with AP 00:0d:88:b7:01:f6
[   36.894855] wlan0_rename: RX AssocResp from 00:0d:88:b7:01:f6 (capab=0x431 status=0 aid=2)
[   36.894864] wlan0_rename: associated
[   36.894874] wlan0_rename: switched to short barker preamble (BSSID=00:0d:88:b7:01:f6)
[   36.898939] ADDRCONF(NETDEV_CHANGE): wlan0_rename: link becomes ready
[   40.439730] b43legacy-phy0 debug: Using software based encryption for mac: 00:0d:88:b7:01:f6
[   40.444699] b43legacy-phy0 debug: Using software based encryption for mac: ff:ff:ff:ff:ff:ff
[   56.747389] wlan0_rename: no IPv6 routers present
[  165.145251] 
[  165.145262] floppy driver state
[  165.145266] -------------------
[  165.145273] now=25179906 last interrupt=4294906976 diff=25240226 last called handler=f890f360
[  165.145281] timeout_message=lock fdc
[  165.145285] last output bytes:
[  165.145290] 18 80 4294893092
[  165.145295]  8 80 4294893092
[  165.145300]  8 80 4294893092
[  165.145304]  8 80 4294893092
[  165.145308]  8 80 4294893092
[  165.145313] 12 80 4294906797
[  165.145317]  0 90 4294906797
[  165.145321] 13 80 4294906797
[  165.145325]  0 90 4294906797
[  165.145330] 1a 90 4294906797
[  165.145334]  0 90 4294906797
[  165.145338]  3 80 4294906797
[  165.145342] c1 90 4294906797
[  165.145347] 10 90 4294906797
[  165.145351]  7 80 4294906797
[  165.145355]  0 90 4294906797
[  165.145359]  8 81 4294906884
[  165.145363]  7 80 4294906889
[  165.145368]  0 90 4294906889
[  165.145372]  8 81 4294906976
[  165.145376] last result at 4294906976
[  165.145380] last redo_fd_request at 4294906976
[  165.145385] 70  0 
[  165.145394] status=0
[  165.145398] fdc_busy=1
[  165.145402] do_floppy=f890f540
[  165.145407] cont=f89156a0
[  165.145410] current_req=00000000
[  165.145414] command_status=-1
[  165.145418] 
[  165.145424] floppy0: floppy timeout called
[  167.604327] 
[  167.604337] floppy driver state
[  167.604342] -------------------
[  167.604349] now=25180656 last interrupt=4294906976 diff=25240976 last called handler=f890f360
[  167.604357] timeout_message=lock fdc
[  167.604361] last output bytes:
[  167.604366] 18 80 4294893092
[  167.604371]  8 80 4294893092
[  167.604375]  8 80 4294893092
[  167.604380]  8 80 4294893092
[  167.604384]  8 80 4294893092
[  167.604388] 12 80 4294906797
[  167.604392]  0 90 4294906797
[  167.604397] 13 80 4294906797
[  167.604401]  0 90 4294906797
[  167.604405] 1a 90 4294906797
[  167.604409]  0 90 4294906797
[  167.604414]  3 80 4294906797
[  167.604418] c1 90 4294906797
[  167.604422] 10 90 4294906797
[  167.604426]  7 80 4294906797
[  167.604431]  0 90 4294906797
[  167.604435]  8 81 4294906884
[  167.604439]  7 80 4294906889
[  167.604444]  0 90 4294906889
[  167.604448]  8 81 4294906976
[  167.604452] last result at 4294906976
[  167.604456] last redo_fd_request at 25179906
[  167.604461] 70  0 
[  167.604470] status=0
[  167.604474] fdc_busy=1
[  167.604478] do_floppy=f890f540
[  167.604482] cont=f8915634
[  167.604486] current_req=00000000
[  167.604490] command_status=-1
[  167.604493] 
[  167.604499] floppy0: floppy timeout called
[ 8592.867155] b43legacy-phy0 warning: Unexpected value for chanstat (0x7C00)
[ 4779.081028] audit(1203753095.298:18): operation="file_mmap" request_mask="::mr" denied_mask="::m" name="/usr/share/samba/upcase.dat" pid=16668 profile="/usr/sbin/cupsd" namespace="default"
[ 4779.081125] audit(1203753095.298:19): operation="file_mmap" request_mask="::mr" denied_mask="::m" name="/usr/share/samba/lowcase.dat" pid=16668 profile="/usr/sbin/cupsd" namespace="default"
[ 4779.129988] audit(1203753095.346:20): operation="file_mmap" request_mask="::mr" denied_mask="::m" name="/usr/share/samba/valid.dat" pid=16668 profile="/usr/sbin/cupsd" namespace="default"
[ 4779.312602] audit(1203753095.530:21): operation="inode_permission" request_mask="::rw" denied_mask="::rw" name="/dev/tty" pid=16674 profile="/usr/sbin/cupsd" namespace="default"
[ 4779.393732] audit(1203753095.610:22): operation="inode_permission" request_mask="::rw" denied_mask="::rw" name="/dev/tty" pid=16677 profile="/usr/sbin/cupsd" namespace="default"