[ 2084.781301] usb 1-4: New USB device found, idVendor=0781, idProduct=5406
[ 2084.781310] usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2084.781317] usb 1-4: Product: U3 Cruzer Micro
[ 2084.781323] usb 1-4: Manufacturer: SanDisk Corporation
[ 2084.781330] usb 1-4: SerialNumber: 0000183FA775B300
[ 2084.926798] Initializing USB Mass Storage driver...
[ 2084.927052] scsi2 : usb-storage 1-4:1.0
[ 2084.927985] usbcore: registered new interface driver usb-storage
[ 2084.927991] USB Mass Storage support registered.
[ 2085.924932] scsi 2:0:0:0: Direct-Access     SanDisk  U3 Cruzer Micro  4.05 PQ: 0 ANSI: 2
[ 2085.926730] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 2085.927526] sd 2:0:0:0: [sdb] 8027789 512-byte logical blocks: (4.11 GB/3.82 GiB)
[ 2085.928433] sd 2:0:0:0: [sdb] Write Protect is off
[ 2085.928443] sd 2:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 2085.929143] sd 2:0:0:0: [sdb] No Caching mode page present
[ 2085.929152] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 2085.935025] sd 2:0:0:0: [sdb] No Caching mode page present
[ 2085.935038] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 2085.941325]  sdb: sdb1
[ 2085.945658] sd 2:0:0:0: [sdb] No Caching mode page present
[ 2085.945670] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 2085.945680] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 2200.928129] ssb: Found chip with id 0x4318, rev 0x02 and package 0x02
[ 2200.928153] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x0D, vendor 0x4243)
[ 2200.928172] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x09, vendor 0x4243)
[ 2200.928189] ssb: Core 2 found: PCI (cc 0x804, rev 0x0C, vendor 0x4243)
[ 2200.928207] ssb: Core 3 found: PCMCIA (cc 0x80D, rev 0x07, vendor 0x4243)
[ 2200.972081] ssb: Sonics Silicon Backplane found on PCI device 0000:06:02.0
[ 2201.040118] cfg80211: Calling CRDA to update world regulatory domain
[ 2201.137867] cfg80211: World regulatory domain updated:
[ 2201.137875] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 2201.137879] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 2201.137882] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 2201.137884] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 2201.137887] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 2201.137889] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 2201.138583] b43-phy0: Broadcom 4318 WLAN found (core revision 9)
[ 2201.180070] b43-phy0: Found PHY: Analog 3, Type 2 (G), Revision 7
[ 2201.204359] Broadcom 43xx driver loaded [ Features: PNL ]
[ 2201.271822] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 2201.568085] b43-phy0: Loading firmware version 666.2 (2011-02-23 01:15:07)
[ 2201.651526] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2201.652395] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2225.817045] wlan0: authenticate with 08:86:3b:dd:89:d6
[ 2225.852236] wlan0: send auth to 08:86:3b:dd:89:d6 (try 1/3)
[ 2225.854712] wlan0: authenticated
[ 2225.860066] wlan0: associate with 08:86:3b:dd:89:d6 (try 1/3)
[ 2225.862393] wlan0: RX AssocResp from 08:86:3b:dd:89:d6 (capab=0x411 status=0 aid=4)
[ 2225.863109] wlan0: associated
[ 2225.863168] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 2225.863295] cfg80211: Calling CRDA for country: TW
[ 2225.890481] cfg80211: Regulatory domain changed to country: TW
[ 2225.890491] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 2225.890499] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 2225.890506] cfg80211:   (5270000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[ 2225.890513] cfg80211:   (5735000 KHz - 5815000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[ 2226.604944] IPv6: wlan0: IPv6 duplicate address fe80::214:a5ff:fea2:16b5 detected!
[ 2232.858103] sdb: detected capacity change from 4110227968 to 0
[ 2237.590134] usb 1-4: USB disconnect, device number 2