[   14.274699] ata1.00: configured for UDMA/133
[   14.274702] ata1: EH complete
[   14.426503] ata2.00: configured for UDMA/133
[   14.426506] ata2: EH complete
[   14.626644] ata3.00: configured for UDMA/133
[   14.626647] ata3: EH complete
[   14.733339] EXT4-fs (md0): re-mounted. Opts: commit=0
[   17.068682] ata1.00: configured for UDMA/133
[   17.068686] ata1: EH complete
[   17.237615] ata2.00: configured for UDMA/133
[   17.237618] ata2: EH complete
[   17.436284] ata3.00: configured for UDMA/133
[   17.436287] ata3: EH complete
[   17.493713] EXT4-fs (md0): re-mounted. Opts: commit=0
[   17.945028] hda-intel: IRQ timing workaround is activated for card #1. Suggest a bigger bdl_pos_adj.
[   24.250070] eth0: no IPv6 routers present
[  158.441708] md: md3: resync done.
[  158.446506] md: resync of RAID array md2
[  158.446513] md: minimum _guaranteed_  speed: 1000 KB/sec/disk.
[  158.446519] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync.
[  158.446528] md: using 128k window, over a total of 944335808 blocks.
[  158.463260] RAID conf printout:
[  158.463267]  --- level:5 rd:3 wd:3
[  158.463273]  disk 0, o:1, dev:sda5
[  158.463278]  disk 1, o:1, dev:sdb5
[  158.463282]  disk 2, o:1, dev:sdc5
[  650.567809] ata3.00: exception Emask 0x10 SAct 0x1e0 SErr 0x280100 action 0x6 frozen
[  650.567818] ata3.00: irq_stat 0x08000000, interface fatal error
[  650.567826] ata3: SError: { UnrecovData 10B8B BadCRC }
[  650.567833] ata3.00: failed command: READ FPDMA QUEUED
[  650.567846] ata3.00: cmd 60/00:28:00:22:f0/01:00:07:00:00/40 tag 5 ncq 131072 in
[  650.567849]          res 40/00:30:80:23:f0/00:00:07:00:00/40 Emask 0x10 (ATA bus error)
[  650.567855] ata3.00: status: { DRDY }
[  650.567860] ata3.00: failed command: READ FPDMA QUEUED
[  650.567871] ata3.00: cmd 60/80:30:80:23:f0/00:00:07:00:00/40 tag 6 ncq 65536 in
[  650.567874]          res 40/00:30:80:23:f0/00:00:07:00:00/40 Emask 0x10 (ATA bus error)
[  650.567879] ata3.00: status: { DRDY }
[  650.567884] ata3.00: failed command: READ FPDMA QUEUED
[  650.567894] ata3.00: cmd 60/00:38:00:24:f0/01:00:07:00:00/40 tag 7 ncq 131072 in
[  650.567897]          res 40/00:30:80:23:f0/00:00:07:00:00/40 Emask 0x10 (ATA bus error)
[  650.567902] ata3.00: status: { DRDY }
[  650.567906] ata3.00: failed command: READ FPDMA QUEUED
[  650.567917] ata3.00: cmd 60/88:40:78:25:f0/00:00:07:00:00/40 tag 8 ncq 69632 in
[  650.567920]          res 40/00:30:80:23:f0/00:00:07:00:00/40 Emask 0x10 (ATA bus error)
[  650.567925] ata3.00: status: { DRDY }
[  650.567933] ata3: hard resetting link
[  651.094256] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[  651.096759] ata3.00: configured for UDMA/133
[  651.096788] ata3: EH complete