Serpenting & K3B will burn CD RW but no CD R disks.

Bug #251712 reported by WestCoast on 2008-07-25
2
Affects Status Importance Assigned to Milestone
cdrkit (Ubuntu)
Undecided
Unassigned

Bug Description

Binary package hint: cdrecord

I have recently installed Ubuntu 7.10 in testing hardware I discovered my cd rw had mounting issues, permission issues, and writing issues. My CD RW would not burn data or audio to a CD R. It will however, burn to a CD RW.

Media: Memorex and Verbatim CD R (52x 700 meg 80 min) disks failed every test to write to disk. Attempts were made to burn both data disks and audio disk to new CD-R's. All Serpentine and K3B attempts to burn a cd failed regardless of the format. I then attempted to burn on a rewritable disk. CD burned successfully on the first attempt. Memorex CD rewritable (12x 700 MB 80 min and 4x 700 MB 80 min) disks successfully recorded both data disk and audio disk.

The cd burner would not burn even a single small data file to disk. So I tried to burn audio with the same result. The following is data taken during two attempts to burn audio to a CD-R disk.
Memorex CD R problems

Audio Disc Properties (desktop icon)
 Basic tab
  Name: Audio Disc
  Type: unknown type
  size: unknown
  Location: on the desktop.
  MIME type: application/octet-stream
 Permissions
  The permission of “cdda” could not be determined
 Drive:
  Vendor: LITEON
  Model: CD-Rom LTN526D
  Serial:
  Firmware: YSR7
  Connection: SCSI
  Media: CD-Rom Drive
  Removable: Yes (ejectable)
  External: No
 Volume tab
  Label:
  Size: 328.3 MB
  Media: Auto Disk
  UUID:
  File System:
  Mount Point: Not mounted
  File system: Not mounted
  Mount Options: Not mounted

Bank CD-R Disk Properties:
 OWNER: unknown
  Vendor: ATAPI
  Model: CD-rw 52x24
  Serial:
  Firmware: KFC
  Connection: SCSI
  Media: CD-RW Drive
  Removable: Yes (electable)
  External: No
Volume tab
  Label:
  Size: 2.0 KB
  Media: BLANK CD-R Disk
  UUID:
  File System:
  Mount Point: Not mounted
  File system: Not mounted
  Mount Options: Not mounted
***********************************************

Disk Mounter 2.20 (disk icon on toolbar) reads (CD-Rom Drive mounted):
Disk Mounter 2.20 (disk icon on toolbar) reads (CD-Rw Drive mounted):

******************************************

Disk Mounter 2.20 Error:
 Mount CD Rom 1 (not mounted)
  Unable to mount the selected volume. mount: special device /dev/hdd does not exist
  Mount CD Rom 2 (not mounted)
  Unable to mount the selected volume. mount: special device /dev/hdd does not exist

************************
When attempting to burn disk in Serpentine, Serpentine locks up up at fixating disk.

Error Message says to try a lower speed. Serpentine program froze. CD would not eject. I had to reboot. Reattempts at lower speeds did not resolve issue.

****************************
K3B makes it through all the preparations but stops when it begins to write. The K3B Debugging Output reads

K3b Version: 1.0.3
KDE Version: 3.5.8
QT Version: 3.3.7
Kernel: 2.6.22-15-generic
Devices
-----------------------
LITEON CD-ROM LTN526D YSR7 (/dev/scd1, ) [CD-ROM] [CD-ROM] [None]

ATAPI CD-RW 52X24 K.FC (/dev/scd0, ) [CD-R, CD-RW, CD-ROM] [CD-ROM, CD-R, CD-RW] [SAO, TAO, RAW, SAO/R96P, SAO/R96R, RAW/R16, RAW/R96P, RAW/R96R]
Used versions
-----------------------
cdrecord: 1.1.6

cdrecord
-----------------------
/usr/bin/wodim: Operation not permitted. Warning: Cannot raise RLIMIT_MEMLOCK limits.
scsidev: '/dev/scd0'
devname: '/dev/scd0'
scsibus: -2 target: -2 lun: -2
Linux sg driver version: 3.5.27
Wodim version: 1.1.6
SCSI buffer size: 64512
Beginning DMA speed test. Set CDR_NODMATEST environment variable if device
communication breaks or freezes immediately after that.
TOC Type: 0 = CD-DA
Driveropts: 'burnfree'
Device type : Removable CD-ROM
Version : 5
Response Format: 2
Capabilities :
Vendor_info : 'ATAPI '
Identification : 'CD-RW 52X24 '
Revision : 'K.FC'
Device seems to be: Generic mmc CD-RW.
Current: 0x0009 (CD-R)
Profile: 0x000A (CD-RW)
Profile: 0x0009 (CD-R) (current)
Profile: 0x0008 (CD-ROM)
Profile: 0x0002 (Removable disk) (current)
Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
Driver flags : MMC-3 SWABAUDIO BURNFREE FORCESPEED
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R
Drive buf size : 1961344 = 1915 KB
FIFO size : 12582912 = 12288 KB
Encoding speed : 297x (22262 sectors/s) for libedc from Heiko Eißfeldt
pregap1: -1
Track 01: audio 33 MB (03:20.26) no preemp
Track 02: audio 53 MB (05:17.74) no preemp pregapsize: 0
.
.
.

Speed set to 9173 KB/s
Total size: 660 MB (65:27.80) = 294585 sectors
Lout start: 661 MB (65:29/60) = 294585 sectors
Current Secsize: 2048
ATIP info from disk:
  Indicated writing power: 5
  Is not unrestricted
  Is not erasable
  Disk sub type: Medium Type B, low Beta category (B-) (4)
  ATIP start of lead in: -12369 (97:17/06)
  ATIP start of lead out: 359849 (79:59/74)
Disk type: Short strategy type (Phthalocyanine or similar)
Manuf. index: 69
Manufacturer: Moser Baer India Limited
Manufacturer is guessed because of the orange forum embargo.
The orange forum likes to get money for recent information.
The information for this media may not be correct.
Blocks total: 359849 Blocks current: 359849 Blocks remaining: 65264
Forcespeed is OFF.
Starting to write CD/DVD at speed 52.0 in real RAW/RAW96R mode for single session.
Last chance to quit, starting real write in 2 seconds.
   1 seconds.
   0 seconds.
 Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
Performing OPC...
/usr/bin/wodim: WARNING: Drive returns wrong startsec (0) using -12369 from ATIP
Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error
CDB: 2A 00 FF FF D2 05 00 00 1A 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 72 0B 00 00 00 00 00 0E 09 0C 00 00 00 02 00 00
Sense Key: 0x0 No Additional Sense, Segment 11
Sense Code: 0x00 Qual 0x02 (end-of-partition/medium detected) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 56.628s timeout 40s
/usr/bin/wodim: Could not write Lead-in.
Errno: 5 (Input/output error), start/stop unit scsi sendcmd: no error
CDB: 1B 00 00 00 02 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 02 00 00 00 00 0A 00 00 00 00 04 07 00 00
Sense Key: 0x2 Not Ready, Segment 0
Sense Code: 0x04 Qual 0x07 (logical unit not ready, operation in progress) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.001s timeout 40s
/usr/bin/wodim: Cannot eject media.
Writing lead-in at sector -12369
write leadin data: error after 1463904 bytes
Writing time: 66.590s
/usr/bin/wodim: fifo had 192 puts and 0 gets.
/usr/bin/wodim: fifo was 0 times empty and 0 times full, min fill was 100%.
BURN-Free was never needed.

cdrecord command:
-----------------------
/usr/bin/wodim -v gracetime=2 dev=/dev/scd0 speed=52 -raw96r driveropts=burnfree -eject -text -useinfo -audio -shorttrack /tmp/kde-kace/k3bCdCopy0/Track01.wav /

kace@The:~$ uname -r
2.6.22-15-generic
kace@The:~$ dmesg
[ 0.000000] Linux version 2.6.22-15-generic (buildd@terranova) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Fri Jul 11 19:25:33 UTC 2008 (Ubuntu 2.6.22-15.56-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 0000000015ff0000 (usable)
[ 0.000000] BIOS-e820: 0000000015ff0000 - 0000000015ff8000 (ACPI data)
[ 0.000000] BIOS-e820: 0000000015ff8000 - 0000000016000000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000ffee0000 - 00000000fff00000 (reserved)
[ 0.000000] BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 351MB LOWMEM available.
[ 0.000000] Entering add_active_range(0, 0, 90096) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 90096
[ 0.000000] HighMem 90096 -> 90096
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 90096
[ 0.000000] On node 0 totalpages: 90096
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 671 pages used for memmap
[ 0.000000] Normal zone: 85329 pages, LIFO batch:15
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP signature @ 0xC00FA2E0 checksum 0
[ 0.000000] ACPI: RSDP 000FA2E0, 0014 (r0 AMI )
[ 0.000000] ACPI: RSDT 15FF0000, 0028 (r1 AMIINT SiS740XX 1000 MSFT 100000B)
[ 0.000000] ACPI: FACP 15FF0030, 0081 (r2 AMIINT SiS740XX 11 MSFT 100000B)
[ 0.000000] ACPI: DSDT 15FF00C0, 32A6 (r1 SiS 740 100 MSFT 100000D)
[ 0.000000] ACPI: FACS 15FF8000, 0040
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] Allocating PCI resources starting at 20000000 (gap: 16000000:e9ee0000)
[ 0.000000] Built 1 zonelists. Total pages: 89393
[ 0.000000] Kernel command line: root=UUID=e988f638-69d4-49d7-aaf8-ef582ed7ccc8 ro quiet splash
[ 0.000000] Local APIC disabled by BIOS -- you can enable it with "lapic"
[ 0.000000] mapped APIC to ffffd000 (012cd000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 0.000000] Detected 995.833 MHz processor.
[ 20.462573] Console: colour VGA+ 80x25
[ 20.463622] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 20.464361] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 20.492169] Memory: 345612k/360384k available (2016k kernel code, 14216k reserved, 919k data, 364k init, 0k highmem)
[ 20.492193] virtual kernel memory layout:
[ 20.492195] fixmap : 0xfff4d000 - 0xfffff000 ( 712 kB)
[ 20.492198] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 20.492201] vmalloc : 0xd6800000 - 0xff7fe000 ( 655 MB)
[ 20.492204] lowmem : 0xc0000000 - 0xd5ff0000 ( 351 MB)
[ 20.492207] .init : 0xc03e3000 - 0xc043e000 ( 364 kB)
[ 20.492210] .data : 0xc02f8046 - 0xc03dde84 ( 919 kB)
[ 20.492213] .text : 0xc0100000 - 0xc02f8046 (2016 kB)
[ 20.492221] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 20.492324] SLUB: Genslabs=22, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
[ 20.572334] Calibrating delay using timer specific routine.. 1993.16 BogoMIPS (lpj=3986329)
[ 20.572404] Security Framework v1.0.0 initialized
[ 20.572422] SELinux: Disabled at boot.
[ 20.572465] Mount-cache hash table entries: 512
[ 20.572787] CPU: After generic identify, caps: 0183f9ff c1c7f9ff 00000000 00000000 00000000 00000000 00000000
[ 20.572807] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 20.572814] CPU: L2 Cache: 256K (64 bytes/line)
[ 20.572821] CPU: After all inits, caps: 0183f9ff c1c7f9ff 00000000 00000420 00000000 00000000 00000000
[ 20.572845] Compat vDSO mapped to ffffe000.
[ 20.572876] Checking 'hlt' instruction... OK.
[ 20.588408] SMP alternatives: switching to UP code
[ 20.589001] Freeing SMP alternatives: 11k freed
[ 20.589826] Early unpacking initramfs... done
[ 21.255630] ACPI: Core revision 20070126
[ 21.255867] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[ 21.258425] ACPI: setting ELCR to 0200 (from 0820)
[ 21.259269] CPU0: AMD Athlon(tm) Processor stepping 04
[ 21.259282] SMP motherboard not detected.
[ 21.259288] Local APIC not detected. Using dummy APIC emulation.
[ 21.259398] Brought up 1 CPUs
[ 21.259761] Booting paravirtualized kernel on bare hardware
[ 21.259906] Time: 14:38:34 Date: 06/24/108
[ 21.259985] NET: Registered protocol family 16
[ 21.260256] EISA bus registered
[ 21.260280] ACPI: bus type pci registered
[ 21.262389] PCI: PCI BIOS revision 2.10 entry at 0xfdb01, last bus=2
[ 21.262395] Setting up standard PCI resources
[ 21.265947] ACPI: EC: Look up EC in DSDT
[ 21.272039] ACPI: Interpreter enabled
[ 21.272047] ACPI: (supports S0 S1 S4 S5)
[ 21.272078] ACPI: Using PIC for interrupt routing
[ 21.281870] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 21.281890] PCI: Probing PCI hardware (bus 00)
[ 21.282228] Enabling SiS 96x SMBus.
[ 21.283164] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 21.285909] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 21.286101] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 7 10 11 12 14 15)
[ 21.286283] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 *11 12 14 15)
[ 21.286461] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 10 11 12 14 15)
[ 21.286638] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 *11 12 14 15)
[ 21.286816] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 7 10 11 12 14 15)
[ 21.286992] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 *11 12 14 15)
[ 21.287169] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 7 10 11 12 14 15)
[ 21.287365] ACPI: Power Resource [URP1] (off)
[ 21.287422] ACPI: Power Resource [URP2] (off)
[ 21.287477] ACPI: Power Resource [FDDP] (off)
[ 21.287531] ACPI: Power Resource [LPTP] (off)
[ 21.287552] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 21.287598] pnp: PnP ACPI init
[ 21.287617] ACPI: bus type pnp registered
[ 21.293852] pnp: PnP ACPI: found 12 devices
[ 21.293858] ACPI: ACPI bus type pnp unregistered
[ 21.293869] PnPBIOS: Disabled by ACPI PNP
[ 21.294011] PCI: Using ACPI for IRQ routing
[ 21.294019] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 21.298656] NET: Registered protocol family 8
[ 21.298661] NET: Registered protocol family 20
[ 21.300127] Time: tsc clocksource has been installed.
[ 21.329500] PCI: Bridge: 0000:00:01.0
[ 21.329507] IO window: a000-afff
[ 21.329518] MEM window: cfd00000-cfefffff
[ 21.329526] PREFETCH window: bfa00000-cfbfffff
[ 21.329570] NET: Registered protocol family 2
[ 21.368272] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 21.368420] TCP established hash table entries: 16384 (order: 5, 196608 bytes)
[ 21.369243] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[ 21.370006] TCP: Hash tables configured (established 16384 bind 16384)
[ 21.370013] TCP reno registered
[ 21.380493] checking if image is initramfs...<6>Switched to high resolution mode on CPU 0
[ 21.944239] it is
[ 22.644454] Freeing initrd memory: 7117k freed
[ 22.645431] audit: initializing netlink socket (disabled)
[ 22.645467] audit(1216910314.812:1): initialized
[ 22.649431] VFS: Disk quotas dquot_6.5.1
[ 22.649567] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 22.649801] io scheduler noop registered
[ 22.649807] io scheduler anticipatory registered
[ 22.649811] io scheduler deadline registered
[ 22.649838] io scheduler cfq registered (default)
[ 22.649948] Boot video device is 0000:01:00.0
[ 22.650337] isapnp: Scanning for PnP cards...
[ 23.004367] isapnp: No Plug & Play device found
[ 23.065480] Real Time Clock Driver v1.12ac
[ 23.065698] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 23.065889] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 23.067690] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 23.068683] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
[ 23.068691] PCI: setting IRQ 5 as level-triggered
[ 23.068697] ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
[ 23.071463] 0000:00:09.0: ttyS1 at I/O 0xd028 (irq = 5) is a 8250
[ 23.073085] 0000:00:09.0: ttyS2 at I/O 0xd040 (irq = 5) is a 8250
[ 23.074090] 0000:00:09.0: ttyS3 at I/O 0xd050 (irq = 5) is a 8250
[ 23.074390] Couldn't register serial port 0000:00:09.0: -28
[ 23.075768] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 23.076320] input: Macintosh mouse button emulation as /class/input/input0
[ 23.076526] PNP: PS/2 Controller [PNP030b:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 23.076983] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 23.076995] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 23.077349] mice: PS/2 mouse device common for all mice
[ 23.077592] EISA: Probing bus 0 at eisa.0
[ 23.077652] EISA: Detected 0 cards.
[ 23.078232] TCP cubic registered
[ 23.078254] NET: Registered protocol family 1
[ 23.078302] Using IPI No-Shortcut mode
[ 23.078739] Magic number: 0:874:637
[ 23.080571] Freeing unused kernel memory: 364k freed
[ 23.111745] input: AT Translated Set 2 keyboard as /class/input/input1
[ 24.543775] AppArmor: AppArmor initialized<5>audit(1216910316.812:2): type=1505 info="AppArmor initialized" pid=1201
[ 24.558591] fuse init (API version 7.8)
[ 24.569767] Failure registering capabilities with primary security module.
[ 25.933526] usbcore: registered new interface driver usbfs
[ 25.933594] usbcore: registered new interface driver hub
[ 25.933647] usbcore: registered new device driver usb
[ 25.935628] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 25.936107] ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11
[ 25.936116] PCI: setting IRQ 11 as level-triggered
[ 25.936122] ACPI: PCI Interrupt 0000:00:03.0[A] -> Link [LNKE] -> GSI 11 (level, low) -> IRQ 11
[ 25.936153] ohci_hcd 0000:00:03.0: OHCI Host Controller
[ 25.936537] ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
[ 25.936578] ohci_hcd 0000:00:03.0: irq 11, io mem 0xcfff9000
[ 25.998818] SCSI subsystem initialized
[ 26.009604] libata version 2.21 loaded.
[ 26.031667] usb usb1: configuration #1 chosen from 1 choice
[ 26.031741] hub 1-0:1.0: USB hub found
[ 26.031766] hub 1-0:1.0: 2 ports detected
[ 26.135330] ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 5
[ 26.135345] ACPI: PCI Interrupt 0000:00:03.1[B] -> Link [LNKF] -> GSI 5 (level, low) -> IRQ 5
[ 26.135383] ohci_hcd 0000:00:03.1: OHCI Host Controller
[ 26.135441] ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
[ 26.135481] ohci_hcd 0000:00:03.1: irq 5, io mem 0xcfffa000
[ 26.192856] usb usb2: configuration #1 chosen from 1 choice
[ 26.192929] hub 2-0:1.0: USB hub found
[ 26.192961] hub 2-0:1.0: 2 ports detected
[ 26.217036] sis900.c: v1.08.10 Apr. 2 2006
[ 26.295300] ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 11
[ 26.295313] ACPI: PCI Interrupt 0000:00:03.2[C] -> Link [LNKG] -> GSI 11 (level, low) -> IRQ 11
[ 26.295356] ohci_hcd 0000:00:03.2: OHCI Host Controller
[ 26.295418] ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3
[ 26.295456] ohci_hcd 0000:00:03.2: irq 11, io mem 0xcfffb000
[ 26.310794] Floppy drive(s): fd0 is 1.44M
[ 26.352817] usb usb3: configuration #1 chosen from 1 choice
[ 26.352895] hub 3-0:1.0: USB hub found
[ 26.352926] hub 3-0:1.0: 2 ports detected
[ 26.441454] FDC 0 is a post-1991 82077
[ 26.461067] pata_sis 0000:00:02.5: version 0.5.1
[ 26.461527] scsi0 : pata_sis
[ 26.461657] scsi1 : pata_sis
[ 26.461874] ata1: PATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001ff00 irq 14
[ 26.461882] ata2: PATA max UDMA/133 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001ff08 irq 15
[ 26.632300] ata1.00: ATA-7: WDC WD1600AAJB-00PVA0, 00.07H00, max UDMA/100
[ 26.632312] ata1.00: 312581808 sectors, multi 16: LBA48
[ 26.638962] ata1.00: configured for UDMA/100
[ 27.282428] ata2.00: ATAPI: CD-RW 52X24, K.FC, max UDMA/33
[ 27.282447] ata2.01: ATAPI: LTN526D, YSR7, max UDMA/33
[ 27.454376] ata2.00: configured for UDMA/33
[ 27.626328] ata2.01: configured for UDMA/33
[ 27.626672] scsi 0:0:0:0: Direct-Access ATA WDC WD1600AAJB-0 00.0 PQ: 0 ANSI: 5
[ 27.629344] scsi 1:0:0:0: CD-ROM ATAPI CD-RW 52X24 K.FC PQ: 0 ANSI: 5
[ 27.630690] scsi 1:0:1:0: CD-ROM LITEON CD-ROM LTN526D YSR7 PQ: 0 ANSI: 5
[ 27.632019] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 5
[ 27.632031] ACPI: PCI Interrupt 0000:00:03.3[D] -> Link [LNKH] -> GSI 5 (level, low) -> IRQ 5
[ 27.632060] ehci_hcd 0000:00:03.3: EHCI Host Controller
[ 27.632514] ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 4
[ 27.632603] PCI: cache line size of 64 is not supported by device 0000:00:03.3
[ 27.632624] ehci_hcd 0000:00:03.3: irq 5, io mem 0xcffdf000
[ 27.632639] ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 27.633380] usb usb4: configuration #1 chosen from 1 choice
[ 27.633680] hub 4-0:1.0: USB hub found
[ 27.633698] hub 4-0:1.0: 6 ports detected
[ 27.674099] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 27.674202] sd 0:0:0:0: [sda] Write Protect is off
[ 27.674209] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 27.674246] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 27.674415] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 27.674437] sd 0:0:0:0: [sda] Write Protect is off
[ 27.674443] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 27.674471] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 27.674484] sda: sda1 sda2 < sda5 sda6 sda7 > sda3
[ 27.711026] sd 0:0:0:0: [sda] Attached SCSI disk
[ 27.719926] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 27.719974] scsi 1:0:0:0: Attached scsi generic sg1 type 5
[ 27.720013] scsi 1:0:1:0: Attached scsi generic sg2 type 5
[ 27.735154] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
[ 27.735168] ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5
[ 27.736519] 0000:00:04.0: VIA 6103 PHY transceiver found at address 1.
[ 27.749946] 0000:00:04.0: Using transceiver found at address 1 as default
[ 27.751072] eth0: SiS 900 PCI Fast Ethernet at 0xd400, IRQ 5, 00:0a:e6:50:d7:cf.
[ 27.836636] sr0: scsi3-mmc drive: 52x/52x writer cd/rw xa/form2 cdda tray
[ 27.836653] Uniform CD-ROM driver Revision: 3.20
[ 27.837382] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 27.842899] sr1: scsi3-mmc drive: 52x/52x cd/rw xa/form2 cdda tray
[ 27.843606] sr 1:0:1:0: Attached scsi CD-ROM sr1
[ 28.294934] Attempting manual resume
[ 28.294945] swsusp: Resume From Partition 8:7
[ 28.294948] PM: Checking swsusp image.
[ 28.300505] PM: Resume from disk failed.
[ 28.352237] kjournald starting. Commit interval 5 seconds
[ 28.352269] EXT3-fs: mounted filesystem with ordered data mode.
[ 35.380620] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 35.504420] Netfilter messages via NETLINK v0.30.
[ 35.513744] nf_conntrack version 0.5.0 (2815 buckets, 22520 max)
[ 39.754337] Linux agpgart interface v0.102 (c) Dave Jones
[ 39.764547] agpgart: Detected SiS chipset - id:1856
[ 39.772045] agpgart: AGP aperture is 64M @ 0xd0000000
[ 39.879379] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 40.082612] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 40.108948] sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0x0c00
[ 41.169365] input: PC Speaker as /class/input/input2
[ 42.416870] input: ImPS/2 Logitech Wheel Mouse as /class/input/input3
[ 42.628840] parport_pc 00:09: reported by Plug and Play ACPI
[ 42.628966] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 43.090873] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
[ 43.090887] ACPI: PCI Interrupt 0000:00:02.7[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
[ 43.412742] intel8x0_measure_ac97_clock: measured 55570 usecs
[ 43.412752] intel8x0: clocking to 48000
[ 44.266308] lp0: using parport0 (interrupt-driven).
[ 44.370760] Adding 899568k swap on /dev/sda7. Priority:-1 extents:1 across:899568k
[ 44.723816] EXT3 FS on sda3, internal journal
[ 48.249290] No dock devices found.
[ 48.495121] input: Power Button (FF) as /class/input/input4
[ 48.495829] ACPI: Power Button (FF) [PWRF]
[ 48.527110] input: Power Button (CM) as /class/input/input5
[ 48.527811] ACPI: Power Button (CM) [PWRB]
[ 48.543113] input: Sleep Button (CM) as /class/input/input6
[ 48.543827] ACPI: Sleep Button (CM) [SLPB]
[ 49.175749] powernow: No powernow capabilities detected
[ 53.812402] Failure registering capabilities with primary security module.
[ 54.258070] eth0: Media Link On 100mbps full-duplex
[ 54.647828] ppdev: user-space parallel port driver
[ 55.356901] audit(1216910348.236:3): type=1503 operation="inode_permission" requested_mask="a" denied_mask="a" name="/dev/tty" pid=5175 profile="/usr/sbin/cupsd"
[ 55.572989] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 55.573018] apm: overridden by ACPI.
[ 56.312397] Installing knfsd (copyright (C) 1996 <email address hidden>).
[ 57.085549] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 57.111846] NFSD: starting 90-second grace period
[ 66.036962] Bluetooth: Core ver 2.11
[ 66.037508] NET: Registered protocol family 31
[ 66.037515] Bluetooth: HCI device and connection manager initialized
[ 66.037529] Bluetooth: HCI socket layer initialized
[ 66.235237] Bluetooth: L2CAP ver 2.8
[ 66.235261] Bluetooth: L2CAP socket layer initialized
[ 66.377025] Bluetooth: RFCOMM socket layer initialized
[ 66.377392] Bluetooth: RFCOMM TTY layer initialized
[ 66.377398] Bluetooth: RFCOMM ver 1.8
[ 68.630739] NET: Registered protocol family 17
[ 72.813433] NET: Registered protocol family 10
[ 72.814074] lo: Disabled Privacy Extensions
[ 83.123480] eth0: no IPv6 routers present
[ 7062.959247] usb 4-2: new high speed USB device using ehci_hcd and address 2
[ 7063.092141] usb 4-2: configuration #1 chosen from 1 choice
[ 7063.092387] hub 4-2:1.0: USB hub found
[ 7063.092558] hub 4-2:1.0: 2 ports detected
[ 7064.091056] usb 4-2.1: new high speed USB device using ehci_hcd and address 3
[ 7064.184478] usb 4-2.1: configuration #1 chosen from 1 choice
[ 7064.485405] /build/buildd/linux-source-2.6.22-2.6.22/drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 3 if 0 alt 0 proto 2 vid 0x03F0 pid 0x7B04
[ 7064.486899] usbcore: registered new interface driver usblp
[ 7064.487312] /build/buildd/linux-source-2.6.22-2.6.22/drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[ 7146.950392] /build/buildd/linux-source-2.6.22-2.6.22/drivers/usb/class/usblp.c: usblp0: removed
[ 7148.685714] audit(1216917442.826:4): type=1503 operation="inode_permission" requested_mask="rw" denied_mask="rw" name="/dev/tty" pid=7249 profile="/usr/sbin/cupsd"
[ 7149.743223] audit(1216917443.826:5): type=1503 operation="inode_permission" requested_mask="rw" denied_mask="rw" name="/dev/tty" pid=7252 profile="/usr/sbin/cupsd"
[ 7358.732803] audit(1216917652.838:6): type=1503 operation="inode_permission" requested_mask="rw" denied_mask="rw" name="/dev/tty" pid=8234 profile="/usr/sbin/cupsd"
[ 7359.495345] audit(1216917653.838:7): type=1503 operation="inode_permission" requested_mask="rw" denied_mask="rw" name="/dev/tty" pid=8247 profile="/usr/sbin/cupsd"
[ 7514.299351] audit(1216917808.847:8): type=1503 operation="inode_permission" requested_mask="rw" denied_mask="rw" name="/dev/tty" pid=9468 profile="/usr/sbin/cupsd"
[ 7514.600510] audit(1216917808.847:9): type=1503 operation="inode_permission" requested_mask="rw" denied_mask="rw" name="/dev/tty" pid=9483 profile="/usr/sbin/cupsd"
[ 9375.007077] audit(1216919669.953:10): type=1503 operation="inode_permission" requested_mask="rw" denied_mask="rw" name="/dev/tty" pid=10586 profile="/usr/sbin/cupsd"
[ 9375.400655] audit(1216919670.453:11): type=1503 operation="inode_permission" requested_mask="rw" denied_mask="rw" name="/dev/tty" pid=10589 profile="/usr/sbin/cupsd"
[ 9490.555090] audit(1216919785.459:12): type=1503 operation="inode_permission" requested_mask="rw" denied_mask="rw" name="/dev/tty" pid=13019 profile="/usr/sbin/cupsd"
[ 9490.701596] audit(1216919785.959:13): type=1503 operation="inode_permission" requested_mask="rw" denied_mask="rw" name="/dev/tty" pid=13022 profile="/usr/sbin/cupsd"
[ 9548.189940] audit(1216919843.463:14): type=1503 operation="inode_permission" requested_mask="rw" denied_mask="rw" name="/dev/tty" pid=14074 profile="/usr/sbin/cupsd"
[ 9548.330596] audit(1216919843.463:15): type=1503 operation="inode_permission" requested_mask="rw" denied_mask="rw" name="/dev/tty" pid=14077 profile="/usr/sbin/cupsd"
[11707.705003] audit(1216922003.586:16): type=1503 operation="inode_permission" requested_mask="rw" denied_mask="rw" name="/dev/tty" pid=17843 profile="/usr/sbin/cupsd"
[11707.993449] audit(1216922003.586:17): type=1503 operation="inode_permission" requested_mask="rw" denied_mask="rw" name="/dev/tty" pid=17846 profile="/usr/sbin/cupsd"
[11748.099935] audit(1216922044.088:18): type=1503 operation="inode_permission" requested_mask="rw" denied_mask="rw" name="/dev/tty" pid=19143 profile="/usr/sbin/cupsd"
[11748.529839] audit(1216922044.088:19): type=1503 operation="inode_permission" requested_mask="rw" denied_mask="rw" name="/dev/tty" pid=19158 profile="/usr/sbin/cupsd"
[11848.547004] audit(1216922144.594:20): type=1503 operation="inode_permission" requested_mask="rw" denied_mask="rw" name="/dev/tty" pid=20274 profile="/usr/sbin/cupsd"
[11848.890574] audit(1216922144.594:21): type=1503 operation="inode_permission" requested_mask="rw" denied_mask="rw" name="/dev/tty" pid=20289 profile="/usr/sbin/cupsd"
[12063.168672] audit(1216922359.106:22): type=1503 operation="inode_permission" requested_mask="rw" denied_mask="rw" name="/dev/tty" pid=21509 profile="/usr/sbin/cupsd"
[12063.513205] audit(1216922359.606:23): type=1503 operation="inode_permission" requested_mask="rw" denied_mask="rw" name="/dev/tty" pid=21519 profile="/usr/sbin/cupsd"
[15863.067737] end_request: I/O error, dev sr1, sector 0
[15863.067770] Buffer I/O error on device sr1, logical block 0
[15863.067788] Buffer I/O error on device sr1, logical block 1
[15863.067795] Buffer I/O error on device sr1, logical block 2
[15863.067802] Buffer I/O error on device sr1, logical block 3
[15863.070942] end_request: I/O error, dev sr1, sector 0
[15863.070951] Buffer I/O error on device sr1, logical block 0
[15863.072407] end_request: I/O error, dev sr1, sector 0
[15863.072414] Buffer I/O error on device sr1, logical block 0
[15863.073803] end_request: I/O error, dev sr1, sector 0
[15863.073811] Buffer I/O error on device sr1, logical block 0
[15863.075274] end_request: I/O error, dev sr1, sector 0
[15863.075282] Buffer I/O error on device sr1, logical block 0
[15863.076708] end_request: I/O error, dev sr1, sector 0
[15863.076717] Buffer I/O error on device sr1, logical block 0
[16270.207255] cdrom: This disc doesn't have any tracks I recognize!
[17697.648492] cdrom: This disc doesn't have any tracks I recognize!
[18076.667858] cdrom: This disc doesn't have any tracks I recognize!
[18156.876079] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
[18156.876117] ata2.00: cmd a0/00:00:00:00:20/00:00:00:00:00/a0 tag 0 cdb 0x1b data 0
[18156.876122] res 40/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
[18161.914315] ata2: port is slow to respond, please be patient (Status 0xd0)
[18166.896646] ata2: device not ready (errno=-16), forcing hardreset
[18166.896676] ata2: soft resetting port
[18167.744694] ata2.00: configured for UDMA/33
[18167.908784] ata2.01: configured for UDMA/33
[18167.908900] ata2: EH complete
[22829.194865] audit(1216933128.720:24): type=1503 operation="inode_permission" requested_mask="rw" denied_mask="rw" name="/dev/tty" pid=23360 profile="/usr/sbin/cupsd"
[22829.932955] audit(1216933129.220:25): type=1503 operation="inode_permission" requested_mask="rw" denied_mask="rw" name="/dev/tty" pid=23366 profile="/usr/sbin/cupsd"
kace@The:~$

********************************************************8

K3B crashed while I was attempting to repeat burn session with a new disk.

K3b-The KDE Crash Handler reported:
K3B crashed and caused a signal 11 (SIGE0GV).
Said, the SIGEGV signal may be due to a bug in the application. (see http://bugs.kde.org)
K3b Backtrace read
This backtrace appears to be of no use.
This is probably because your packages are built in a way which prevents creation of proper backtraces, or the stack frame was seriously corrupted in the crash.

(no debugging symbols found)
Using host libthread_db library "/lib/tls/i686/cmov/libthread_db.so.1".

****************************************************

Attempt to burn audio test Succeeded when using Rewritable Disks (MEMOREX 12x 700MB 80 min Rewritable Disk)

WestCoast (fayemore-yahoo) wrote :
Download full text (4.0 KiB)

This was the debugging output from a successful k3b copy cd onto a cd rewriteable disk.

Although this was a successful burn K3B debugging noted usr/bin/wodim: Operation not permitted. Warning: Cannot raise RLIMIT_MEMLOCK limits. Is this a problem?

Also, I attempted to Launch the Bug Report Wizard from the Submit a Bug Report - K3b window. However, an error message appears stating, "Could not Launch the Browser. Could not find service, kfmclient.

The following was produced by the K3b Debugging

System
-----------------------
K3b Version: 1.0.3

KDE Version: 3.5.8
QT Version: 3.3.7
Kernel: 2.6.22-15-generic
Devices
-----------------------
LITEON CD-ROM LTN526D YSR7 (/dev/scd1, ) [CD-ROM] [CD-ROM] [None]

ATAPI CD-RW 52X24 K.FC (/dev/scd0, ) [CD-R, CD-RW, CD-ROM] [CD-ROM, CD-R, CD-RW] [SAO, TAO, RAW, SAO/R96P, SAO/R96R, RAW/R16, RAW/R96P, RAW/R96R]
K3bDataTrackReader
-----------------------
reading sectors 0 to 2038 with sector size 2048. Length: 2039 sectors, 4175872 bytes.
using buffer size of 64 blocks.
Read a total of 2039 sectors (4175872 bytes)

Used versions
-----------------------
cdrecord: 1.1.6

cdrecord
-----------------------
/usr/bin/wodim: Operation not permitted. Warning: Cannot raise RLIMIT_MEMLOCK limits.
scsidev: '/dev/scd0'
devname: '/dev/scd0'
scsibus: -2 target: -2 lun: -2
Linux sg driver version: 3.5.27
Wodim version: 1.1.6
SCSI buffer size: 64512
Beginning DMA speed test. Set CDR_NODMATEST environment variable if device
communication breaks or freezes immediately after that.
TOC Type: 1 = CD-ROM
Driveropts: 'burnfree'
Device type : Removable CD-ROM
Version : 5
Response Format: 2
Capabilities :
Vendor_info : 'ATAPI '
Identification : 'CD-RW 52X24 '
Revision : 'K.FC'
Device seems to be: Generic mmc CD-RW.
Current: 0x000A (CD-RW)
Profile: 0x000A (CD-RW) (current)
Profile: 0x0009 (CD-R)
Profile: 0x0008 (CD-ROM)
Profile: 0x0002 (Removable disk) (current)
Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
Driver flags : MMC-3 SWABAUDIO BURNFREE FORCESPEED
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R
Drive buf size : 1961344 = 1915 KB
FIFO size : 12582912 = 12288 KB
Speed set to 2117 KB/s
Track 01: data 3 MB
Total size: 4 MB (00:27.18) = 2039 sectors
Lout start: 4 MB (00:29/14) = 2039 sectors
Current Secsize: 2048
ATIP info from disk:
  Indicated writing power: 3
  Reference speed: 6
  Is not unrestricted
  Is erasable
  Disk sub type: High speed Rewritable (CAV) media (1)
  ATIP start of lead in: -11745 (97:25/30)
  ATIP start of lead out: 359848 (79:59/73)
  1T speed low: 4 1T speed high: 10
  2T speed low: 4 2T speed high: 0 (reserved val 6)
  power mult factor: 1 5
  recommended erase/write power: 5
  A1 values: 24 1A D8
  A2 values: 26 B2 4A
Disk type: Phase change
Manuf. index: 40
Manufacturer: INFODISC Technology Co., Ltd.
Blocks total: 359848 Blocks current: 359848 Blocks remaining: 357809
Forcespeed is OFF.
Starting to write CD/DVD at speed 12.0 in real SAO mode for single session.
Last chance to quit, starting real write in 2 seconds.
   1 seconds.
   0 seconds.
 Operation starts.
Waiting for read...

Read more...

To post a comment you must log in.
This report contains Public information  Edit
Everyone can see this information.

Other bug subscribers