root@holo:~# smartctl -a /dev/sdc smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.15.0-43-generic] (local build) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Red Device Model: WDC WD20EFRX-68EUZN0 Serial Number: WD-WCC4M0TZJ6PZ LU WWN Device Id: 5 0014ee 2b8467101 Firmware Version: 82.00A82 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sat Jan 12 16:12:41 2019 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (26280) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 266) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x703d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0027 175 175 021 Pre-fail Always - 4216 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 46 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 2124 10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 46 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 23 193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 89 194 Temperature_Celsius 0x0022 118 110 000 Old_age Always - 29 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Conveyance offline Completed without error 00% 2081 - # 2 Short offline Completed without error 00% 2080 - # 3 Short offline Completed without error 00% 2071 - # 4 Short offline Completed without error 00% 2069 - # 5 Conveyance offline Completed without error 00% 2069 - # 6 Conveyance offline Completed without error 00% 2069 - # 7 Short offline Completed without error 00% 2068 - # 8 Short offline Completed without error 00% 2068 - # 9 Conveyance offline Completed without error 00% 2068 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. root@holo:~# echo $? 0 root@holo:~# smartctl --xall /dev/sdc smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.15.0-43-generic] (local build) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Red Device Model: WDC WD20EFRX-68EUZN0 Serial Number: WD-WCC4M0TZJ6PZ LU WWN Device Id: 5 0014ee 2b8467101 Firmware Version: 82.00A82 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sat Jan 12 16:12:51 2019 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Disabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (26280) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 266) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x703d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 175 175 021 - 4216 4 Start_Stop_Count -O--CK 100 100 000 - 46 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 098 098 000 - 2124 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 46 192 Power-Off_Retract_Count -O--CK 200 200 000 - 23 193 Load_Cycle_Count -O--CK 200 200 000 - 89 194 Temperature_Celsius -O---K 118 110 000 - 29 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x0c GPL R/O 2048 Pending Defects log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 122 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 122 [1] occurred at disk power-on lifetime: 2055 hours (85 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 05 c4 69 f0 a0 00 Error: IDNF at LBA = 0x05c469f0 = 96758256 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 01 28 00 b0 00 00 05 c4 69 f0 40 08 00:03:49.606 WRITE FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:03:49.606 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:03:49.606 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:03:49.605 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:03:49.605 SET FEATURES [Set transfer mode] Error 121 [0] occurred at disk power-on lifetime: 2055 hours (85 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 05 c4 69 f0 a0 00 Error: IDNF at LBA = 0x05c469f0 = 96758256 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 01 28 00 28 00 00 05 c4 69 f0 40 08 00:03:42.577 WRITE FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:03:42.577 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:03:42.577 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:03:42.576 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:03:42.576 SET FEATURES [Set transfer mode] Error 120 [23] occurred at disk power-on lifetime: 2055 hours (85 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 05 c4 69 f0 a0 00 Error: IDNF at LBA = 0x05c469f0 = 96758256 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 01 28 00 98 00 00 05 c4 69 f0 40 08 00:03:35.556 WRITE FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:03:35.556 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:03:35.556 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:03:35.556 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:03:35.556 SET FEATURES [Set transfer mode] Error 119 [22] occurred at disk power-on lifetime: 2055 hours (85 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 05 c4 69 f0 a0 00 Error: IDNF at LBA = 0x05c469f0 = 96758256 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 01 28 00 10 00 00 05 c4 69 f0 40 08 00:03:28.536 WRITE FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:03:28.536 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:03:28.536 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:03:28.536 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:03:28.536 SET FEATURES [Set transfer mode] Error 118 [21] occurred at disk power-on lifetime: 2055 hours (85 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 05 c4 69 f0 a0 00 Error: IDNF at LBA = 0x05c469f0 = 96758256 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 01 28 00 78 00 00 05 c4 69 f0 40 08 00:03:21.519 WRITE FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:03:21.519 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:03:21.519 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:03:21.518 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:03:21.518 SET FEATURES [Set transfer mode] Error 117 [20] occurred at disk power-on lifetime: 2055 hours (85 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 05 c4 69 f0 40 00 Error: IDNF at LBA = 0x05c469f0 = 96758256 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 01 28 00 68 00 00 05 c4 69 f0 40 08 00:03:14.377 WRITE FPDMA QUEUED 60 01 00 00 60 00 00 00 b0 1a 00 40 08 00:03:13.826 READ FPDMA QUEUED 60 01 00 00 58 00 00 00 b0 19 00 40 08 00:03:13.825 READ FPDMA QUEUED 60 01 00 00 50 00 00 00 b0 18 00 40 08 00:03:13.824 READ FPDMA QUEUED 60 01 00 00 48 00 00 00 b0 17 00 40 08 00:03:13.823 READ FPDMA QUEUED Error 116 [19] occurred at disk power-on lifetime: 2055 hours (85 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 05 c4 49 f8 a0 00 Error: IDNF at LBA = 0x05c449f8 = 96750072 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 01 f8 00 a8 00 00 05 c4 49 f8 40 08 00:02:59.804 WRITE FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:02:59.804 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:02:59.804 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:02:59.804 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:02:59.804 SET FEATURES [Set transfer mode] Error 115 [18] occurred at disk power-on lifetime: 2055 hours (85 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 05 c4 49 f8 a0 00 Error: IDNF at LBA = 0x05c449f8 = 96750072 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 01 f8 00 18 00 00 05 c4 49 f8 40 08 00:02:52.791 WRITE FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:02:52.791 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:02:52.791 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:02:52.791 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:02:52.791 SET FEATURES [Set transfer mode] SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Conveyance offline Completed without error 00% 2081 - # 2 Short offline Completed without error 00% 2080 - # 3 Short offline Completed without error 00% 2071 - # 4 Short offline Completed without error 00% 2069 - # 5 Conveyance offline Completed without error 00% 2069 - # 6 Conveyance offline Completed without error 00% 2069 - # 7 Short offline Completed without error 00% 2068 - # 8 Short offline Completed without error 00% 2068 - # 9 Conveyance offline Completed without error 00% 2068 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 29 Celsius Power Cycle Min/Max Temperature: 20/30 Celsius Lifetime Min/Max Temperature: 20/37 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (257) Index Estimated Time Temperature Celsius 258 2019-01-12 08:15 29 ********** ... ..(476 skipped). .. ********** 257 2019-01-12 16:12 29 ********** SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 46 --- Lifetime Power-On Resets 0x01 0x010 4 2124 --- Power-on Hours 0x01 0x018 6 9690879181 --- Logical Sectors Written 0x01 0x020 6 80026445 --- Number of Write Commands 0x01 0x028 6 35989345559 --- Logical Sectors Read 0x01 0x030 6 154605564 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 1992 --- Spindle Motor Power-on Hours 0x03 0x010 4 1967 --- Head Flying Hours 0x03 0x018 4 113 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 122 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 1245203 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 28 --- Current Temperature 0x05 0x010 1 27 --- Average Short Term Temperature 0x05 0x018 1 29 --- Average Long Term Temperature 0x05 0x020 1 36 --- Highest Temperature 0x05 0x028 1 23 --- Lowest Temperature 0x05 0x030 1 33 --- Highest Average Short Term Temperature 0x05 0x038 1 26 --- Lowest Average Short Term Temperature 0x05 0x040 1 30 --- Highest Average Long Term Temperature 0x05 0x048 1 29 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 241 --- Number of Hardware Resets 0x06 0x010 4 10166 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 5 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 160933 Vendor specific root@holo:~# echo $? 64