[ 27.958476] input: lircd as /devices/virtual/input/input12 [ 28.340995] i2c-adapter i2c-2: unable to read EDID block. [ 28.340999] i915 0000:00:02.0: DVI-D-1: no EDID data [ 28.459461] i2c-adapter i2c-2: unable to read EDID block. [ 28.459465] i915 0000:00:02.0: DVI-D-1: no EDID data [ 28.614264] [drm] TV-10: set mode NTSC 480i 0 [ 28.755046] [drm] TV-10: set mode NTSC 480i 0 [ 28.998776] i2c-adapter i2c-2: unable to read EDID block. [ 28.998780] i915 0000:00:02.0: DVI-D-1: no EDID data [ 29.105415] sky2 eth2: Link is up at 100 Mbps, full duplex, flow control both [ 29.115479] ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready [ 29.127117] i2c-adapter i2c-2: unable to read EDID block. [ 29.127120] i915 0000:00:02.0: DVI-D-1: no EDID data [ 29.284348] [drm] TV-10: set mode NTSC 480i 0 [ 29.426401] [drm] TV-10: set mode NTSC 480i 0 [ 39.560025] eth2: no IPv6 routers present [ 53.263232] vboxdrv: Trying to deactivate the NMI watchdog permanently... [ 53.263238] vboxdrv: Successfully done. [ 53.263242] vboxdrv: Found 2 processor cores. [ 53.263396] vboxdrv: fAsync=0 offMin=0x5a0 offMax=0x2e8c [ 53.263473] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'. [ 53.263477] vboxdrv: Successfully loaded version 3.0.10 (interface 0x000e0001). [ 55.522403] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 55.522409] Bluetooth: BNEP filters: protocol multicast [ 55.654336] Bridge firewalling registered [ 56.481507] lp: driver loaded but no devices found [ 56.565400] ppdev: user-space parallel port driver [ 59.856946] i2c-adapter i2c-2: unable to read EDID block. [ 59.856950] i915 0000:00:02.0: DVI-D-1: no EDID data [ 59.976054] i2c-adapter i2c-2: unable to read EDID block. [ 59.976057] i915 0000:00:02.0: DVI-D-1: no EDID data [ 60.128665] [drm] TV-10: set mode NTSC 480i 0 [ 60.269026] [drm] TV-10: set mode NTSC 480i 0 [ 60.473435] i2c-adapter i2c-2: unable to read EDID block. [ 60.473440] i915 0000:00:02.0: DVI-D-1: no EDID data [ 60.591541] i2c-adapter i2c-2: unable to read EDID block. [ 60.591545] i915 0000:00:02.0: DVI-D-1: no EDID data [ 60.943821] [drm] TV-10: set mode NTSC 480i 0 [ 61.086263] [drm] TV-10: set mode NTSC 480i 0 [ 61.236874] i2c-adapter i2c-2: unable to read EDID block. [ 61.236878] i915 0000:00:02.0: DVI-D-1: no EDID data [ 61.355602] i2c-adapter i2c-2: unable to read EDID block. [ 61.355606] i915 0000:00:02.0: DVI-D-1: no EDID data [ 61.511812] [drm] TV-10: set mode NTSC 480i 0 [ 61.654663] [drm] TV-10: set mode NTSC 480i 0 [ 70.980883] i2c-adapter i2c-2: unable to read EDID block. [ 70.980888] i915 0000:00:02.0: DVI-D-1: no EDID data [ 71.104957] i2c-adapter i2c-2: unable to read EDID block. [ 71.104961] i915 0000:00:02.0: DVI-D-1: no EDID data [ 71.260899] [drm] TV-10: set mode NTSC 480i 0 [ 71.401669] [drm] TV-10: set mode NTSC 480i 0 [ 74.921767] i2c-adapter i2c-2: unable to read EDID block. [ 74.921772] i915 0000:00:02.0: DVI-D-1: no EDID data [ 75.040325] i2c-adapter i2c-2: unable to read EDID block. [ 75.040332] i915 0000:00:02.0: DVI-D-1: no EDID data [ 75.197573] [drm] TV-10: set mode NTSC 480i 0 [ 75.338464] [drm] TV-10: set mode NTSC 480i 0 [ 126.175073] process `skype.real' is using obsolete setsockopt SO_BSDCOMPAT [ 140.692052] usb 1-6: new high speed USB device using ehci_hcd and address 16 [ 140.855329] usb 1-6: configuration #1 chosen from 1 choice [ 141.004885] Initializing USB Mass Storage driver... [ 141.017810] scsi4 : SCSI emulation for USB Mass Storage devices [ 141.025071] usbcore: registered new interface driver usb-storage [ 141.025075] USB Mass Storage support registered. [ 141.026066] usb-storage: device found at 16 [ 141.026068] usb-storage: waiting for device to settle before scanning [ 146.027122] usb-storage: device scan complete [ 146.029304] scsi 4:0:0:0: Direct-Access HTC Android Phone 0100 PQ: 0 ANSI: 2 [ 146.030307] sd 4:0:0:0: Attached scsi generic sg2 type 0 [ 146.058564] sd 4:0:0:0: [sdb] Attached SCSI removable disk [ 153.568170] wlan0: authenticate with AP 02:1b:11:e2:71:7e [ 153.569915] wlan0: authenticated [ 153.569918] wlan0: associate with AP 02:1b:11:e2:71:7e [ 153.572224] wlan0: RX AssocResp from 02:1b:11:e2:71:7e (capab=0x411 status=0 aid=4) [ 153.572229] wlan0: associated [ 153.573096] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 154.298153] padlock: VIA PadLock not detected. [ 164.232154] wlan0: no IPv6 routers present [ 2568.269781] pidgin[2343] general protection ip:91e3fb sp:bfefa480 error:0 in libpurple.so.0.6.2[8ee000+f0000] [ 3422.773482] usbcore: deregistering interface driver snd-usb-audio [ 3430.602597] HDA Intel 0000:00:1b.0: PCI INT A disabled [ 3434.510735] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 3434.510842] HDA Intel 0000:00:1b.0: setting latency timer to 64 [ 3434.577104] hda_codec: STAC922x, Apple subsys_id=106b0800 [ 3434.585704] input: HDA Intel Line In at Ext Rear Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13 [ 3434.585845] input: HDA Intel HP Out at Ext Rear Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input14 [ 3441.210149] usbcore: registered new interface driver snd-usb-audio [ 4164.603611] usbcore: deregistering interface driver snd-usb-audio [ 4164.690286] HDA Intel 0000:00:1b.0: PCI INT A disabled [ 4164.712182] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 4164.712264] HDA Intel 0000:00:1b.0: setting latency timer to 64 [ 4164.772570] hda_codec: STAC922x, Apple subsys_id=106b0800 [ 4164.781796] input: HDA Intel Line In at Ext Rear Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input15 [ 4164.781935] input: HDA Intel HP Out at Ext Rear Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input16 [ 4164.978186] usbcore: registered new interface driver snd-usb-audio [ 5337.826232] i2c-adapter i2c-2: unable to read EDID block. [ 5337.826240] i915 0000:00:02.0: DVI-D-1: no EDID data [ 5337.946646] i2c-adapter i2c-2: unable to read EDID block. [ 5337.946652] i915 0000:00:02.0: DVI-D-1: no EDID data [ 5338.096956] [drm] TV-10: set mode NTSC 480i 0 [ 5338.237203] [drm] TV-10: set mode NTSC 480i 0