camera does not mount anymore

[ezechiel]

I use a coolpix 2000 camera since some years now. I used it with feisty and used it with gutsy. The any update in the last weeks disabled the ability to mount the camera any more.
It is recognized, but before really mounting it it outputs: reset full speed USB device using uhci_hcd and address xy

My dmesg is

[17897.772000] usb-storage: device found at 2
[17897.772000] usb-storage: waiting for device to settle before scanning
[17902.772000] usb-storage: device scan complete
[17902.776000] scsi 3:0:0:0: Direct-Access NIKON DSC E2000 1.00 PQ: 0 ANSI: 2
[17902.784000] sd 3:0:0:0: [sdc] 4001761 512-byte hardware sectors (2049 MB)
[17902.788000] sd 3:0:0:0: [sdc] Write Protect is off
[17902.788000] sd 3:0:0:0: [sdc] Mode Sense: 04 00 00 00
[17902.788000] sd 3:0:0:0: [sdc] Assuming drive cache: write through
[17902.796000] sd 3:0:0:0: [sdc] 4001761 512-byte hardware sectors (2049 MB)
[17902.800000] sd 3:0:0:0: [sdc] Write Protect is off
[17902.800000] sd 3:0:0:0: [sdc] Mode Sense: 04 00 00 00
[17902.800000] sd 3:0:0:0: [sdc] Assuming drive cache: write through
[17902.800000] sdc: sdc1
[17902.812000] sd 3:0:0:0: [sdc] Attached SCSI removable disk
[17902.812000] sd 3:0:0:0: Attached scsi generic sg3 type 0
[17903.176000] usb 3-1: reset full speed USB device using uhci_hcd and address 2
[17903.452000] usb 3-1: reset full speed USB device using uhci_hcd and address 2
[17903.728000] usb 3-1: reset full speed USB device using uhci_hcd and address 2
[17904.004000] usb 3-1: reset full speed USB device using uhci_hcd and address 2
[17904.276000] usb 3-1: reset full speed USB device using uhci_hcd and address 2

Then I turn the camera off again.

[17924.016000] usb 3-1: USB disconnect, address 2
[17924.016000] sd 3:0:0:0: [sdc] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[17924.016000] end_request: I/O error, dev sdc, sector 4001760
[17924.016000] Buffer I/O error on device sdc, logical block 4001760
[17924.020000] sd 3:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_OK
[17924.020000] end_request: I/O error, dev sdc, sector 4001760
[17924.020000] Buffer I/O error on device sdc, logical block 4001760
[17924.020000] Buffer I/O error on device sdc, logical block 4001752
[17924.020000] Buffer I/O error on device sdc, logical block 4001753
[17924.020000] Buffer I/O error on device sdc, logical block 4001754
[17924.020000] Buffer I/O error on device sdc, logical block 4001755
[17924.020000] Buffer I/O error on device sdc, logical block 4001756
[17924.020000] Buffer I/O error on device sdc, logical block 4001757
[17924.020000] Buffer I/O error on device sdc, logical block 4001758
[17924.020000] Buffer I/O error on device sdc, logical block 4001759

I assume that it is a kernel bug, because some time in February the 2.6.22 was rolled out - and that might have been the time when my camera stopped working.

Obviously it is not https://bugs.launchpad.net/ubuntu/+source/linux-source-2.6.22/+bug/134477, as already discussed there.

Is there any solution to this despite updating to hardy?

regards ezechiel

[ezechiel (private-alexanderbraun)]

as panchenko states on https://bugs.launchpad.net/bugs/134477 this bug still exists and therefore it seems to be a duplicate on 134477

[ezechiel (private-alexanderbraun)]

Closed regarding procedure of https://bugs.launchpad.net/ubuntu/+source/linux/+bug/134477
Will create new and specialized report