[ 0.000000] Linux version 2.6.24-16-generic (buildd@palmer) (gcc version 4.2.3 (Ubuntu 4.2.3-2ubuntu7)) #1 SMP Thu Apr 10 13:23:42 UTC 2008 (Ubuntu 2.6.24-16.30-generic) [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000007ff80000 (usable) [ 0.000000] BIOS-e820: 000000007ff80000 - 000000007ff8e000 (ACPI data) [ 0.000000] BIOS-e820: 000000007ff8e000 - 000000007ffe0000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000007ffe0000 - 0000000080000000 (reserved) [ 0.000000] BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved) [ 0.000000] 1151MB HIGHMEM available. [ 0.000000] 896MB LOWMEM available. [ 0.000000] found SMP MP-table at 000ff780 [ 0.000000] Entering add_active_range(0, 0, 524160) 0 entries of 256 used [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] Normal 4096 -> 229376 [ 0.000000] HighMem 229376 -> 524160 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0 -> 524160 [ 0.000000] On node 0 totalpages: 524160 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 [ 0.000000] Normal zone: 1760 pages used for memmap [ 0.000000] Normal zone: 223520 pages, LIFO batch:31 [ 0.000000] HighMem zone: 2303 pages used for memmap [ 0.000000] HighMem zone: 292481 pages, LIFO batch:31 [ 0.000000] Movable zone: 0 pages used for memmap [ 0.000000] DMI 2.4 present. [ 0.000000] ACPI: RSDP signature @ 0xC00FAF00 checksum 0 [ 0.000000] ACPI: RSDP 000FAF00, 0014 (r0 ACPIAM) [ 0.000000] ACPI: RSDT 7FF80000, 0040 (r1 A_M_I_ OEMRSDT 12000726 MSFT 97) [ 0.000000] ACPI: FACP 7FF80200, 0081 (r1 A_M_I_ OEMFACP 12000726 MSFT 97) [ 0.000000] ACPI: DSDT 7FF80590, 9560 (r1 A0543 A0543000 0 INTL 20060113) [ 0.000000] ACPI: FACS 7FF8E000, 0040 [ 0.000000] ACPI: APIC 7FF80390, 0080 (r1 A_M_I_ OEMAPIC 12000726 MSFT 97) [ 0.000000] ACPI: OEMB 7FF8E040, 0066 (r1 A_M_I_ AMI_OEM 12000726 MSFT 97) [ 0.000000] ACPI: HPET 7FF89AF0, 0038 (r1 A_M_I_ OEMHPET 12000726 MSFT 97) [ 0.000000] ACPI: MCFG 7FF89B30, 003C (r1 A_M_I_ OEMMCFG 12000726 MSFT 97) [ 0.000000] ACPI: SSDT 7FF8E0B0, 01C6 (r1 AMI CPU1PM 1 INTL 20060113) [ 0.000000] ACPI: SSDT 7FF8E280, 013A (r1 AMI CPU2PM 1 INTL 20060113) [ 0.000000] ACPI: PM-Timer IO Port: 0x808 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) [ 0.000000] Processor #0 6:15 APIC version 20 [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) [ 0.000000] Processor #1 6:15 APIC version 20 [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled) [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000 [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:7fb00000) [ 0.000000] swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000 [ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e4000 [ 0.000000] swsusp: Registered nosave memory region: 00000000000e4000 - 0000000000100000 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 520065 [ 0.000000] Kernel command line: root=UUID=9a036eac-db91-4a54-937f-2bf007e61459 ro splash ata4=noprobe [ 0.000000] mapped APIC to ffffb000 (fee00000) [ 0.000000] mapped IOAPIC to ffffa000 (fec00000) [ 0.000000] Enabling fast FPU save and restore... done. [ 0.000000] Enabling unmasked SIMD FPU exception support... done. [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes) [ 0.000000] Detected 3117.981 MHz processor. [ 23.401300] Console: colour VGA+ 80x25 [ 23.401303] console [tty0] enabled [ 23.403203] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 23.403413] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 23.457410] Memory: 2066340k/2096640k available (2157k kernel code, 29048k reserved, 998k data, 364k init, 1179136k highmem) [ 23.457450] virtual kernel memory layout: [ 23.457450] fixmap : 0xfff4b000 - 0xfffff000 ( 720 kB) [ 23.457451] pkmap : 0xff800000 - 0xffc00000 (4096 kB) [ 23.457451] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) [ 23.457452] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) [ 23.457453] .init : 0xc041b000 - 0xc0476000 ( 364 kB) [ 23.457453] .data : 0xc031b5a4 - 0xc0414dc4 ( 998 kB) [ 23.457454] .text : 0xc0100000 - 0xc031b5a4 (2157 kB) [ 23.457675] Checking if this processor honours the WP bit even in supervisor mode... Ok. [ 23.457766] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1 [ 23.457885] hpet clockevent registered [ 23.537782] Calibrating delay using timer specific routine.. 6239.73 BogoMIPS (lpj=12479472) [ 23.537855] Security Framework initialized [ 23.537887] SELinux: Disabled at boot. [ 23.537926] AppArmor: AppArmor initialized [ 23.537955] Failure registering capabilities with primary security module. [ 23.537989] Mount-cache hash table entries: 512 [ 23.538113] CPU: After generic identify, caps: bfebfbff 20000000 00000000 00000000 0000e3bd 00000000 00000001 00000000 [ 23.538119] monitor/mwait feature present. [ 23.538147] using mwait in idle threads. [ 23.538177] CPU: L1 I cache: 32K, L1 D cache: 32K [ 23.538227] CPU: L2 cache: 4096K [ 23.538255] CPU: Physical Processor ID: 0 [ 23.538283] CPU: Processor Core ID: 0 [ 23.538311] CPU: After all inits, caps: bfebfbff 20000000 00000000 00003940 0000e3bd 00000000 00000001 00000000 [ 23.538316] Compat vDSO mapped to ffffe000. [ 23.538353] Checking 'hlt' instruction... OK. [ 23.554028] SMP alternatives: switching to UP code [ 23.555047] Early unpacking initramfs... done [ 23.745896] ACPI: Core revision 20070126 [ 23.745958] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found. [ 23.760524] CPU0: Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06 [ 23.760611] SMP alternatives: switching to SMP code [ 23.761091] Booting processor 1/1 eip 3000 [ 23.771297] Initializing CPU#1 [ 23.849360] Calibrating delay using timer specific routine.. 6235.57 BogoMIPS (lpj=12471147) [ 23.849364] CPU: After generic identify, caps: bfebfbff 20000000 00000000 00000000 0000e3bd 00000000 00000001 00000000 [ 23.849367] monitor/mwait feature present. [ 23.849369] CPU: L1 I cache: 32K, L1 D cache: 32K [ 23.849370] CPU: L2 cache: 4096K [ 23.849371] CPU: Physical Processor ID: 0 [ 23.849372] CPU: Processor Core ID: 1 [ 23.849373] CPU: After all inits, caps: bfebfbff 20000000 00000000 00003940 0000e3bd 00000000 00000001 00000000 [ 23.849883] CPU1: Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06 [ 23.850161] Total of 2 processors activated (12475.30 BogoMIPS). [ 23.850326] ENABLING IO-APIC IRQs [ 23.850509] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 24.017135] APIC calibration not consistent with PM Timer: 119ms instead of 100ms [ 24.017169] APIC delta adjusted to PM-Timer: 2165127 (2598112) [ 24.017269] checking TSC synchronization [CPU#0 -> CPU#1]: passed. [ 24.037305] Brought up 2 CPUs [ 24.037350] CPU0 attaching sched-domain: [ 24.037351] domain 0: span 03 [ 24.037352] groups: 01 02 [ 24.037354] CPU1 attaching sched-domain: [ 24.037355] domain 0: span 03 [ 24.037356] groups: 02 01 [ 24.037498] net_namespace: 64 bytes [ 24.037532] Booting paravirtualized kernel on bare hardware [ 24.037830] Time: 15:15:52 Date: 05/18/08 [ 24.037874] NET: Registered protocol family 16 [ 24.038021] EISA bus registered [ 24.038051] ACPI: bus type pci registered [ 24.038218] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=5 [ 24.038247] PCI: Using configuration type 1 [ 24.038275] Setting up standard PCI resources [ 24.046715] ACPI: EC: Look up EC in DSDT [ 24.051608] ACPI: Interpreter enabled [ 24.051637] ACPI: (supports S0 S1 S3 S4 S5) [ 24.051783] ACPI: Using IOAPIC for interrupt routing [ 24.055654] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 24.056102] PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO [ 24.056133] PCI quirk: region 0480-04bf claimed by ICH6 GPIO [ 24.056753] PCI: Transparent bridge - 0000:00:1e.0 [ 24.056804] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 24.056888] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] [ 24.056939] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT] [ 24.057007] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT] [ 24.057058] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT] [ 24.057102] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT] [ 24.058583] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15) [ 24.058950] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 *7 10 11 12 14 15) [ 24.059315] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 11 12 14 15) [ 24.059679] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 12 14 15) [ 24.060044] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 12 14 15) [ 24.060409] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 *11 12 14 15) [ 24.060774] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 24.061187] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *10 11 12 14 15) [ 24.061558] ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - AD, should be A4 [20070126] [ 24.061641] Linux Plug and Play Support v0.97 (c) Adam Belay [ 24.061686] pnp: PnP ACPI init [ 24.061717] ACPI: bus type pnp registered [ 24.063559] pnp: PnP ACPI: found 15 devices [ 24.063587] ACPI: ACPI bus type pnp unregistered [ 24.063616] PnPBIOS: Disabled by ACPI PNP [ 24.063781] PCI: Using ACPI for IRQ routing [ 24.063809] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 24.089109] NET: Registered protocol family 8 [ 24.089137] NET: Registered protocol family 20 [ 24.089184] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 [ 24.089302] hpet0: 3 64-bit timers, 14318180 Hz [ 24.090348] AppArmor: AppArmor Filesystem Enabled [ 24.093099] Time: tsc clocksource has been installed. [ 24.109100] system 00:01: iomem range 0xfed13000-0xfed19fff has been reserved [ 24.109133] system 00:07: ioport range 0x290-0x297 has been reserved [ 24.109164] system 00:08: ioport range 0x4d0-0x4d1 has been reserved [ 24.109193] system 00:08: ioport range 0x800-0x87f has been reserved [ 24.109207] Switched to high resolution mode on CPU 1 [ 24.109228] system 00:08: ioport range 0x400-0x41f has been reserved [ 24.109257] system 00:08: ioport range 0x480-0x4bf has been reserved [ 24.109286] system 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved [ 24.109316] system 00:08: iomem range 0xfed20000-0xfed3ffff has been reserved [ 24.109346] system 00:08: iomem range 0xfed50000-0xfed8ffff has been reserved [ 24.109375] system 00:08: iomem range 0xffb00000-0xffbfffff could not be reserved [ 24.109409] system 00:08: iomem range 0xfff00000-0xffffffff could not be reserved [ 24.109444] system 00:0b: iomem range 0xfec00000-0xfec00fff has been reserved [ 24.109474] system 00:0b: iomem range 0xfee00000-0xfee00fff has been reserved [ 24.109505] system 00:0d: iomem range 0xf0000000-0xf3ffffff has been reserved [ 24.109537] system 00:0e: iomem range 0x0-0x9ffff could not be reserved [ 24.109567] system 00:0e: iomem range 0xc0000-0xdffff could not be reserved [ 24.109597] system 00:0e: iomem range 0xe0000-0xfffff could not be reserved [ 24.109626] system 00:0e: iomem range 0x100000-0x7fffffff could not be reserved [ 24.109659] system 00:0e: iomem range 0x0-0x0 could not be reserved [ 24.113075] Switched to high resolution mode on CPU 0 [ 24.139892] PCI: Bridge: 0000:00:01.0 [ 24.139921] IO window: c000-cfff [ 24.139949] MEM window: ff900000-ff9fffff [ 24.139978] PREFETCH window: cff00000-efefffff [ 24.140658] PCI: Bridge: 0000:00:1c.0 [ 24.140686] IO window: disabled. [ 24.140715] MEM window: disabled. [ 24.140744] PREFETCH window: cfe00000-cfefffff [ 24.140774] PCI: Bridge: 0000:00:1c.3 [ 24.140802] IO window: b000-bfff [ 24.140832] MEM window: ff800000-ff8fffff [ 24.140861] PREFETCH window: disabled. [ 24.140890] PCI: Bridge: 0000:00:1c.4 [ 24.140919] IO window: a000-afff [ 24.140948] MEM window: ff700000-ff7fffff [ 24.140977] PREFETCH window: disabled. [ 24.141007] PCI: Bridge: 0000:00:1e.0 [ 24.141036] IO window: disabled. [ 24.141065] MEM window: ff600000-ff6fffff [ 24.141094] PREFETCH window: disabled. [ 24.141130] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 24.141187] PCI: Setting latency timer of device 0000:00:01.0 to 64 [ 24.141198] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 24.141255] PCI: Setting latency timer of device 0000:00:1c.0 to 64 [ 24.141267] ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 17 [ 24.141324] PCI: Setting latency timer of device 0000:00:1c.3 to 64 [ 24.141335] ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 16 (level, low) -> IRQ 16 [ 24.141392] PCI: Setting latency timer of device 0000:00:1c.4 to 64 [ 24.141399] PCI: Setting latency timer of device 0000:00:1e.0 to 64 [ 24.141405] NET: Registered protocol family 2 [ 24.184987] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 24.185133] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 24.185444] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 24.185627] TCP: Hash tables configured (established 131072 bind 65536) [ 24.185657] TCP reno registered [ 24.197010] checking if image is initramfs... it is [ 24.573044] Freeing initrd memory: 7692k freed [ 24.573622] audit: initializing netlink socket (disabled) [ 24.573661] audit(1211123751.964:1): initialized [ 24.573847] highmem bounce pool size: 64 pages [ 24.575040] VFS: Disk quotas dquot_6.5.1 [ 24.575116] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 24.575233] io scheduler noop registered [ 24.575262] io scheduler anticipatory registered [ 24.575290] io scheduler deadline registered [ 24.575323] io scheduler cfq registered (default) [ 24.575420] Boot video device is 0000:05:00.0 [ 24.575487] PCI: Setting latency timer of device 0000:00:01.0 to 64 [ 24.575507] assign_interrupt_mode Found MSI capability [ 24.575554] Allocate Port Service[0000:00:01.0:pcie00] [ 24.575600] PCI: Setting latency timer of device 0000:00:1c.0 to 64 [ 24.575628] assign_interrupt_mode Found MSI capability [ 24.575679] Allocate Port Service[0000:00:1c.0:pcie00] [ 24.575698] Allocate Port Service[0000:00:1c.0:pcie02] [ 24.575752] PCI: Setting latency timer of device 0000:00:1c.3 to 64 [ 24.575779] assign_interrupt_mode Found MSI capability [ 24.575830] Allocate Port Service[0000:00:1c.3:pcie00] [ 24.575883] PCI: Setting latency timer of device 0000:00:1c.4 to 64 [ 24.575911] assign_interrupt_mode Found MSI capability [ 24.575961] Allocate Port Service[0000:00:1c.4:pcie00] [ 24.576111] isapnp: Scanning for PnP cards... [ 24.928623] isapnp: No Plug & Play device found [ 24.942880] Real Time Clock Driver v1.12ac [ 24.943047] hpet_resources: 0xfed00000 is busy [ 24.943072] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [ 24.943199] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 24.943632] 00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 24.944308] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize [ 24.944379] input: Macintosh mouse button emulation as /devices/virtual/input/input0 [ 24.944467] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 [ 24.944496] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp [ 24.945008] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 24.971974] mice: PS/2 mouse device common for all mice [ 24.972071] EISA: Probing bus 0 at eisa.0 [ 24.972119] EISA: Detected 0 cards. [ 24.972148] cpuidle: using governor ladder [ 24.972176] cpuidle: using governor menu [ 24.972254] NET: Registered protocol family 1 [ 24.972299] Using IPI No-Shortcut mode [ 24.972346] registered taskstats version 1 [ 24.972439] Magic number: 8:655:285 [ 24.972496] hash matches device PNP0C04:00 [ 24.972527] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 24.972556] EDD information not available. [ 24.972695] Freeing unused kernel memory: 364k freed [ 25.001220] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1 [ 26.102192] fuse init (API version 7.9) [ 26.113006] ACPI Error (psparse-0537): Method parse/execution failed [\_PR_.CPU1._OSC] (Node f7c45198), AE_ALREADY_EXISTS [ 26.113016] ACPI: Marking method _OSC as Serialized [ 26.113041] ACPI Error (psparse-0537): Method parse/execution failed [\_PR_.CPU1._PDC] (Node f7c45180), AE_ALREADY_EXISTS [ 26.113045] ACPI: Marking method _PDC as Serialized [ 26.113080] ACPI: Processor [CPU1] (supports 8 throttling states) [ 26.113170] ACPI Error (psparse-0537): Method parse/execution failed [\_PR_.CPU2._OSC] (Node f7c45270), AE_ALREADY_EXISTS [ 26.113174] ACPI: Marking method _OSC as Serialized [ 26.113193] ACPI Error (psparse-0537): Method parse/execution failed [\_PR_.CPU2._PDC] (Node f7c45258), AE_ALREADY_EXISTS [ 26.113197] ACPI: Marking method _PDC as Serialized [ 26.113242] ACPI: Processor [CPU2] (supports 8 throttling states) [ 26.113250] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126] [ 26.113257] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126] [ 26.306570] usbcore: registered new interface driver usbfs [ 26.306585] usbcore: registered new interface driver hub [ 26.306822] usbcore: registered new device driver usb [ 26.307655] USB Universal Host Controller Interface driver v3.0 [ 26.307697] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) -> IRQ 18 [ 26.307705] PCI: Setting latency timer of device 0000:00:1d.0 to 64 [ 26.307707] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 26.307888] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 [ 26.307909] uhci_hcd 0000:00:1d.0: irq 18, io base 0x0000e480 [ 26.307986] usb usb1: configuration #1 chosen from 1 choice [ 26.308000] hub 1-0:1.0: USB hub found [ 26.308003] hub 1-0:1.0: 2 ports detected [ 26.331398] SCSI subsystem initialized [ 26.341834] libata version 3.00 loaded. [ 26.393483] Floppy drive(s): fd0 is 1.44M [ 26.413651] FDC 0 is a post-1991 82077 [ 26.414097] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 19 [ 26.414104] PCI: Setting latency timer of device 0000:00:1d.1 to 64 [ 26.414107] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 26.414120] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 [ 26.414141] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e800 [ 26.414507] usb usb2: configuration #1 chosen from 1 choice [ 26.414521] hub 2-0:1.0: USB hub found [ 26.414525] hub 2-0:1.0: 2 ports detected [ 26.517940] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 20 [ 26.517949] PCI: Setting latency timer of device 0000:00:1d.2 to 64 [ 26.517952] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 26.517966] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 [ 26.517987] uhci_hcd 0000:00:1d.2: irq 20, io base 0x0000e880 [ 26.518055] usb usb3: configuration #1 chosen from 1 choice [ 26.518070] hub 3-0:1.0: USB hub found [ 26.518073] hub 3-0:1.0: 2 ports detected [ 26.618801] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 17 [ 26.618809] PCI: Setting latency timer of device 0000:00:1d.3 to 64 [ 26.618811] uhci_hcd 0000:00:1d.3: UHCI Host Controller [ 26.618826] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4 [ 26.618847] uhci_hcd 0000:00:1d.3: irq 17, io base 0x0000ec00 [ 26.618910] usb usb4: configuration #1 chosen from 1 choice [ 26.618923] hub 4-0:1.0: USB hub found [ 26.618926] hub 4-0:1.0: 2 ports detected [ 26.649701] usb 1-2: new full speed USB device using uhci_hcd and address 2 [ 26.722739] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 20 (level, low) -> IRQ 18 [ 26.722748] PCI: Setting latency timer of device 0000:00:1d.7 to 64 [ 26.722750] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 26.722766] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5 [ 26.726646] ehci_hcd 0000:00:1d.7: debug port 1 [ 26.726650] PCI: cache line size of 32 is not supported by device 0000:00:1d.7 [ 26.726653] ehci_hcd 0000:00:1d.7: irq 18, io mem 0xffafbc00 [ 26.773538] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 26.773604] usb usb5: configuration #1 chosen from 1 choice [ 26.773617] hub 5-0:1.0: USB hub found [ 26.773621] hub 5-0:1.0: 8 ports detected [ 26.877495] ata_piix 0000:00:1f.1: version 2.12 [ 26.877509] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 22 (level, low) -> IRQ 21 [ 26.877534] PCI: Setting latency timer of device 0000:00:1f.1 to 64 [ 26.877586] scsi0 : ata_piix [ 26.877886] scsi1 : ata_piix [ 26.878580] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14 [ 26.878581] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15 [ 27.169010] usb 1-2: device not accepting address 2, error -71 [ 27.545816] ata1.00: ATAPI: SONY CD-RW CRX175A1, 5YS2, max UDMA/33 [ 27.545832] ata1.01: ATAPI: LITE-ON DVDRW LH-18A1H, HL01, max UDMA/66 [ 27.545841] ata1.01: limited to UDMA/33 due to 40-wire cable [ 27.708530] ata1.00: configured for UDMA/33 [ 27.897279] ata1.01: configured for UDMA/33 [ 28.062770] scsi 0:0:0:0: CD-ROM SONY CD-RW CRX175A1 5YS2 PQ: 0 ANSI: 5 [ 28.063878] scsi 0:0:1:0: CD-ROM LITE-ON DVDRW LH-18A1H HL01 PQ: 0 ANSI: 5 [ 28.063913] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ] [ 28.147708] usb 5-7: new high speed USB device using ehci_hcd and address 4 [ 28.223619] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 23 (level, low) -> IRQ 22 [ 28.223637] PCI: Setting latency timer of device 0000:00:1f.2 to 64 [ 28.223661] scsi2 : ata_piix [ 28.223743] scsi3 : ata_piix [ 28.223760] ata3: SATA max UDMA/133 cmd 0xe400 ctl 0xe080 bmdma 0xd880 irq 22 [ 28.223762] ata4: SATA max UDMA/133 cmd 0xe000 ctl 0xdc00 bmdma 0xd888 irq 22 [ 28.280801] usb 5-7: configuration #1 chosen from 1 choice [ 28.281011] hub 5-7:1.0: USB hub found [ 28.281248] hub 5-7:1.0: 4 ports detected [ 28.388736] ata3.00: ATA-7: Hitachi HDT725032VLA360, V54OA52A, max UDMA/133 [ 28.388739] ata3.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/32) [ 28.403720] ata3.00: configured for UDMA/133 [ 28.623074] usb 1-2: new full speed USB device using uhci_hcd and address 4 [ 28.806647] usb 1-2: configuration #1 chosen from 1 choice [ 29.050508] usb 3-1: new low speed USB device using uhci_hcd and address 2 [ 29.062789] ata4.00: ATA-6: Config Disk, RGL10364, max UDMA/133 [ 29.062791] ata4.00: 640 sectors, multi 1: LBA [ 29.062796] ata4.00: Drive reports diagnostics failure. This may indicate a drive [ 29.062798] ata4.00: fault or invalid emulation. Contact drive vendor for information. [ 29.062801] ata4.00: device is on DMA blacklist, disabling DMA [ 29.063134] ata4.00: configured for PIO4 [ 29.063217] scsi 2:0:0:0: Direct-Access ATA Hitachi HDT72503 V54O PQ: 0 ANSI: 5 [ 29.063301] scsi 3:0:0:0: Direct-Access ATA Config Disk RGL1 PQ: 0 ANSI: 5 [ 29.063588] ACPI: PCI Interrupt 0000:01:03.0[A] -> GSI 21 (level, low) -> IRQ 23 [ 29.113242] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[23] MMIO=[ff6ff800-ff6fffff] Max Packet=[2048] IR/IT contexts=[4/8] [ 29.122563] Driver 'sd' needs updating - please use bus_type methods [ 29.122621] sd 2:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB) [ 29.122628] sd 2:0:0:0: [sda] Write Protect is off [ 29.122629] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 29.122638] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 29.122668] sd 2:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB) [ 29.122674] sd 2:0:0:0: [sda] Write Protect is off [ 29.122675] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 29.122684] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 29.122685] sda:<4>Driver 'sr' needs updating - please use bus_type methods [ 29.126493] sr0: scsi3-mmc drive: 149x/40x writer cd/rw xa/form2 cdda tray [ 29.126495] Uniform CD-ROM driver Revision: 3.20 [ 29.126519] sr 0:0:0:0: Attached scsi CD-ROM sr0 [ 29.133806] sr1: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray [ 29.133830] sr 0:0:1:0: Attached scsi CD-ROM sr1 [ 29.134255] sda1 sda2 < sda5 sda6 > sda3 [ 29.157311] sd 2:0:0:0: [sda] Attached SCSI disk [ 29.159522] sd 3:0:0:0: [sdb] 640 512-byte hardware sectors (0 MB) [ 29.159529] sd 3:0:0:0: [sdb] Write Protect is off [ 29.159530] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 29.159540] sd 3:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 29.159562] sd 3:0:0:0: [sdb] 640 512-byte hardware sectors (0 MB) [ 29.159568] sd 3:0:0:0: [sdb] Write Protect is off [ 29.159569] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 29.159578] sd 3:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 29.159579] sdb:<5>sr 0:0:0:0: Attached scsi generic sg0 type 5 [ 29.160296] sr 0:0:1:0: Attached scsi generic sg1 type 5 [ 29.160306] sd 2:0:0:0: Attached scsi generic sg2 type 0 [ 29.160316] sd 3:0:0:0: Attached scsi generic sg3 type 0 [ 29.222456] usb 3-1: configuration #1 chosen from 1 choice [ 29.422228] usb 5-7.3: new high speed USB device using ehci_hcd and address 5 [ 29.520405] usb 5-7.3: configuration #1 chosen from 1 choice [ 29.521980] usbcore: registered new interface driver hiddev [ 29.527762] input: Logitech USB Gaming Mouse as /devices/pci0000:00/0000:00:1d.0/usb1/1-2/1-2:1.0/input/input2 [ 29.546879] input,hidraw0: USB HID v1.11 Mouse [Logitech USB Gaming Mouse] on usb-0000:00:1d.0-2 [ 29.554620] hiddev96hidraw1: USB HID v1.11 Device [Logitech USB Gaming Mouse] on usb-0000:00:1d.0-2 [ 29.564002] hiddev97hidraw2: USB HID v1.10 Device [T-wins ASUS DH Remote] on usb-0000:00:1d.2-1 [ 29.564010] usbcore: registered new interface driver usbhid [ 29.564011] /build/buildd/linux-2.6.24/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver [ 30.384803] ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011d80000fbed6e] [ 59.119508] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen [ 59.119514] ata4.00: cmd c4/00:08:00:00:00/00:00:00:00:00/e0 tag 0 pio 4096 in [ 59.119515] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 59.119516] ata4.00: status: { DRDY } [ 59.119524] ata4: soft resetting link [ 59.460830] ata4.00: failed to IDENTIFY (INIT_DEV_PARAMS failed, err_mask=0x80) [ 59.460832] ata4.00: revalidation failed (errno=-5) [ 59.460834] ata4: failed to recover some devices, retrying in 5 secs [ 64.455399] ata4: soft resetting link [ 64.797222] ata4.00: failed to IDENTIFY (INIT_DEV_PARAMS failed, err_mask=0x80) [ 64.797224] ata4.00: revalidation failed (errno=-5) [ 64.797226] ata4: failed to recover some devices, retrying in 5 secs [ 69.792298] ata4: soft resetting link [ 74.982387] ata4: port is slow to respond, please be patient (Status 0xd0) [ 79.791988] ata4: SRST failed (errno=-16) [ 79.791991] ata4: soft resetting link [ 84.981083] ata4: port is slow to respond, please be patient (Status 0xd0) [ 89.790686] ata4: SRST failed (errno=-16) [ 89.790689] ata4: soft resetting link [ 94.978780] ata4: port is slow to respond, please be patient (Status 0xd0) [ 124.791112] ata4: SRST failed (errno=-16) [ 124.791117] ata4: soft resetting link [ 129.812430] ata4: SRST failed (errno=-16) [ 129.812434] ata4: reset failed, giving up [ 129.812436] ata4.00: disabled [ 134.846730] ata4: port is slow to respond, please be patient (Status 0xd0) [ 139.823110] ata4: device not ready (errno=-16), forcing hardreset [ 139.823113] ata4: soft resetting link [ 145.012206] ata4: port is slow to respond, please be patient (Status 0xd0) [ 149.821814] ata4: SRST failed (errno=-16) [ 149.821817] ata4: soft resetting link [ 155.010899] ata4: port is slow to respond, please be patient (Status 0xd0) [ 159.821499] ata4: SRST failed (errno=-16) [ 159.821502] ata4: soft resetting link [ 165.009595] ata4: port is slow to respond, please be patient (Status 0xd0) [ 194.818935] ata4: SRST failed (errno=-16) [ 194.818940] ata4: soft resetting link [ 199.839252] ata4: SRST failed (errno=-16) [ 199.839257] ata4: reset failed, giving up [ 199.839269] ata4: EH complete [ 199.839283] sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK [ 199.839287] end_request: I/O error, dev sdb, sector 0 [ 199.839289] Buffer I/O error on device sdb, logical block 0 [ 199.839315] sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK [ 199.839318] end_request: I/O error, dev sdb, sector 0 [ 199.839320] Buffer I/O error on device sdb, logical block 0 [ 199.839335] sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK [ 199.839337] end_request: I/O error, dev sdb, sector 0 [ 199.839339] Buffer I/O error on device sdb, logical block 0 [ 199.839350] sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK [ 199.839352] end_request: I/O error, dev sdb, sector 0 [ 199.839353] Buffer I/O error on device sdb, logical block 0 [ 199.839364] sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK [ 199.839366] end_request: I/O error, dev sdb, sector 0 [ 199.839368] Buffer I/O error on device sdb, logical block 0 [ 199.839372] ldm_validate_partition_table(): Disk read failed. [ 199.839379] sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK [ 199.839381] end_request: I/O error, dev sdb, sector 0 [ 199.839382] Buffer I/O error on device sdb, logical block 0 [ 199.839393] sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK [ 199.839395] end_request: I/O error, dev sdb, sector 0 [ 199.839396] Buffer I/O error on device sdb, logical block 0 [ 199.839406] sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK [ 199.839408] end_request: I/O error, dev sdb, sector 0 [ 199.839409] Buffer I/O error on device sdb, logical block 0 [ 199.839419] sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK [ 199.839421] end_request: I/O error, dev sdb, sector 0 [ 199.839422] Buffer I/O error on device sdb, logical block 0 [ 199.839426] Dev sdb: unable to read RDB block 0 [ 199.839434] sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK [ 199.839435] end_request: I/O error, dev sdb, sector 0 [ 199.839437] Buffer I/O error on device sdb, logical block 0 [ 199.839447] sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK [ 199.839449] end_request: I/O error, dev sdb, sector 0 [ 199.839461] sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK [ 199.839463] end_request: I/O error, dev sdb, sector 24 [ 199.839471] sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK [ 199.839473] end_request: I/O error, dev sdb, sector 24 [ 199.839482] sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK [ 199.839484] end_request: I/O error, dev sdb, sector 0 [ 199.839494] sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK [ 199.839496] end_request: I/O error, dev sdb, sector 0 [ 199.839499] unable to read partition table [ 199.839539] sd 3:0:0:0: [sdb] Attached SCSI disk [ 199.856805] sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK [ 199.856810] end_request: I/O error, dev sdb, sector 0 [ 199.856819] sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK [ 199.856821] end_request: I/O error, dev sdb, sector 0 [ 200.020694] Attempting manual resume [ 200.020696] swsusp: Resume From Partition 8:5 [ 200.020697] PM: Checking swsusp image. [ 200.020795] PM: Resume from disk failed. [ 200.051929] kjournald starting. Commit interval 5 seconds [ 200.051933] EXT3-fs: mounted filesystem with ordered data mode. [ 204.410473] sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK [ 204.410480] end_request: I/O error, dev sdb, sector 0 [ 204.410490] sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK [ 204.410492] end_request: I/O error, dev sdb, sector 0 [ 204.713821] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 204.737797] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 204.773727] iTCO_vendor_support: vendor-support=0 [ 204.798519] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007) [ 204.798575] iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0860) [ 204.798600] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) [ 204.877601] EDAC MC: Ver: 2.1.0 Apr 10 2008 [ 204.937970] intel_rng: FWH not detected [ 205.009476] input: PC Speaker as /devices/platform/pcspkr/input/input3 [ 205.035532] input: Power Button (FF) as /devices/virtual/input/input4 [ 205.036757] EDAC i82975x: ECC disabled on both channels. [ 205.073296] ACPI: Power Button (FF) [PWRF] [ 205.073362] input: Power Button (CM) as /devices/virtual/input/input5 [ 205.105252] ACPI: Power Button (CM) [PWRB] [ 205.318187] Linux agpgart interface v0.102 [ 205.415903] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 19 (level, low) -> IRQ 17 [ 205.415915] PCI: Setting latency timer of device 0000:03:00.0 to 64 [ 205.415934] sky2 0000:03:00.0: v1.20 addr 0xff8fc000 irq 17 Yukon-EC (0xb6) rev 2 [ 205.416200] sky2 eth0: addr 00:18:f3:cd:8a:b6 [ 205.416214] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 205.416219] PCI: Setting latency timer of device 0000:02:00.0 to 64 [ 205.416235] sky2 0000:02:00.0: v1.20 addr 0xff7fc000 irq 16 Yukon-EC (0xb6) rev 2 [ 205.416474] sky2 eth1: addr 00:18:f3:cd:78:a0 [ 205.515018] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 19 (level, low) -> IRQ 17 [ 205.515040] PCI: Setting latency timer of device 0000:00:1b.0 to 64 [ 205.981130] phy0: Selected rate control algorithm 'simple' [ 206.026514] phy0: hwaddr 00:15:af:0b:b9:53, rtl8187 V1 + rtl8225z2 [ 206.026527] usbcore: registered new interface driver rtl8187 [ 206.132342] sky2 eth0: enabling interface [ 206.660506] loop: module loaded [ 206.685999] lp: driver loaded but no devices found [ 206.766697] w83627ehf: Found W83627DHG chip at 0x290 [ 206.806204] Adding 2104472k swap on /dev/sda5. Priority:-1 extents:1 across:2104472k [ 207.380640] EXT3 FS on sda3, internal journal [ 207.460176] RPC: Registered udp transport module. [ 207.460178] RPC: Registered tcp transport module. [ 207.519290] device-mapper: uevent: version 1.0.3 [ 207.519308] device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@redhat.com [ 207.797839] sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both [ 208.313588] kjournald starting. Commit interval 5 seconds [ 208.320309] EXT3 FS on sda6, internal journal [ 208.320312] EXT3-fs: mounted filesystem with ordered data mode. [ 208.646460] ip_tables: (C) 2000-2006 Netfilter Core Team [ 209.005933] NET: Registered protocol family 10 [ 209.006095] lo: Disabled Privacy Extensions [ 209.298951] No dock devices found. [ 210.321881] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) [ 210.321884] apm: disabled - APM is not SMP safe. [ 210.516418] ppdev: user-space parallel port driver [ 210.613217] audit(1211116739.023:2): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/dev/tty" pid=22052 profile="/usr/sbin/cupsd" namespace="default" [ 212.776603] vboxdrv: Trying to deactivate the NMI watchdog permanently... [ 212.776607] vboxdrv: Successfully done. [ 212.776644] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'. [ 212.776646] vboxdrv: Successfully loaded version 1.5.6_OSE (interface 0x00050002). [ 214.317524] sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK [ 214.317532] end_request: I/O error, dev sdb, sector 0 [ 214.317534] printk: 15 messages suppressed. [ 214.317536] Buffer I/O error on device sdb, logical block 0 [ 214.317541] Buffer I/O error on device sdb, logical block 1 [ 214.317555] sd 3:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK [ 214.317559] end_request: I/O error, dev sdb, sector 0 [ 214.445630] Bluetooth: Core ver 2.11 [ 214.445972] NET: Registered protocol family 31 [ 214.445975] Bluetooth: HCI device and connection manager initialized [ 214.445977] Bluetooth: HCI socket layer initialized [ 214.467378] Bluetooth: L2CAP ver 2.9 [ 214.467381] Bluetooth: L2CAP socket layer initialized [ 214.506213] Bluetooth: RFCOMM socket layer initialized [ 214.506510] Bluetooth: RFCOMM TTY layer initialized [ 214.506513] Bluetooth: RFCOMM ver 1.8 [ 216.074984] [drm] Initialized drm 1.1.0 20060810 [ 219.752754] eth0: no IPv6 routers present [ 222.968778] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 222.986859] sky2 eth1: enabling interface [ 222.990455] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 224.606325] NET: Registered protocol family 17