[   28.260015] eth1: no IPv6 routers present
[   32.371712] [drm] DAC-6: set mode 640x480 0
[   32.477724] [drm] DAC-6: set mode 640x480 0
[   32.559758] i2c-adapter i2c-1: unable to read EDID block.
[   32.559763] i915 0000:00:02.0: LVDS-1: no EDID data
[   32.601401] [drm] TV-12: set mode NTSC 480i 0
[   32.741952] [drm] TV-12: set mode NTSC 480i 0
[   32.946862] [drm] DAC-6: set mode 640x480 0
[   33.052281] [drm] DAC-6: set mode 640x480 0
[   33.133352] i2c-adapter i2c-1: unable to read EDID block.
[   33.133356] i915 0000:00:02.0: LVDS-1: no EDID data
[   33.175007] [drm] TV-12: set mode NTSC 480i 0
[   33.315675] [drm] TV-12: set mode NTSC 480i 0
[   33.547302] [drm] DAC-6: set mode 640x480 0
[   33.653447] [drm] DAC-6: set mode 640x480 0
[   33.734334] i2c-adapter i2c-1: unable to read EDID block.
[   33.734338] i915 0000:00:02.0: LVDS-1: no EDID data
[   33.775928] [drm] TV-12: set mode NTSC 480i 0
[   33.917517] [drm] TV-12: set mode NTSC 480i 0
[   71.522648] [drm] DAC-6: set mode 640x480 0
[   71.628574] [drm] DAC-6: set mode 640x480 0
[   71.715650] i2c-adapter i2c-1: unable to read EDID block.
[   71.715658] i915 0000:00:02.0: LVDS-1: no EDID data
[   71.757427] [drm] TV-12: set mode NTSC 480i 0
[   71.906497] [drm] TV-12: set mode NTSC 480i 0
[   72.071770] [drm] DAC-6: set mode 640x480 0
[   72.226104] [drm] DAC-6: set mode 640x480 0
[   72.305138] i2c-adapter i2c-1: unable to read EDID block.
[   72.305143] i915 0000:00:02.0: LVDS-1: no EDID data
[   72.346773] [drm] TV-12: set mode NTSC 480i 0
[   72.487753] [drm] TV-12: set mode NTSC 480i 0
[   72.644740] [drm] DAC-6: set mode 640x480 0
[   72.755124] [drm] DAC-6: set mode 640x480 0
[   72.848425] i2c-adapter i2c-1: unable to read EDID block.
[   72.848432] i915 0000:00:02.0: LVDS-1: no EDID data
[   72.890080] [drm] TV-12: set mode NTSC 480i 0
[   73.031581] [drm] TV-12: set mode NTSC 480i 0
[ 8370.556093] usb 1-4: new high speed USB device using ehci_hcd and address 2
[ 8370.689091] usb 1-4: configuration #1 chosen from 1 choice
[ 8370.753819] Initializing USB Mass Storage driver...
[ 8370.755346] scsi2 : SCSI emulation for USB Mass Storage devices
[ 8370.755648] usbcore: registered new interface driver usb-storage
[ 8370.755657] USB Mass Storage support registered.
[ 8370.756695] usb-storage: device found at 2
[ 8370.756700] usb-storage: waiting for device to settle before scanning
[ 8375.756237] usb-storage: device scan complete
[ 8375.756729] scsi 2:0:0:0: Direct-Access     CBM      Flash Disk       5.00 PQ: 0 ANSI: 2
[ 8375.757561] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 8375.774337] sd 2:0:0:0: [sdb] 2053120 512-byte logical blocks: (1.05 GB/1002 MiB)
[ 8375.774800] sd 2:0:0:0: [sdb] Write Protect is off
[ 8375.774804] sd 2:0:0:0: [sdb] Mode Sense: 0b 00 00 08
[ 8375.774807] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 8375.777289] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 8375.777294]  sdb: sdb1
[ 8375.782829] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 8375.782836] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 8490.840067] usb 1-4: USB disconnect, address 2