[    5.019117] r8169 0000:03:00.0 eth0: link up
[    5.019127] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    5.389742] input: HDA ATI SB Front Headphone as /devices/pci0000:00/0000:00:14.2/sound/card0/input10
[    5.389885] input: HDA ATI SB Line Out as /devices/pci0000:00/0000:00:14.2/sound/card0/input9
[    5.389963] input: HDA ATI SB Line as /devices/pci0000:00/0000:00:14.2/sound/card0/input8
[    5.390039] input: HDA ATI SB Front Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input7
[    5.390126] input: HDA ATI SB Rear Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input6
[    5.390531] hda_intel: Disabling MSI
[    5.390542] hda-intel 0000:01:00.1: Handle VGA-switcheroo audio client
[    5.390564] hda-intel 0000:01:00.1: Disabling 64bit DMA
[    5.393945] hda-intel 0000:01:00.1: Enable delay in RIRB handling
[    6.197640] input: HDA NVidia HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input14
[    6.197731] input: HDA NVidia HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input13
[    6.197849] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input12
[    6.197931] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input11
[ 1023.723026] hub 7-0:1.0: port 2 disabled by hub (EMI?), re-enabling...
[ 1023.723043] usb 7-2: USB disconnect, device number 3
[ 1024.004878] usb 7-2: new low-speed USB device number 4 using ohci-pci
[ 1024.170575] usb 7-2: New USB device found, idVendor=1d57, idProduct=0008
[ 1024.170587] usb 7-2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 1024.170594] usb 7-2: Product: 2.4G Wireless Optical Mouse
[ 1024.178337] input: 2.4G Wireless Optical Mouse as /devices/pci0000:00/0000:00:16.0/usb7/7-2/7-2:1.0/input/input15
[ 1024.178753] hid-generic 0003:1D57:0008.0004: input,hidraw2: USB HID v1.10 Mouse [2.4G Wireless Optical Mouse] on usb-0000:00:16.0-2/input0
[ 1033.889676] usb 8-2: new full-speed USB device number 2 using xhci_hcd
[ 1033.936109] usb 8-2: New USB device found, idVendor=04b8, idProduct=085c
[ 1033.936120] usb 8-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1033.936127] usb 8-2: Product: EPSON Epson Stylus SX125 Series
[ 1033.936133] usb 8-2: Manufacturer: EPSON
[ 1033.936138] usb 8-2: SerialNumber: MDLZ614600        
[ 1033.963352] WARNING! power/level is deprecated; use power/control instead
[ 1033.982140] usblp 8-2:1.1: usblp0: USB Bidirectional printer dev 2 if 1 alt 0 proto 2 vid 0x04B8 pid 0x085C
[ 1033.982165] usbcore: registered new interface driver usblp
[ 1092.212093] usblp0: removed
[ 1092.231962] usblp 8-2:1.1: usblp0: USB Bidirectional printer dev 2 if 1 alt 0 proto 2 vid 0x04B8 pid 0x085C
[ 1166.915374] usb 8-2: USB disconnect, device number 2
[ 1166.915664] usblp0: removed
[ 1176.485336] usb 8-2: new full-speed USB device number 3 using xhci_hcd
[ 1176.532213] usb 8-2: New USB device found, idVendor=04b8, idProduct=085c
[ 1176.532225] usb 8-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1176.532232] usb 8-2: Product: EPSON Epson Stylus SX125 Series
[ 1176.532238] usb 8-2: Manufacturer: EPSON
[ 1176.532243] usb 8-2: SerialNumber: MDLZ614600        
[ 1176.550394] usblp 8-2:1.1: usblp0: USB Bidirectional printer dev 3 if 1 alt 0 proto 2 vid 0x04B8 pid 0x085C
[ 1177.594153] usblp0: removed
[ 1177.614498] usblp 8-2:1.1: usblp0: USB Bidirectional printer dev 3 if 1 alt 0 proto 2 vid 0x04B8 pid 0x085C