[   29.262795] Did not find alt setting 1 for intf 0, config 1
[   29.732134] init: plymouth-stop pre-start process (1220) terminated with status 1
[   30.413168] Initializing USB Mass Storage driver...
[   30.423909] scsi4 : usb-storage 1-3:1.2
[   30.424145] usbcore: registered new interface driver usb-storage
[   30.424150] USB Mass Storage support registered.
[   30.458542] usbcore: registered new interface driver uas
[   31.436206] scsi 4:0:0:0: Direct-Access     EPSON    Storage          1.00 PQ: 0 ANSI: 2
[   31.448241] sd 4:0:0:0: Attached scsi generic sg2 type 0
[   31.459943] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[   37.848031] eth1: no IPv6 routers present
[ 4035.912591] usb 1-3: USB disconnect, device number 4
[ 4039.136025] usb 1-4: new high-speed USB device number 5 using ehci_hcd
[ 4039.283626] scsi5 : usb-storage 1-4:1.2
[ 4039.440717] Did not find alt setting 1 for intf 0, config 1
[ 4040.282858] scsi 5:0:0:0: Direct-Access     EPSON    Storage          1.00 PQ: 0 ANSI: 2
[ 4040.290364] sd 5:0:0:0: Attached scsi generic sg2 type 0
[ 4040.302385] sd 5:0:0:0: [sdb] Attached SCSI removable disk
[422227.440038] usb 1-8: new high-speed USB device number 6 using ehci_hcd
[422227.574693] scsi6 : usb-storage 1-8:1.0
[422228.094674] usb 1-8: USB disconnect, device number 6
[422228.592026] usb 1-8: new high-speed USB device number 7 using ehci_hcd
[422228.731984] scsi7 : usb-storage 1-8:1.0
[422229.732927] scsi 7:0:0:0: Direct-Access     Philips  GoGear Vibe      0100 PQ: 0 ANSI: 4
[422229.738482] sd 7:0:0:0: Attached scsi generic sg3 type 0
[422229.739291] sd 7:0:0:0: [sdc] 960768 4096-byte logical blocks: (3.93 GB/3.66 GiB)
[422229.739767] sd 7:0:0:0: [sdc] Write Protect is off
[422229.739772] sd 7:0:0:0: [sdc] Mode Sense: 3e 00 00 00
[422229.740457] sd 7:0:0:0: [sdc] No Caching mode page present
[422229.740464] sd 7:0:0:0: [sdc] Assuming drive cache: write through
[422229.741925] sd 7:0:0:0: [sdc] 960768 4096-byte logical blocks: (3.93 GB/3.66 GiB)
[422229.743787] sd 7:0:0:0: [sdc] No Caching mode page present
[422229.743795] sd 7:0:0:0: [sdc] Assuming drive cache: write through
[422229.753278]  sdc: sdc1
[422229.754799] sd 7:0:0:0: [sdc] 960768 4096-byte logical blocks: (3.93 GB/3.66 GiB)
[422229.755770] sd 7:0:0:0: [sdc] No Caching mode page present
[422229.755778] sd 7:0:0:0: [sdc] Assuming drive cache: write through
[422229.755783] sd 7:0:0:0: [sdc] Attached SCSI removable disk
[425052.658890] usb 1-4: USB disconnect, device number 5
[427956.545150] usb 1-8: USB disconnect, device number 7
[642811.252245] usb 1-4: new high-speed USB device number 8 using ehci_hcd
[642811.403025] scsi8 : usb-storage 1-4:1.2
[642811.808881] Did not find alt setting 1 for intf 0, config 1
[642812.405813] scsi 8:0:0:0: Direct-Access     EPSON    Storage          1.00 PQ: 0 ANSI: 2
[642812.411023] sd 8:0:0:0: Attached scsi generic sg2 type 0
[642812.421157] sd 8:0:0:0: [sdb] Attached SCSI removable disk
[709217.337086] usb 1-4: USB disconnect, device number 8
[715634.685491] show_signal_msg: 36 callbacks suppressed
[715634.685500] compiz[4193]: segfault at 2e797479 ip b7706d0a sp bf925d7c error 4 in libcompiz_core.so.0.9.7.8[b76c2000+ac000]