************ lspci -vvnn

00:00.0 Host bridge [0600]: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller [8086:29c0] (rev 10)
	Subsystem: ASRock Incorporation Device [1849:29c0]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: <access denied>
	Kernel driver in use: agpgart-intel
	Kernel modules: intel-agp

00:02.0 VGA compatible controller [0300]: Intel Corporation 82G33/G31 Express Integrated Graphics Controller [8086:29c2] (rev 10)
	Subsystem: ASRock Incorporation Device [1849:29c2]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at fe980000 (32-bit, non-prefetchable) [size=512K]
	Region 1: I/O ports at dc00 [size=8]
	Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M]
	Region 3: Memory at fe800000 (32-bit, non-prefetchable) [size=1M]
	Capabilities: <access denied>

00:1b.0 Audio device [0403]: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller [8086:27d8] (rev 01)
	Subsystem: ASRock Incorporation Device [1849:3662]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at fe978000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: <access denied>
	Kernel driver in use: HDA Intel
	Kernel modules: snd-hda-intel

00:1c.0 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 [8086:27d0] (rev 01)
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
	Prefetchable memory behind bridge: 00000000fdf00000-00000000fdffffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport-driver
	Kernel modules: shpchp

00:1c.1 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 [8086:27d2] (rev 01)
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	I/O behind bridge: 0000e000-0000efff
	Memory behind bridge: fea00000-feafffff
	Prefetchable memory behind bridge: 00000000fde00000-00000000fdefffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport-driver
	Kernel modules: shpchp

00:1d.0 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 [8086:27c8] (rev 01)
	Subsystem: ASRock Incorporation Device [1849:27c8]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 23
	Region 4: I/O ports at d400 [size=32]
	Kernel driver in use: uhci_hcd
	Kernel modules: uhci-hcd

00:1d.1 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 [8086:27c9] (rev 01)
	Subsystem: ASRock Incorporation Device [1849:27c9]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 19
	Region 4: I/O ports at d480 [size=32]
	Kernel driver in use: uhci_hcd
	Kernel modules: uhci-hcd

00:1d.2 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 [8086:27ca] (rev 01)
	Subsystem: ASRock Incorporation Device [1849:27ca]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin C routed to IRQ 18
	Region 4: I/O ports at d800 [size=32]
	Kernel driver in use: uhci_hcd
	Kernel modules: uhci-hcd

00:1d.3 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 [8086:27cb] (rev 01)
	Subsystem: ASRock Incorporation Device [1849:27cb]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin D routed to IRQ 16
	Region 4: I/O ports at d880 [size=32]
	Kernel driver in use: uhci_hcd
	Kernel modules: uhci-hcd

00:1d.7 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller [8086:27cc] (rev 01) (prog-if 20)
	Subsystem: ASRock Incorporation Device [1849:27cc]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 23
	Region 0: Memory at fe977c00 (32-bit, non-prefetchable) [size=1K]
	Capabilities: <access denied>
	Kernel driver in use: ehci_hcd
	Kernel modules: ehci-hcd

00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev e1) (prog-if 01)
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
	Memory behind bridge: feb00000-febfffff
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>

00:1f.0 ISA bridge [0601]: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge [8086:27b8] (rev 01)
	Subsystem: ASRock Incorporation Device [1849:27b8]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: <access denied>
	Kernel modules: intel-rng, iTCO_wdt

00:1f.1 IDE interface [0101]: Intel Corporation 82801G (ICH7 Family) IDE Controller [8086:27df] (rev 01) (prog-if 8a [Master SecP PriP])
	Subsystem: ASRock Incorporation Device [1849:27df]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
	Latency: 0
	Interrupt: pin A routed to IRQ 18
	Region 0: I/O ports at 01f0 [size=8]
	Region 1: I/O ports at 03f4 [size=1]
	Region 2: I/O ports at 0170 [size=8]
	Region 3: I/O ports at 0374 [size=1]
	Region 4: I/O ports at ffa0 [size=16]
	Kernel driver in use: ata_piix
	Kernel modules: ata_piix

00:1f.2 IDE interface [0101]: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller [8086:27c0] (rev 01) (prog-if 8f [Master SecP SecO PriP PriO])
	Subsystem: ASRock Incorporation Device [1849:27c0]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 19
	Region 0: I/O ports at d080 [size=8]
	Region 1: I/O ports at d000 [size=4]
	Region 2: I/O ports at cc00 [size=8]
	Region 3: I/O ports at c880 [size=4]
	Region 4: I/O ports at c800 [size=16]
	Capabilities: <access denied>
	Kernel driver in use: ata_piix
	Kernel modules: ata_piix

00:1f.3 SMBus [0c05]: Intel Corporation 82801G (ICH7 Family) SMBus Controller [8086:27da] (rev 01)
	Subsystem: ASRock Incorporation Device [1849:27da]
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin B routed to IRQ 5
	Region 4: I/O ports at 0400 [size=32]
	Kernel modules: i2c-i801

01:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 02)
	Subsystem: ASRock Incorporation Device [1849:8136]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 221
	Region 0: I/O ports at e800 [size=256]
	Region 2: Memory at fdeff000 (64-bit, prefetchable) [size=4K]
	Region 4: Memory at fdee0000 (64-bit, prefetchable) [size=64K]
	Expansion ROM at feae0000 [disabled] [size=128K]
	Capabilities: <access denied>
	Kernel driver in use: r8169
	Kernel modules: r8169

03:01.0 USB Controller [0c03]: ALi Corporation USB 1.1 Controller [10b9:5237] (rev 03) (prog-if 10)
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32 (20000ns max), Cache Line Size: 32 bytes
	Interrupt: pin B routed to IRQ 23
	Region 0: Memory at febfe000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: <access denied>
	Kernel driver in use: ohci_hcd
	Kernel modules: ohci-hcd

03:01.3 USB Controller [0c03]: ALi Corporation USB 2.0 Controller [10b9:5239] (rev 01) (prog-if 20)
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32 (20000ns max), Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 22
	Region 0: Memory at febffc00 (32-bit, non-prefetchable) [size=256]
	Capabilities: <access denied>
	Kernel driver in use: ehci_hcd
	Kernel modules: ehci-hcd


Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0001 1.1 root hub
  bcdDevice            2.06
  iManufacturer           3 Linux 2.6.27-9-generic ohci_hcd
  iProduct                2 OHCI Host Controller
  iSerial                 1 0000:03:01.0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0 
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0 
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0002  1x 2 bytes
        bInterval             255
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             2
  wHubCharacteristic 0x0002
    No power switching (usb 1.0)
    Ganged overcurrent protection
  bPwrOn2PwrGood        1 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
   Port 2: 0000.0100 power
Device Status:     0x0003
  Self Powered
  Remote Wakeup Enabled

Bus 005 Device 006: ID 0951:1603 Kingston Technology Data Traveler 1GB/2GB Pen Drive
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0 
  bDeviceProtocol         0 
  bMaxPacketSize0        64
  idVendor           0x0951 Kingston Technology
  idProduct          0x1603 Data Traveler 1GB/2GB Pen Drive
  bcdDevice            2.00
  iManufacturer           1 Kingston
  iProduct                2 DataTraveler 2.0
  iSerial                 3 001000000000000000000045
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           32
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0 
    bmAttributes         0x80
      (Bus Powered)
    MaxPower              100mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass         8 Mass Storage
      bInterfaceSubClass      6 SCSI
      bInterfaceProtocol     80 Bulk (Zip)
      iInterface              0 
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x02  EP 2 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
Device Qualifier (for other device speed):
  bLength                10
  bDescriptorType         6
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0 
  bDeviceProtocol         0 
  bMaxPacketSize0        64
  bNumConfigurations      1
Device Status:     0x0000
  (Bus Powered)

Bus 005 Device 004: ID 1058:0300 Western Digital Technologies, Inc. 
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0 
  bDeviceProtocol         0 
  bMaxPacketSize0        64
  idVendor           0x1058 Western Digital Technologies, Inc.
  idProduct          0x0300 
  bcdDevice           ff.ff
  iManufacturer           1 Western Digital Corporation
  iProduct                2 Western Digital USB Hard Drive
  iSerial                 3 AA040131020323
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           32
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0 
    bmAttributes         0xc0
      Self Powered
    MaxPower                2mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass         8 Mass Storage
      bInterfaceSubClass      6 SCSI
      bInterfaceProtocol     80 Bulk (Zip)
      iInterface              0 
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x02  EP 2 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
Device Qualifier (for other device speed):
  bLength                10
  bDescriptorType         6
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0 
  bDeviceProtocol         0 
  bMaxPacketSize0        64
  bNumConfigurations      1
Device Status:     0x0001
  Self Powered

Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0002 2.0 root hub
  bcdDevice            2.06
  iManufacturer           3 Linux 2.6.27-9-generic ehci_hcd
  iProduct                2 EHCI Host Controller
  iSerial                 1 0000:00:1d.7
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0 
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0 
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0004  1x 4 bytes
        bInterval              12
Hub Descriptor:
  bLength              11
  bDescriptorType      41
  nNbrPorts             8
  wHubCharacteristic 0x000a
    No power switching (usb 1.0)
    Per-port overcurrent protection
  bPwrOn2PwrGood       10 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00 0x00
  PortPwrCtrlMask    0xff 0xff
 Hub Port Status:
   Port 1: 0000.0100 power
   Port 2: 0000.0100 power
   Port 3: 0000.0503 highspeed power enable connect
   Port 4: 0000.0100 power
   Port 5: 0000.0100 power
   Port 6: 0000.0503 highspeed power enable connect
   Port 7: 0000.0100 power
   Port 8: 0000.0100 power
Device Status:     0x0003
  Self Powered
  Remote Wakeup Enabled

Bus 006 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0002 2.0 root hub
  bcdDevice            2.06
  iManufacturer           3 Linux 2.6.27-9-generic ehci_hcd
  iProduct                2 EHCI Host Controller
  iSerial                 1 0000:03:01.3
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0 
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0 
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0004  1x 4 bytes
        bInterval              12
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             6
  wHubCharacteristic 0x0009
    Per-port power switching
    Per-port overcurrent protection
  bPwrOn2PwrGood       10 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
   Port 2: 0000.0100 power
   Port 3: 0000.0100 power
   Port 4: 0000.0100 power
   Port 5: 0000.0100 power
   Port 6: 0000.0100 power
Device Status:     0x0003
  Self Powered
  Remote Wakeup Enabled

Bus 004 Device 002: ID 058f:6362 Alcor Micro Corp. Hi-Speed 21-in-1 Flash Card Reader/Writer (Internal/External)
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0 
  bDeviceProtocol         0 
  bMaxPacketSize0        64
  idVendor           0x058f Alcor Micro Corp.
  idProduct          0x6362 Hi-Speed 21-in-1 Flash Card Reader/Writer (Internal/External)
  bcdDevice            1.29
  iManufacturer           1 Generic
  iProduct                2 Mass Storage Device
  iSerial                 3 058F312D81B
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           32
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0 
    bmAttributes         0x80
      (Bus Powered)
    MaxPower              250mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass         8 Mass Storage
      bInterfaceSubClass      6 SCSI
      bInterfaceProtocol     80 Bulk (Zip)
      iInterface              0 
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x01  EP 1 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x82  EP 2 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               0
Device Qualifier (for other device speed):
  bLength                10
  bDescriptorType         6
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0 
  bDeviceProtocol         0 
  bMaxPacketSize0        64
  bNumConfigurations      1
Device Status:     0x0000
  (Bus Powered)

Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0001 1.1 root hub
  bcdDevice            2.06
  iManufacturer           3 Linux 2.6.27-9-generic uhci_hcd
  iProduct                2 UHCI Host Controller
  iSerial                 1 0000:00:1d.3
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0 
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0 
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0002  1x 2 bytes
        bInterval             255
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             2
  wHubCharacteristic 0x000a
    No power switching (usb 1.0)
    Per-port overcurrent protection
  bPwrOn2PwrGood        1 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0103 power enable connect
   Port 2: 0000.0100 power
Device Status:     0x0003
  Self Powered
  Remote Wakeup Enabled

Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0001 1.1 root hub
  bcdDevice            2.06
  iManufacturer           3 Linux 2.6.27-9-generic uhci_hcd
  iProduct                2 UHCI Host Controller
  iSerial                 1 0000:00:1d.2
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0 
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0 
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0002  1x 2 bytes
        bInterval             255
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             2
  wHubCharacteristic 0x000a
    No power switching (usb 1.0)
    Per-port overcurrent protection
  bPwrOn2PwrGood        1 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
   Port 2: 0000.0100 power
Device Status:     0x0003
  Self Powered
  Remote Wakeup Enabled

Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0001 1.1 root hub
  bcdDevice            2.06
  iManufacturer           3 Linux 2.6.27-9-generic uhci_hcd
  iProduct                2 UHCI Host Controller
  iSerial                 1 0000:00:1d.1
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0 
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0 
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0002  1x 2 bytes
        bInterval             255
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             2
  wHubCharacteristic 0x000a
    No power switching (usb 1.0)
    Per-port overcurrent protection
  bPwrOn2PwrGood        1 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
   Port 2: 0000.0100 power
Device Status:     0x0003
  Self Powered
  Remote Wakeup Enabled

Bus 001 Device 005: ID 0a81:0101 Chesen Electronics Corp. Keyboard
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0 
  bDeviceProtocol         0 
  bMaxPacketSize0         8
  idVendor           0x0a81 Chesen Electronics Corp.
  idProduct          0x0101 Keyboard
  bcdDevice            1.10
  iManufacturer           1 CHESEN
  iProduct                2 USB Keyboard
  iSerial                 0 
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           59
    bNumInterfaces          2
    bConfigurationValue     1
    iConfiguration          0 
    bmAttributes         0xa0
      (Bus Powered)
      Remote Wakeup
    MaxPower              100mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         3 Human Interface Device
      bInterfaceSubClass      1 Boot Interface Subclass
      bInterfaceProtocol      1 Keyboard
      iInterface              0 
        HID Device Descriptor:
          bLength                 9
          bDescriptorType        33
          bcdHID               1.10
          bCountryCode           33 US
          bNumDescriptors         1
          bDescriptorType        34 Report
          wDescriptorLength      65
         Report Descriptors: 
           ** UNAVAILABLE **
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0008  1x 8 bytes
        bInterval              10
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        1
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         3 Human Interface Device
      bInterfaceSubClass      0 No Subclass
      bInterfaceProtocol      0 None
      iInterface              0 
        HID Device Descriptor:
          bLength                 9
          bDescriptorType        33
          bcdHID               1.10
          bCountryCode           33 US
          bNumDescriptors         1
          bDescriptorType        34 Report
          wDescriptorLength     102
         Report Descriptors: 
           ** UNAVAILABLE **
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x82  EP 2 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0008  1x 8 bytes
        bInterval              10
Device Status:     0x0000
  (Bus Powered)

Bus 001 Device 006: ID 15d9:0a33  
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0 
  bDeviceProtocol         0 
  bMaxPacketSize0         8
  idVendor           0x15d9 
  idProduct          0x0a33 
  bcdDevice            1.00
  iManufacturer           0 
  iProduct                1 USB Mouse
  iSerial                 0 
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           34
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0 
    bmAttributes         0xa0
      (Bus Powered)
      Remote Wakeup
    MaxPower              100mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         3 Human Interface Device
      bInterfaceSubClass      1 Boot Interface Subclass
      bInterfaceProtocol      2 Mouse
      iInterface              0 
        HID Device Descriptor:
          bLength                 9
          bDescriptorType        33
          bcdHID               1.10
          bCountryCode            0 Not supported
          bNumDescriptors         1
          bDescriptorType        34 Report
          wDescriptorLength      52
         Report Descriptors: 
           ** UNAVAILABLE **
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0004  1x 4 bytes
        bInterval              10
Device Status:     0x0000
  (Bus Powered)

Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0001 1.1 root hub
  bcdDevice            2.06
  iManufacturer           3 Linux 2.6.27-9-generic uhci_hcd
  iProduct                2 UHCI Host Controller
  iSerial                 1 0000:00:1d.0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0 
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0 
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0002  1x 2 bytes
        bInterval             255
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             2
  wHubCharacteristic 0x000a
    No power switching (usb 1.0)
    Per-port overcurrent protection
  bPwrOn2PwrGood        1 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0303 lowspeed power enable connect
   Port 2: 0000.0303 lowspeed power enable connect
Device Status:     0x0003
  Self Powered
  Remote Wakeup Enabled

******************* dmesg.log ********** DOESN'T WORK ****************

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.27-9-generic (buildd@rothera) (gcc version 4.3.2 (Ubuntu 4.3.2-1ubuntu11) ) #1 SMP Thu Nov 20 21:57:00 UTC 2008 (Ubuntu 2.6.27-9.19-generic)
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[    0.000000]  BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000e6000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 00000000cf6b0000 (usable)
[    0.000000]  BIOS-e820: 00000000cf6b0000 - 00000000cf6c0000 (ACPI data)
[    0.000000]  BIOS-e820: 00000000cf6c0000 - 00000000cf6f0000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000cf6f0000 - 00000000cf700000 (reserved)
[    0.000000]  BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  BIOS-e820: 00000000ff380000 - 0000000100000000 (reserved)
[    0.000000] last_pfn = 0xcf6b0 max_arch_pfn = 0x100000
[    0.000000] kernel direct mapping tables up to 38000000 @ 7000-c000
[    0.000000] RAMDISK: 37782000 - 37fef110
[    0.000000] DMI present.
[    0.000000] ACPI: RSDP 000F9F50, 0014 (r0 ACPIAM)
[    0.000000] ACPI: RSDT CF6B0000, 003C (r1 082008 RSDT1949 20080820 MSFT       97)
[    0.000000] ACPI: FACP CF6B0200, 0084 (r1 A M I  OEMFACP  12000601 MSFT       97)
[    0.000000] ACPI: DSDT CF6B0440, 5779 (r1  AS153 AS153015       15 INTL 20051117)
[    0.000000] ACPI: FACS CF6C0000, 0040
[    0.000000] ACPI: APIC CF6B0390, 006C (r1 082008 APIC1949 20080820 MSFT       97)
[    0.000000] ACPI: MCFG CF6B0400, 003C (r1 082008 OEMMCFG  20080820 MSFT       97)
[    0.000000] ACPI: OEMB CF6C0040, 0071 (r1 082008 OEMB1949 20080820 MSFT       97)
[    0.000000] ACPI: GSCI CF6C00C0, 2024 (r1 082008 GMCHSCI  20080820 MSFT       97)
[    0.000000] ACPI: SSDT CF6C2A10, 0A7C (r1 DpgPmm    CpuPm       12 INTL 20051117)
[    0.000000] 2422MB HIGHMEM available.
[    0.000000] 896MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 38000000
[    0.000000]   low ram: 00000000 - 38000000
[    0.000000]   bootmap 00008000 - 0000f000
[    0.000000] (9 early reservations) ==> bootmem [0000000000 - 0038000000]
[    0.000000]   #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
[    0.000000]   #1 [0000001000 - 0000002000]    EX TRAMPOLINE ==> [0000001000 - 0000002000]
[    0.000000]   #2 [0000006000 - 0000007000]       TRAMPOLINE ==> [0000006000 - 0000007000]
[    0.000000]   #3 [0000100000 - 00005c0a20]    TEXT DATA BSS ==> [0000100000 - 00005c0a20]
[    0.000000]   #4 [0037782000 - 0037fef110]          RAMDISK ==> [0037782000 - 0037fef110]
[    0.000000]   #5 [00005c1000 - 00005c4000]    INIT_PG_TABLE ==> [00005c1000 - 00005c4000]
[    0.000000]   #6 [000009f800 - 0000100000]    BIOS reserved ==> [000009f800 - 0000100000]
[    0.000000]   #7 [0000007000 - 0000008000]          PGTABLE ==> [0000007000 - 0000008000]
[    0.000000]   #8 [0000008000 - 000000f000]          BOOTMAP ==> [0000008000 - 000000f000]
[    0.000000] found SMP MP-table at [c00ff780] 000ff780
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000000 -> 0x00001000
[    0.000000]   Normal   0x00001000 -> 0x00038000
[    0.000000]   HighMem  0x00038000 -> 0x000cf6b0
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[2] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x0000009f
[    0.000000]     0: 0x00000100 -> 0x000cf6b0
[    0.000000] On node 0 totalpages: 849487
[    0.000000] free_area_init_node: node 0, pgdat c048a580, node_mem_map c1000000
[    0.000000]   DMA zone: 3963 pages, LIFO batch:0
[    0.000000]   Normal zone: 223300 pages, LIFO batch:31
[    0.000000]   HighMem zone: 614756 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x808
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
[    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] SMP: Allowing 4 CPUs, 2 hotplug CPUs
[    0.000000] mapped APIC to ffffb000 (fee00000)
[    0.000000] mapped IOAPIC to ffffa000 (fec00000)
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e6000
[    0.000000] PM: Registered nosave memory: 00000000000e6000 - 0000000000100000
[    0.000000] Allocating PCI resources starting at d0000000 (gap: cf700000:2f600000)
[    0.000000] PERCPU: Allocating 41628 bytes of per cpu data
[    0.000000] NR_CPUS: 64, nr_cpu_ids: 4, nr_node_ids 1
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 842019
[    0.000000] Kernel command line: root=/dev/md2 ro quiet splash 
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[    0.000000] TSC: PIT calibration confirmed by PMTIMER.
[    0.000000] TSC: using PIT calibration value
[    0.000000] Detected 2493.733 MHz processor.
[    0.004000] Console: colour VGA+ 80x25
[    0.004000] console [tty0] enabled
[    0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.004000] Memory: 3352644k/3398336k available (2572k kernel code, 44452k reserved, 1160k data, 424k init, 2480832k highmem)
[    0.004000] virtual kernel memory layout:
[    0.004000]     fixmap  : 0xffc77000 - 0xfffff000   (3616 kB)
[    0.004000]     pkmap   : 0xff400000 - 0xff800000   (4096 kB)
[    0.004000]     vmalloc : 0xf8800000 - 0xff3fe000   ( 107 MB)
[    0.004000]     lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
[    0.004000]       .init : 0xc04ab000 - 0xc0515000   ( 424 kB)
[    0.004000]       .data : 0xc038335a - 0xc04a5680   (1160 kB)
[    0.004000]       .text : 0xc0100000 - 0xc038335a   (2572 kB)
[    0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[    0.004000] SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.004010] Calibrating delay loop (skipped), value calculated using timer frequency.. 4987.46 BogoMIPS (lpj=9974932)
[    0.004027] Security Framework initialized
[    0.004034] SELinux:  Disabled at boot.
[    0.004052] AppArmor: AppArmor initialized
[    0.004058] Mount-cache hash table entries: 512
[    0.004195] Initializing cgroup subsys ns
[    0.004199] Initializing cgroup subsys cpuacct
[    0.004201] Initializing cgroup subsys memory
[    0.004214] CPU: L1 I cache: 32K, L1 D cache: 32K
[    0.004216] CPU: L2 cache: 2048K
[    0.004218] CPU: Physical Processor ID: 0
[    0.004219] CPU: Processor Core ID: 0
[    0.004222] using mwait in idle threads.
[    0.004230] Checking 'hlt' instruction... OK.
[    0.021648] ACPI: Core revision 20080609
[    0.023590] ACPI: Checking initramfs for custom DSDT
[    0.311538] ENABLING IO-APIC IRQs
[    0.311706] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.351399] CPU0: Intel Pentium(R) Dual-Core  CPU      E5200  @ 2.50GHz stepping 06
[    0.352022] Booting processor 1/1 ip 6000
[    0.004000] Initializing CPU#1
[    0.004000] Calibrating delay using timer specific routine.. 4987.73 BogoMIPS (lpj=9975467)
[    0.004000] CPU: L1 I cache: 32K, L1 D cache: 32K
[    0.004000] CPU: L2 cache: 2048K
[    0.004000] CPU: Physical Processor ID: 0
[    0.004000] CPU: Processor Core ID: 1
[    0.436449] CPU1: Intel Pentium(R) Dual-Core  CPU      E5200  @ 2.50GHz stepping 06
[    0.436463] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[    0.440051] Brought up 2 CPUs
[    0.440054] Total of 2 processors activated (9975.19 BogoMIPS).
[    0.440074] CPU0 attaching sched-domain:
[    0.440076]  domain 0: span 0-1 level MC
[    0.440078]   groups: 0 1
[    0.440082] CPU1 attaching sched-domain:
[    0.440084]  domain 0: span 0-1 level MC
[    0.440086]   groups: 1 0
[    0.440150] net_namespace: 840 bytes
[    0.440150] Booting paravirtualized kernel on bare hardware
[    0.440237] Time: 12:19:41  Date: 12/08/08
[    0.440260] NET: Registered protocol family 16
[    0.440275] EISA bus registered
[    0.440275] ACPI: bus type pci registered
[    0.440275] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[    0.440275] PCI: Not using MMCONFIG.
[    0.440275] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=3
[    0.440275] PCI: Using configuration type 1 for base access
[    0.440712] ACPI: EC: Look up EC in DSDT
[    0.450595] ACPI: Interpreter enabled
[    0.450597] ACPI: (supports S0 S1 S3 S4 S5)
[    0.450611] ACPI: Using IOAPIC for interrupt routing
[    0.450661] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[    0.454480] PCI: MCFG area at e0000000 reserved in ACPI motherboard resources
[    0.454482] PCI: Using MMCONFIG for extended config space
[    0.460672] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    0.460672] PCI: 0000:00:02.0 reg 10 32bit mmio: [fe980000, fe9fffff]
[    0.460672] PCI: 0000:00:02.0 reg 14 io port: [dc00, dc07]
[    0.460672] PCI: 0000:00:02.0 reg 18 32bit mmio: [d0000000, dfffffff]
[    0.460672] PCI: 0000:00:02.0 reg 1c 32bit mmio: [fe800000, fe8fffff]
[    0.460672] PCI: 0000:00:1b.0 reg 10 64bit mmio: [fe978000, fe97bfff]
[    0.460672] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.460672] pci 0000:00:1b.0: PME# disabled
[    0.460672] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.460672] pci 0000:00:1c.0: PME# disabled
[    0.460672] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[    0.460672] pci 0000:00:1c.1: PME# disabled
[    0.460672] PCI: 0000:00:1d.0 reg 20 io port: [d400, d41f]
[    0.460672] PCI: 0000:00:1d.1 reg 20 io port: [d480, d49f]
[    0.460672] PCI: 0000:00:1d.2 reg 20 io port: [d800, d81f]
[    0.460672] PCI: 0000:00:1d.3 reg 20 io port: [d880, d89f]
[    0.460672] PCI: 0000:00:1d.7 reg 10 32bit mmio: [fe977c00, fe977fff]
[    0.460672] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[    0.460672] pci 0000:00:1d.7: PME# disabled
[    0.460672] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
[    0.460672] pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
[    0.460672] pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO
[    0.460672] PCI: 0000:00:1f.1 reg 10 io port: [0, 7]
[    0.460672] PCI: 0000:00:1f.1 reg 14 io port: [0, 3]
[    0.460672] PCI: 0000:00:1f.1 reg 18 io port: [8f0, 8f7]
[    0.460677] PCI: 0000:00:1f.1 reg 1c io port: [8f8, 8fb]
[    0.460683] PCI: 0000:00:1f.1 reg 20 io port: [ffa0, ffaf]
[    0.460717] PCI: 0000:00:1f.2 reg 10 io port: [d080, d087]
[    0.460722] PCI: 0000:00:1f.2 reg 14 io port: [d000, d003]
[    0.460727] PCI: 0000:00:1f.2 reg 18 io port: [cc00, cc07]
[    0.460732] PCI: 0000:00:1f.2 reg 1c io port: [c880, c883]
[    0.460737] PCI: 0000:00:1f.2 reg 20 io port: [c800, c80f]
[    0.460755] pci 0000:00:1f.2: PME# supported from D3hot
[    0.460758] pci 0000:00:1f.2: PME# disabled
[    0.460795] PCI: 0000:00:1f.3 reg 20 io port: [400, 41f]
[    0.460854] PCI: bridge 0000:00:1c.0 64bit mmio pref: [fdf00000, fdffffff]
[    0.460896] PCI: 0000:01:00.0 reg 10 io port: [e800, e8ff]
[    0.460909] PCI: 0000:01:00.0 reg 18 32bit mmio: [fdeff000, fdefffff]
[    0.460922] PCI: 0000:01:00.0 reg 20 32bit mmio: [fdee0000, fdeeffff]
[    0.460936] PCI: 0000:01:00.0 reg 30 32bit mmio: [feae0000, feafffff]
[    0.460962] pci 0000:01:00.0: supports D1
[    0.460963] pci 0000:01:00.0: supports D2
[    0.460964] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.460969] pci 0000:01:00.0: PME# disabled
[    0.460998] PCI: bridge 0000:00:1c.1 io port: [e000, efff]
[    0.461002] PCI: bridge 0000:00:1c.1 32bit mmio: [fea00000, feafffff]
[    0.461007] PCI: bridge 0000:00:1c.1 64bit mmio pref: [fde00000, fdefffff]
[    0.461038] PCI: 0000:03:01.0 reg 10 32bit mmio: [febfe000, febfefff]
[    0.461076] pci 0000:03:01.0: PME# supported from D0 D1 D3hot D3cold
[    0.461080] pci 0000:03:01.0: PME# disabled
[    0.461113] PCI: 0000:03:01.3 reg 10 32bit mmio: [febffc00, febffcff]
[    0.461153] pci 0000:03:01.3: PME# supported from D0 D3hot D3cold
[    0.461157] pci 0000:03:01.3: PME# disabled
[    0.461198] pci 0000:00:1e.0: transparent bridge
[    0.461203] PCI: bridge 0000:00:1e.0 32bit mmio: [feb00000, febfffff]
[    0.461220] bus 00 -> node 0
[    0.461225] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.461418] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[    0.461567] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
[    0.461666] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
[    0.464165] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[    0.464255] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[    0.464375] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[    0.464495] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[    0.464616] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[    0.464736] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[    0.464856] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[    0.464975] ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 7 10 11 12 14 15)
[    0.465029] ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - 4F, should be 42 [20080609]
[    0.465029] Linux Plug and Play Support v0.97 (c) Adam Belay
[    0.465029] pnp: PnP ACPI init
[    0.465029] ACPI: bus type pnp registered
[    0.472336] pnp: PnP ACPI: found 16 devices
[    0.472338] ACPI: ACPI bus type pnp unregistered
[    0.472341] PnPBIOS: Disabled by ACPI PNP
[    0.472354] PCI: Using ACPI for IRQ routing
[    0.480037] NET: Registered protocol family 8
[    0.480039] NET: Registered protocol family 20
[    0.480051] NetLabel: Initializing
[    0.480051] NetLabel:  domain hash size = 128
[    0.480051] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.480055] NetLabel:  unlabeled traffic allowed by default
[    0.480147] hpet clockevent registered
[    0.480151] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.480155] hpet0: 3 64-bit timers, 14318180 Hz
[    0.481858] tracer: 772 pages allocated for 65536 entries of 48 bytes
[    0.481861]    actual entries 65620
[    0.481934] AppArmor: AppArmor Filesystem Enabled
[    0.481951] ACPI: RTC can wake from S4
[    0.488045] system 00:01: iomem range 0xfed14000-0xfed19fff has been reserved
[    0.488053] system 00:08: ioport range 0x4d0-0x4d1 has been reserved
[    0.488056] system 00:08: ioport range 0x800-0x87f has been reserved
[    0.488058] system 00:08: ioport range 0x480-0x4bf has been reserved
[    0.488060] system 00:08: ioport range 0x900-0x90f has been reserved
[    0.488063] system 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved
[    0.488065] system 00:08: iomem range 0xfed20000-0xfed8ffff has been reserved
[    0.488071] system 00:0a: iomem range 0xffc00000-0xfff7ffff could not be reserved
[    0.488075] system 00:0b: iomem range 0xfec00000-0xfec00fff has been reserved
[    0.488077] system 00:0b: iomem range 0xfee00000-0xfee00fff could not be reserved
[    0.488083] system 00:0d: ioport range 0x290-0x29f has been reserved
[    0.488089] system 00:0e: iomem range 0xe0000000-0xefffffff has been reserved
[    0.488094] system 00:0f: iomem range 0x0-0x9ffff could not be reserved
[    0.488096] system 00:0f: iomem range 0xc0000-0xcffff could not be reserved
[    0.488098] system 00:0f: iomem range 0xe0000-0xfffff could not be reserved
[    0.488101] system 00:0f: iomem range 0x100000-0xcf6fffff could not be reserved
[    0.523015] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
[    0.523017] pci 0000:00:1c.0:   IO window: disabled
[    0.523021] pci 0000:00:1c.0:   MEM window: disabled
[    0.523024] pci 0000:00:1c.0:   PREFETCH window: 0x000000fdf00000-0x000000fdffffff
[    0.523030] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:01
[    0.523032] pci 0000:00:1c.1:   IO window: 0xe000-0xefff
[    0.523036] pci 0000:00:1c.1:   MEM window: 0xfea00000-0xfeafffff
[    0.523040] pci 0000:00:1c.1:   PREFETCH window: 0x000000fde00000-0x000000fdefffff
[    0.523045] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:03
[    0.523047] pci 0000:00:1e.0:   IO window: disabled
[    0.523051] pci 0000:00:1e.0:   MEM window: 0xfeb00000-0xfebfffff
[    0.523054] pci 0000:00:1e.0:   PREFETCH window: disabled
[    0.523066] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.523071] pci 0000:00:1c.0: setting latency timer to 64
[    0.523077] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[    0.523081] pci 0000:00:1c.1: setting latency timer to 64
[    0.523086] pci 0000:00:1e.0: setting latency timer to 64
[    0.523089] bus: 00 index 0 io port: [0, ffff]
[    0.523091] bus: 00 index 1 mmio: [0, ffffffff]
[    0.523092] bus: 02 index 0 mmio: [0, 0]
[    0.523094] bus: 02 index 1 mmio: [0, 0]
[    0.523095] bus: 02 index 2 mmio: [fdf00000, fdffffff]
[    0.523097] bus: 02 index 3 mmio: [0, 0]
[    0.523098] bus: 01 index 0 io port: [e000, efff]
[    0.523100] bus: 01 index 1 mmio: [fea00000, feafffff]
[    0.523102] bus: 01 index 2 mmio: [fde00000, fdefffff]
[    0.523103] bus: 01 index 3 mmio: [0, 0]
[    0.523105] bus: 03 index 0 mmio: [0, 0]
[    0.523106] bus: 03 index 1 mmio: [feb00000, febfffff]
[    0.523108] bus: 03 index 2 mmio: [0, 0]
[    0.523109] bus: 03 index 3 io port: [0, ffff]
[    0.523110] bus: 03 index 4 mmio: [0, ffffffff]
[    0.523117] NET: Registered protocol family 2
[    0.536074] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.536258] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.536584] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[    0.536773] TCP: Hash tables configured (established 131072 bind 65536)
[    0.536775] TCP reno registered
[    0.544094] NET: Registered protocol family 1
[    0.544185] checking if image is initramfs... it is
[    0.980508] Switched to high resolution mode on CPU 1
[    0.984057] Switched to high resolution mode on CPU 0
[    1.131885] Freeing initrd memory: 8628k freed
[    1.132846] audit: initializing netlink socket (disabled)
[    1.132867] type=2000 audit(1228738781.132:1): initialized
[    1.137720] highmem bounce pool size: 64 pages
[    1.137725] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    1.139519] VFS: Disk quotas dquot_6.5.1
[    1.139586] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.139672] msgmni has been set to 1721
[    1.139770] io scheduler noop registered
[    1.139772] io scheduler anticipatory registered
[    1.139774] io scheduler deadline registered
[    1.139784] io scheduler cfq registered (default)
[    1.139797] pci 0000:00:02.0: Boot video device
[    1.139981] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[    1.140012] pcieport-driver 0000:00:1c.0: found MSI capability
[    1.140043] pci_express 0000:00:1c.0:pcie00: allocate port service
[    1.140077] pci_express 0000:00:1c.0:pcie02: allocate port service
[    1.140107] pci_express 0000:00:1c.0:pcie03: allocate port service
[    1.140185] pcieport-driver 0000:00:1c.1: setting latency timer to 64
[    1.140213] pcieport-driver 0000:00:1c.1: found MSI capability
[    1.140242] pci_express 0000:00:1c.1:pcie00: allocate port service
[    1.140275] pci_express 0000:00:1c.1:pcie02: allocate port service
[    1.140305] pci_express 0000:00:1c.1:pcie03: allocate port service
[    1.140560] isapnp: Scanning for PnP cards...
[    1.494140] isapnp: No Plug & Play device found
[    1.519097] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[    1.519201] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.519776] 00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.521052] brd: module loaded
[    1.521103] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[    1.521240] PNP: No PS/2 controller found. Probing ports directly.
[    1.523478] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.523483] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.523681] mice: PS/2 mouse device common for all mice
[    1.523774] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[    1.523793] rtc0: alarms up to one month, y3k, hpet irqs
[    1.523892] EISA: Probing bus 0 at eisa.0
[    1.523916] EISA: Detected 0 cards.
[    1.523918] cpuidle: using governor ladder
[    1.523920] cpuidle: using governor menu
[    1.524316] TCP cubic registered
[    1.524337] Using IPI No-Shortcut mode
[    1.524470] registered taskstats version 1
[    1.524567]   Magic number: 4:181:329
[    1.524598] tty tty50: hash matches
[    1.524630] rtc_cmos 00:03: setting system clock to 2008-12-08 12:19:42 UTC (1228738782)
[    1.524633] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    1.524634] EDD information not available.
[    1.524820] Freeing unused kernel memory: 424k freed
[    1.524849] Write protecting the kernel text: 2576k
[    1.524870] Write protecting the kernel read-only data: 936k
[    1.628090] fuse init (API version 7.9)
[    1.676424] ACPI: SSDT CF6C20F0, 0277 (r1 DpgPmm  P001Ist       11 INTL 20051117)
[    1.676746] processor ACPI0007:00: registered as cooling_device0
[    1.677047] ACPI: SSDT CF6C2580, 0277 (r1 DpgPmm  P002Ist       12 INTL 20051117)
[    1.677348] processor ACPI0007:01: registered as cooling_device1
[    1.716633] md: linear personality registered for level -1
[    1.719563] md: multipath personality registered for level -4
[    1.732060] md: raid0 personality registered for level 0
[    1.740037] md: raid1 personality registered for level 1
[    1.742328] xor: automatically using best checksumming function: pIII_sse
[    1.760002]    pIII_sse  :  9232.000 MB/sec
[    1.760004] xor: using function: pIII_sse (9232.000 MB/sec)
[    1.761064] async_tx: api initialized (async)
[    1.832018] raid6: int32x1    919 MB/s
[    1.900037] raid6: int32x2    947 MB/s
[    1.968079] raid6: int32x4    735 MB/s
[    2.036087] raid6: int32x8    685 MB/s
[    2.104019] raid6: mmxx1     3112 MB/s
[    2.172015] raid6: mmxx2     3547 MB/s
[    2.240003] raid6: sse1x1    2094 MB/s
[    2.308020] raid6: sse1x2    2671 MB/s
[    2.376011] raid6: sse2x1    3784 MB/s
[    2.444014] raid6: sse2x2    4041 MB/s
[    2.444016] raid6: using algorithm sse2x2 (4041 MB/s)
[    2.444019] md: raid6 personality registered for level 6
[    2.444020] md: raid5 personality registered for level 5
[    2.444022] md: raid4 personality registered for level 4
[    2.461703] md: raid10 personality registered for level 10
[    2.654179] usbcore: registered new interface driver usbfs
[    2.654197] usbcore: registered new interface driver hub
[    2.654226] usbcore: registered new device driver usb
[    2.655834] USB Universal Host Controller Interface driver v3.0
[    2.655875] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    2.655882] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    2.655885] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    2.655918] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[    2.655944] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000d400
[    2.656063] usb usb1: configuration #1 chosen from 1 choice
[    2.656083] hub 1-0:1.0: USB hub found
[    2.656088] hub 1-0:1.0: 2 ports detected
[    2.700590] No dock devices found.
[    2.711941] SCSI subsystem initialized
[    2.728835] libata version 3.00 loaded.
[    2.728901] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.864330] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    2.864339] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    2.864342] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    2.864363] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[    2.864391] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000d480
[    2.864466] usb usb2: configuration #1 chosen from 1 choice
[    2.864491] hub 2-0:1.0: USB hub found
[    2.864497] hub 2-0:1.0: 2 ports detected
[    2.976514] usb 1-1: new low speed USB device using uhci_hcd and address 2
[    3.072355] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    3.072364] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    3.072367] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    3.072389] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[    3.072417] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000d800
[    3.072490] usb usb3: configuration #1 chosen from 1 choice
[    3.072513] hub 3-0:1.0: USB hub found
[    3.072518] hub 3-0:1.0: 2 ports detected
[    3.153126] usb 1-1: configuration #1 chosen from 1 choice
[    3.176278] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[    3.176284] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[    3.176287] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    3.176307] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[    3.176331] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000d880
[    3.176400] usb usb4: configuration #1 chosen from 1 choice
[    3.176421] hub 4-0:1.0: USB hub found
[    3.176425] hub 4-0:1.0: 2 ports detected
[    3.268008] usb 1-2: new low speed USB device using uhci_hcd and address 3
[    3.384389] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    3.384404] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[    3.384407] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    3.384736] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
[    3.388655] ehci_hcd 0000:00:1d.7: debug port 1
[    3.388661] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[    3.388668] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfe977c00
[    3.404515] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[    3.404640] usb usb5: configuration #1 chosen from 1 choice
[    3.404662] hub 5-0:1.0: USB hub found
[    3.404669] hub 5-0:1.0: 8 ports detected
[    3.419985] usb 1-2: device descriptor read/all, error -71
[    3.476033] hub 1-0:1.0: unable to enumerate USB device on port 2
[    3.612195] ata_piix 0000:00:1f.1: version 2.12
[    3.612207] ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    3.612241] ata_piix 0000:00:1f.1: setting latency timer to 64
[    3.612296] scsi0 : ata_piix
[    3.612364] scsi1 : ata_piix
[    3.613434] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[    3.613437] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[    3.934686] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    3.934689] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
[    3.934717] ata_piix 0000:00:1f.2: setting latency timer to 64
[    3.934751] scsi2 : ata_piix
[    3.935178] scsi3 : ata_piix
[    3.936757] ata3: SATA max UDMA/133 cmd 0xd080 ctl 0xd000 bmdma 0xc800 irq 19
[    3.936759] ata4: SATA max UDMA/133 cmd 0xcc00 ctl 0xc880 bmdma 0xc808 irq 19
[    3.956009] usb 5-3: new high speed USB device using ehci_hcd and address 4
[    4.089020] usb 5-3: configuration #1 chosen from 1 choice
[    4.108277] ata3.00: ATA-7: SAMSUNG HD252HJ, 1AC01113, max UDMA7
[    4.108280] ata3.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    4.108295] ata3.01: ATAPI: TSSTcorp CDDVDW SH-S223F, SB01, max UDMA/100
[    4.116281] ata3.00: configured for UDMA/133
[    4.132184] ata3.01: configured for UDMA/100
[    4.200016] usb 5-7: new high speed USB device using ehci_hcd and address 5
[    4.304275] ata4.00: ATA-7: SAMSUNG HD252HJ, 1AC01113, max UDMA7
[    4.304278] ata4.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    4.337720] usb 5-7: device descriptor read/all, error -71
[    4.344774] ata4.01: ATA-7: ST3500630NS, 3.AEE, max UDMA/133
[    4.344776] ata4.01: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    4.352283] ata4.00: configured for UDMA/133
[    4.428081] ata4.01: configured for UDMA/133
[    4.428166] scsi 2:0:0:0: Direct-Access     ATA      SAMSUNG HD252HJ  1AC0 PQ: 0 ANSI: 5
[    4.428829] scsi 2:0:1:0: CD-ROM            TSSTcorp CDDVDW SH-S223F  SB01 PQ: 0 ANSI: 5
[    4.428933] scsi 3:0:0:0: Direct-Access     ATA      SAMSUNG HD252HJ  1AC0 PQ: 0 ANSI: 5
[    4.429028] scsi 3:0:1:0: Direct-Access     ATA      ST3500630NS      3.AE PQ: 0 ANSI: 5
[    4.429092] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    4.429104] r8169 0000:01:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    4.429117] r8169 0000:01:00.0: setting latency timer to 64
[    4.429128] r8169 0000:01:00.0: unknown MAC (27a00000)
[    4.429393] eth0: RTL8169 at 0xf891e000, 00:19:66:95:4c:ba, XID 24a00000 IRQ 221
[    4.430258] ehci_hcd 0000:03:01.3: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[    4.430265] ehci_hcd 0000:03:01.3: EHCI Host Controller
[    4.430287] ehci_hcd 0000:03:01.3: new USB bus registered, assigned bus number 6
[    4.452011] usb 5-7: new high speed USB device using ehci_hcd and address 6
[    4.452017] ehci_hcd 0000:03:01.3: debug port 1
[    4.452029] ehci_hcd 0000:03:01.3: irq 22, io mem 0xfebffc00
[    4.464009] ehci_hcd 0000:03:01.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[    4.464102] usb usb6: configuration #1 chosen from 1 choice
[    4.464124] hub 6-0:1.0: USB hub found
[    4.464130] hub 6-0:1.0: 6 ports detected
[    4.568119] ohci_hcd 0000:03:01.0: PCI INT B -> GSI 23 (level, low) -> IRQ 23
[    4.568127] ohci_hcd 0000:03:01.0: OHCI Host Controller
[    4.568146] ohci_hcd 0000:03:01.0: new USB bus registered, assigned bus number 7
[    4.568156] ohci_hcd 0000:03:01.0: irq 23, io mem 0xfebfe000
[    4.598445] usb 5-7: configuration #1 chosen from 1 choice
[    4.598872] usb 1-1: USB disconnect, address 2
[    4.599073] usbcore: registered new interface driver hiddev
[    4.600058] usbcore: registered new interface driver libusual
[    4.609331] Initializing USB Mass Storage driver...
[    4.626120] usb usb7: configuration #1 chosen from 1 choice
[    4.626145] hub 7-0:1.0: USB hub found
[    4.626152] hub 7-0:1.0: 2 ports detected
[    4.741316] scsi 2:0:0:0: Attached scsi generic sg0 type 0
[    4.741346] scsi 2:0:1:0: Attached scsi generic sg1 type 5
[    4.741373] scsi 3:0:0:0: Attached scsi generic sg2 type 0
[    4.741402] scsi 3:0:1:0: Attached scsi generic sg3 type 0
[    4.756893] Driver 'sr' needs updating - please use bus_type methods
[    4.760732] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[    4.760736] Uniform CD-ROM driver Revision: 3.20
[    4.760814] sr 2:0:1:0: Attached scsi CD-ROM sr0
[    4.774182] Driver 'sd' needs updating - please use bus_type methods
[    4.774412] sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
[    4.774428] sd 2:0:0:0: [sda] Write Protect is off
[    4.774430] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    4.774453] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.774511] sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
[    4.774524] sd 2:0:0:0: [sda] Write Protect is off
[    4.774526] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    4.774548] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.774551]  sda: sda1 sda2 sda3 < sda5 >
[    4.789601] sd 2:0:0:0: [sda] Attached SCSI disk
[    4.789659] sd 3:0:0:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
[    4.789674] sd 3:0:0:0: [sdb] Write Protect is off
[    4.789676] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    4.789701] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.789782] sd 3:0:0:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
[    4.789796] sd 3:0:0:0: [sdb] Write Protect is off
[    4.789798] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    4.789823] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.789826]  sdb: sdb1 sdb2 sdb3 < sdb5 >
[    4.804791] sd 3:0:0:0: [sdb] Attached SCSI disk
[    4.804851] sd 3:0:1:0: [sdc] 976773168 512-byte hardware sectors (500108 MB)
[    4.804867] sd 3:0:1:0: [sdc] Write Protect is off
[    4.804869] sd 3:0:1:0: [sdc] Mode Sense: 00 3a 00 00
[    4.804894] sd 3:0:1:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.804941] sd 3:0:1:0: [sdc] 976773168 512-byte hardware sectors (500108 MB)
[    4.804955] sd 3:0:1:0: [sdc] Write Protect is off
[    4.804957] sd 3:0:1:0: [sdc] Mode Sense: 00 3a 00 00
[    4.804982] sd 3:0:1:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.804985]  sdc: sdc1
[    4.817669] sd 3:0:1:0: [sdc] Attached SCSI disk
[    4.836488] usb 1-1: new low speed USB device using uhci_hcd and address 5
[    4.954335] md: md0 stopped.
[    5.017105] usb 1-1: configuration #1 chosen from 1 choice
[    5.078462] md: bind<sda1>
[    5.078595] md: md1 stopped.
[    5.112925] md: bind<sda2>
[    5.113057] md: md2 stopped.
[    5.122561] md: bind<sdb5>
[    5.122703] md: bind<sda5>
[    5.129211] raid1: raid set md2 active with 2 out of 2 mirrors
[    5.180930] md: md0 stopped.
[    5.180941] md: unbind<sda1>
[    5.188011] md: export_rdev(sda1)
[    5.212318] md: bind<sdb1>
[    5.212460] md: bind<sda1>
[    5.219773] raid1: raid set md0 active with 2 out of 2 mirrors
[    5.219834] md: md1 stopped.
[    5.219842] md: unbind<sda2>
[    5.220289] md: export_rdev(sda2)
[    5.227702] md: bind<sdb2>
[    5.227845] md: bind<sda2>
[    5.234981] raid1: raid set md1 active with 2 out of 2 mirrors
[    5.264018] usb 1-2: new low speed USB device using uhci_hcd and address 6
[    5.431104] usb 1-2: configuration #1 chosen from 1 choice
[    5.435009] scsi4 : SCSI emulation for USB Mass Storage devices
[    5.437711] usb-storage: device found at 4
[    5.437713] usb-storage: waiting for device to settle before scanning
[    5.437851] scsi5 : SCSI emulation for USB Mass Storage devices
[    5.437922] usb-storage: device found at 6
[    5.437923] usb-storage: waiting for device to settle before scanning
[    5.449231] input: CHESEN USB Keyboard as /devices/pci0000:00/0000:00:1d.0/usb1/1-1/1-1:1.0/input/input1
[    5.449425] input,hidraw0: USB HID v1.10 Keyboard [CHESEN USB Keyboard] on usb-0000:00:1d.0-1
[    5.475048] input: CHESEN USB Keyboard as /devices/pci0000:00/0000:00:1d.0/usb1/1-1/1-1:1.1/input/input2
[    5.475205] input,hidraw1: USB HID v1.10 Device [CHESEN USB Keyboard] on usb-0000:00:1d.0-1
[    5.488148] input: USB Mouse as /devices/pci0000:00/0000:00:1d.0/usb1/1-2/1-2:1.0/input/input3
[    5.488317] input,hidraw2: USB HID v1.10 Mouse [USB Mouse] on usb-0000:00:1d.0-2
[    5.488343] usbcore: registered new interface driver usb-storage
[    5.488346] USB Mass Storage support registered.
[    5.488437] usbcore: registered new interface driver usbhid
[    5.488440] usbhid: v2.6:USB HID core driver
[    5.583897] PM: Starting manual resume from disk
[    5.583900] PM: Resume from partition 9:1
[    5.583902] PM: Checking hibernation image.
[    5.584038] PM: Resume from disk failed.
[    5.622098] kjournald starting.  Commit interval 5 seconds
[    5.622107] EXT3-fs: mounted filesystem with ordered data mode.
[   10.155866] udevd version 124 started
[   10.375742] Linux agpgart interface v0.103
[   10.424239] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   10.444149] usb-storage: device scan complete
[   10.444618] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   10.445167] scsi 4:0:0:0: Direct-Access     WDC      WD1600BB-00DWA0  15.0 PQ: 0 ANSI: 2
[   10.465218] usb-storage: device scan complete
[   10.466180] scsi 5:0:0:0: Direct-Access     Generic  USB SD Reader    1.00 PQ: 0 ANSI: 0
[   10.466658] scsi 5:0:0:1: Direct-Access     Generic  USB CF Reader    1.01 PQ: 0 ANSI: 0
[   10.467155] scsi 5:0:0:2: Direct-Access     Generic  USB SM Reader    1.02 PQ: 0 ANSI: 0
[   10.467656] scsi 5:0:0:3: Direct-Access     Generic  USB MS Reader    1.03 PQ: 0 ANSI: 0
[   10.489395] sd 4:0:0:0: [sdd] 312581808 512-byte hardware sectors (160042 MB)
[   10.490142] sd 4:0:0:0: [sdd] Write Protect is off
[   10.490144] sd 4:0:0:0: [sdd] Mode Sense: 53 00 00 08
[   10.490146] sd 4:0:0:0: [sdd] Assuming drive cache: write through
[   10.490660] agpgart-intel 0000:00:00.0: Intel G33 Chipset
[   10.491170] agpgart-intel 0000:00:00.0: detected 7164K stolen memory
[   10.491276] sd 4:0:0:0: [sdd] 312581808 512-byte hardware sectors (160042 MB)
[   10.505835] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
[   10.593082] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[   10.604571] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   10.616515] ACPI: Power Button (FF) [PWRF]
[   10.616610] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input5
[   10.644524] ACPI: Power Button (CM) [PWRB]
[   10.778825] parport_pc 00:07: reported by Plug and Play ACPI
[   10.778879] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[   11.152450] iTCO_vendor_support: vendor-support=0
[   11.154805] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[   11.154870] iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0860)
[   11.154953] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   11.176462] intel_rng: FWH not detected
[   11.227585] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   11.227602] HDA Intel 0000:00:1b.0: setting latency timer to 64
[   11.258414] hda_codec: Unknown model for ALC662, trying auto-probe from BIOS...
[   11.291809] input: PC Speaker as /devices/platform/pcspkr/input/input6
[   11.314358] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   11.576614] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   12.276011] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   12.528014] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   12.788009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   12.920671] sd 4:0:0:0: [sdd] Write Protect is off
[   12.920673] sd 4:0:0:0: [sdd] Mode Sense: 00 00 00 00
[   12.920675] sd 4:0:0:0: [sdd] Assuming drive cache: write through
[   12.920681]  sdd:<6>usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   13.292008] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   13.540012] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   13.788008] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   14.036008] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   14.284008] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   14.416670] sd 4:0:0:0: [sdd] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[   14.416674] end_request: I/O error, dev sdd, sector 0
[   14.416677] Buffer I/O error on device sdd, logical block 0
[   14.552009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   14.800009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   15.052009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   15.300009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   15.548009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   15.812008] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   15.944555] sd 4:0:0:0: [sdd] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[   15.944559] end_request: I/O error, dev sdd, sector 0
[   15.944561] Buffer I/O error on device sdd, logical block 0
[   16.060009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   16.308009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   16.556009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   16.804009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   17.068008] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   17.320009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   17.452566] sd 4:0:0:0: [sdd] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[   17.452569] end_request: I/O error, dev sdd, sector 0
[   17.452571] Buffer I/O error on device sdd, logical block 0
[   17.576509] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   17.824009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   18.076009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   18.324009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   18.580009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   18.828009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   18.960576] sd 4:0:0:0: [sdd] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[   18.960579] end_request: I/O error, dev sdd, sector 0
[   18.960581] Buffer I/O error on device sdd, logical block 0
[   19.080009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   19.336509] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   19.592009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   19.840009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   20.088009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   20.336509] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   20.468587] sd 4:0:0:0: [sdd] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[   20.468590] end_request: I/O error, dev sdd, sector 0
[   20.468592] Buffer I/O error on device sdd, logical block 0
[   20.468600] ldm_validate_partition_table(): Disk read failed.
[   20.584509] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   20.836008] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   21.084509] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   21.340009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   21.592009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   21.844008] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   21.977096] sd 4:0:0:0: [sdd] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[   21.977099] end_request: I/O error, dev sdd, sector 0
[   21.977101] Buffer I/O error on device sdd, logical block 0
[   22.096509] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   22.344009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   22.592009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   22.840009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   23.112009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   23.360009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   23.492607] sd 4:0:0:0: [sdd] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[   23.492610] end_request: I/O error, dev sdd, sector 0
[   23.492612] Buffer I/O error on device sdd, logical block 0
[   23.608009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   23.876008] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   24.124009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   24.372009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   24.620009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   24.868009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   25.000617] sd 4:0:0:0: [sdd] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[   25.000620] end_request: I/O error, dev sdd, sector 0
[   25.000622] Buffer I/O error on device sdd, logical block 0
[   25.136008] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   25.384509] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   25.632508] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   25.888009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   26.140009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   26.388009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   26.520753] sd 4:0:0:0: [sdd] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[   26.520756] end_request: I/O error, dev sdd, sector 0
[   26.520758] Buffer I/O error on device sdd, logical block 0
[   26.520767] Dev sdd: unable to read RDB block 0
[   26.636009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   26.892009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   27.144009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   27.392009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   27.640009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   27.904008] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   28.037138] sd 4:0:0:0: [sdd] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[   28.037141] end_request: I/O error, dev sdd, sector 0
[   28.037144] Buffer I/O error on device sdd, logical block 0
[   28.164008] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   28.412009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   28.660009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   28.912009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   29.160009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   29.408009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   29.540774] sd 4:0:0:0: [sdd] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[   29.540777] end_request: I/O error, dev sdd, sector 0
[   29.540779] Buffer I/O error on device sdd, logical block 0
[   29.656509] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   29.904009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   30.152009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   30.400009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   30.648009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   30.896509] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   31.028659] sd 4:0:0:0: [sdd] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[   31.028662] end_request: I/O error, dev sdd, sector 24
[   31.028664] Buffer I/O error on device sdd, logical block 3
[   31.144009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   31.392009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   31.640009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   31.888009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   32.136509] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   32.384508] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   32.516669] sd 4:0:0:0: [sdd] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[   32.516672] end_request: I/O error, dev sdd, sector 24
[   32.516674] Buffer I/O error on device sdd, logical block 3
[   32.632009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   32.880009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   33.128008] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   33.380009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   33.628009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   33.896008] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   34.028680] sd 4:0:0:0: [sdd] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[   34.028683] end_request: I/O error, dev sdd, sector 0
[   34.028685] Buffer I/O error on device sdd, logical block 0
[   34.144009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   64.388509] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   64.636008] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   64.884009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   65.132009] usb 5-3: reset high speed USB device using ehci_hcd and address 4
[   65.264645] sd 4:0:0:0: Device offlined - not ready after error recovery
[   65.264648] sd 4:0:0:0: [sdd] Result: hostbyte=DID_ABORT driverbyte=DRIVER_OK,SUGGEST_OK
[   65.264651] end_request: I/O error, dev sdd, sector 0
[   65.264654] Buffer I/O error on device sdd, logical block 0
[   65.264663]  unable to read partition table
[   65.265000] sd 4:0:0:0: [sdd] Attached SCSI disk
[   65.265319] sd 4:0:0:0: Attached scsi generic sg4 type 0
[   65.266210] sd 5:0:0:0: [sde] Attached SCSI removable disk
[   65.266271] sd 5:0:0:0: Attached scsi generic sg5 type 0
[   65.267098] sd 5:0:0:1: [sdf] Attached SCSI removable disk
[   65.267174] sd 5:0:0:1: Attached scsi generic sg6 type 0
[   65.267975] sd 5:0:0:2: [sdg] Attached SCSI removable disk
[   65.268069] sd 5:0:0:2: Attached scsi generic sg7 type 0
[   65.268991] sd 5:0:0:3: [sdh] Attached SCSI removable disk
[   65.269086] sd 5:0:0:3: Attached scsi generic sg8 type 0
[   66.142888] loop: module loaded
[   66.151696] lp0: using parport0 (interrupt-driven).
[   66.269928] Adding 4883640k swap on /dev/md1.  Priority:-1 extents:1 across:4883640k
[   66.830925] EXT3 FS on md2, internal journal
[   67.031342] device-mapper: uevent: version 1.0.3
[   67.031482] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[   67.794050] kjournald starting.  Commit interval 5 seconds
[   67.813531] EXT3 FS on md0, internal journal
[   67.813535] EXT3-fs: mounted filesystem with ordered data mode.
[   68.048904] type=1505 audit(1228738848.995:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=4497
[   68.175865] type=1505 audit(1228738849.119:3): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=4502
[   68.176043] type=1505 audit(1228738849.119:4): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=4502
[   68.335845] ip_tables: (C) 2000-2006 Netfilter Core Team
[   68.758921] ACPI: WMI: Mapper loaded
[   69.549027] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
[   69.745525] NET: Registered protocol family 10
[   69.746017] lo: Disabled Privacy Extensions
[   69.823641] apm: BIOS version 1.2 Flags 0x02 (Driver version 1.16ac)
[   69.823646] apm: disabled - APM is not SMP safe.
[   71.099958] Bluetooth: Core ver 2.13
[   71.100427] NET: Registered protocol family 31
[   71.100435] Bluetooth: HCI device and connection manager initialized
[   71.100439] Bluetooth: HCI socket layer initialized
[   71.167775] Bluetooth: L2CAP ver 2.11
[   71.167785] Bluetooth: L2CAP socket layer initialized
[   71.189566] Bluetooth: SCO (Voice Link) ver 0.6
[   71.189577] Bluetooth: SCO socket layer initialized
[   71.218340] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   71.218349] Bluetooth: BNEP filters: protocol multicast
[   71.252399] Bridge firewalling registered
[   71.253238] pan0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
[   71.330790] Bluetooth: RFCOMM socket layer initialized
[   71.330808] Bluetooth: RFCOMM TTY layer initialized
[   71.330811] Bluetooth: RFCOMM ver 1.10
[   73.960233] [drm] Initialized drm 1.1.0 20060810
[   73.982714] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   73.982727] pci 0000:00:02.0: setting latency timer to 64
[   73.982902] [drm] Initialized i915 1.6.0 20060119 on minor 0
[   74.415216] set status page addr 0x00033000
[   75.456668] r8169: eth0: link up
[   75.456682] r8169: eth0: link up
[   75.615811] NET: Registered protocol family 17
[   85.624010] eth0: no IPv6 routers present
[ 5260.904018] usb 5-5: new high speed USB device using ehci_hcd and address 7
[ 5261.039876] usb 5-5: configuration #1 chosen from 1 choice
[ 5261.073383] scsi6 : SCSI emulation for USB Mass Storage devices
[ 5261.079491] usb-storage: device found at 7
[ 5261.079500] usb-storage: waiting for device to settle before scanning
[ 5266.077133] usb-storage: device scan complete
[ 5266.078130] scsi 6:0:0:0: Direct-Access     Kingston DataTraveler 2.0 1.00 PQ: 0 ANSI: 2
[ 5266.080847] sd 6:0:0:0: [sdi] 1952768 512-byte hardware sectors (1000 MB)
[ 5266.081343] sd 6:0:0:0: [sdi] Write Protect is off
[ 5266.081348] sd 6:0:0:0: [sdi] Mode Sense: 23 00 00 00
[ 5266.081352] sd 6:0:0:0: [sdi] Assuming drive cache: write through
[ 5266.083599] sd 6:0:0:0: [sdi] 1952768 512-byte hardware sectors (1000 MB)
[ 5296.192026] usb 5-5: reset high speed USB device using ehci_hcd and address 7
[ 5296.326066] sd 6:0:0:0: [sdi] Write Protect is off
[ 5296.326076] sd 6:0:0:0: [sdi] Mode Sense: 23 00 00 00
[ 5296.326080] sd 6:0:0:0: [sdi] Assuming drive cache: write through
[ 5296.326090]  sdi: sdi1
[ 5296.432930] sd 6:0:0:0: [sdi] Attached SCSI removable disk
[ 5296.433084] sd 6:0:0:0: Attached scsi generic sg9 type 0
[ 5326.676028] usb 5-5: reset high speed USB device using ehci_hcd and address 7
[ 5334.408845] usb 5-5: USB disconnect, address 7
[ 5334.464379] sd 6:0:0:0: [sdi] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[ 5334.464391] end_request: I/O error, dev sdi, sector 1952764
[ 5334.464399] Buffer I/O error on device sdi1, logical block 244079
[ 5334.467429] scsi 6:0:0:0: rejecting I/O to dead device
[ 5334.467449] scsi 6:0:0:0: rejecting I/O to dead device
[ 5334.467456] scsi 6:0:0:0: [sdi] READ CAPACITY failed
[ 5334.467459] scsi 6:0:0:0: [sdi] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_OK
[ 5334.467465] scsi 6:0:0:0: [sdi] Sense not available.
[ 5334.467472] scsi 6:0:0:0: rejecting I/O to dead device
[ 5334.467479] scsi 6:0:0:0: [sdi] Write Protect is off
[ 5334.467483] scsi 6:0:0:0: [sdi] Mode Sense: 00 00 00 00
[ 5334.467487] scsi 6:0:0:0: [sdi] Assuming drive cache: write through
[ 5334.469295] Buffer I/O error on device sdi1, logical block 244079
[ 5334.469337] Buffer I/O error on device sdi1, logical block 244079
[ 5334.469358] Buffer I/O error on device sdi1, logical block 244079
[ 5334.469377] Buffer I/O error on device sdi1, logical block 244079
[ 5334.469396] Buffer I/O error on device sdi1, logical block 244079
[ 5334.469416] Buffer I/O error on device sdi1, logical block 244079
[ 5334.469441] Buffer I/O error on device sdi1, logical block 244072
[ 5334.469463] Buffer I/O error on device sdi1, logical block 244078
[ 5334.469484] Buffer I/O error on device sdi1, logical block 244079

******************* dmesg output ************* WORKS

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.27-9-generic (buildd@rothera) (gcc version 4.3.2 (Ubuntu 4.3.2-1ubuntu11) ) #1 SMP Thu Nov 20 21:57:00 UTC 2008 (Ubuntu 2.6.27-9.19-generic)
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[    0.000000]  BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000e6000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 00000000cf6b0000 (usable)
[    0.000000]  BIOS-e820: 00000000cf6b0000 - 00000000cf6c0000 (ACPI data)
[    0.000000]  BIOS-e820: 00000000cf6c0000 - 00000000cf6f0000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000cf6f0000 - 00000000cf700000 (reserved)
[    0.000000]  BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  BIOS-e820: 00000000ff380000 - 0000000100000000 (reserved)
[    0.000000] last_pfn = 0xcf6b0 max_arch_pfn = 0x100000
[    0.000000] kernel direct mapping tables up to 38000000 @ 7000-c000
[    0.000000] RAMDISK: 37782000 - 37fef110
[    0.000000] DMI present.
[    0.000000] ACPI: RSDP 000F9F50, 0014 (r0 ACPIAM)
[    0.000000] ACPI: RSDT CF6B0000, 003C (r1 082008 RSDT1949 20080820 MSFT       97)
[    0.000000] ACPI: FACP CF6B0200, 0084 (r1 A M I  OEMFACP  12000601 MSFT       97)
[    0.000000] ACPI: DSDT CF6B0440, 5779 (r1  AS153 AS153015       15 INTL 20051117)
[    0.000000] ACPI: FACS CF6C0000, 0040
[    0.000000] ACPI: APIC CF6B0390, 006C (r1 082008 APIC1949 20080820 MSFT       97)
[    0.000000] ACPI: MCFG CF6B0400, 003C (r1 082008 OEMMCFG  20080820 MSFT       97)
[    0.000000] ACPI: OEMB CF6C0040, 0071 (r1 082008 OEMB1949 20080820 MSFT       97)
[    0.000000] ACPI: GSCI CF6C00C0, 2024 (r1 082008 GMCHSCI  20080820 MSFT       97)
[    0.000000] ACPI: SSDT CF6C2A10, 0A7C (r1 DpgPmm    CpuPm       12 INTL 20051117)
[    0.000000] 2422MB HIGHMEM available.
[    0.000000] 896MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 38000000
[    0.000000]   low ram: 00000000 - 38000000
[    0.000000]   bootmap 00008000 - 0000f000
[    0.000000] (9 early reservations) ==> bootmem [0000000000 - 0038000000]
[    0.000000]   #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
[    0.000000]   #1 [0000001000 - 0000002000]    EX TRAMPOLINE ==> [0000001000 - 0000002000]
[    0.000000]   #2 [0000006000 - 0000007000]       TRAMPOLINE ==> [0000006000 - 0000007000]
[    0.000000]   #3 [0000100000 - 00005c0a20]    TEXT DATA BSS ==> [0000100000 - 00005c0a20]
[    0.000000]   #4 [0037782000 - 0037fef110]          RAMDISK ==> [0037782000 - 0037fef110]
[    0.000000]   #5 [00005c1000 - 00005c4000]    INIT_PG_TABLE ==> [00005c1000 - 00005c4000]
[    0.000000]   #6 [000009f800 - 0000100000]    BIOS reserved ==> [000009f800 - 0000100000]
[    0.000000]   #7 [0000007000 - 0000008000]          PGTABLE ==> [0000007000 - 0000008000]
[    0.000000]   #8 [0000008000 - 000000f000]          BOOTMAP ==> [0000008000 - 000000f000]
[    0.000000] found SMP MP-table at [c00ff780] 000ff780
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000000 -> 0x00001000
[    0.000000]   Normal   0x00001000 -> 0x00038000
[    0.000000]   HighMem  0x00038000 -> 0x000cf6b0
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[2] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x0000009f
[    0.000000]     0: 0x00000100 -> 0x000cf6b0
[    0.000000] On node 0 totalpages: 849487
[    0.000000] free_area_init_node: node 0, pgdat c048a580, node_mem_map c1000000
[    0.000000]   DMA zone: 3963 pages, LIFO batch:0
[    0.000000]   Normal zone: 223300 pages, LIFO batch:31
[    0.000000]   HighMem zone: 614756 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x808
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
[    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] SMP: Allowing 4 CPUs, 2 hotplug CPUs
[    0.000000] mapped APIC to ffffb000 (fee00000)
[    0.000000] mapped IOAPIC to ffffa000 (fec00000)
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e6000
[    0.000000] PM: Registered nosave memory: 00000000000e6000 - 0000000000100000
[    0.000000] Allocating PCI resources starting at d0000000 (gap: cf700000:2f600000)
[    0.000000] PERCPU: Allocating 41628 bytes of per cpu data
[    0.000000] NR_CPUS: 64, nr_cpu_ids: 4, nr_node_ids 1
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 842019
[    0.000000] Kernel command line: root=/dev/md2 ro quiet splash 
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[    0.000000] TSC: PIT calibration confirmed by PMTIMER.
[    0.000000] TSC: using PMTIMER calibration value
[    0.000000] Detected 2493.740 MHz processor.
[    0.004000] Console: colour VGA+ 80x25
[    0.004000] console [tty0] enabled
[    0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.004000] Memory: 3352644k/3398336k available (2572k kernel code, 44452k reserved, 1160k data, 424k init, 2480832k highmem)
[    0.004000] virtual kernel memory layout:
[    0.004000]     fixmap  : 0xffc77000 - 0xfffff000   (3616 kB)
[    0.004000]     pkmap   : 0xff400000 - 0xff800000   (4096 kB)
[    0.004000]     vmalloc : 0xf8800000 - 0xff3fe000   ( 107 MB)
[    0.004000]     lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
[    0.004000]       .init : 0xc04ab000 - 0xc0515000   ( 424 kB)
[    0.004000]       .data : 0xc038335a - 0xc04a5680   (1160 kB)
[    0.004000]       .text : 0xc0100000 - 0xc038335a   (2572 kB)
[    0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[    0.004000] SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.004010] Calibrating delay loop (skipped), value calculated using timer frequency.. 4987.48 BogoMIPS (lpj=9974960)
[    0.004027] Security Framework initialized
[    0.004034] SELinux:  Disabled at boot.
[    0.004050] AppArmor: AppArmor initialized
[    0.004058] Mount-cache hash table entries: 512
[    0.004196] Initializing cgroup subsys ns
[    0.004200] Initializing cgroup subsys cpuacct
[    0.004203] Initializing cgroup subsys memory
[    0.004215] CPU: L1 I cache: 32K, L1 D cache: 32K
[    0.004217] CPU: L2 cache: 2048K
[    0.004219] CPU: Physical Processor ID: 0
[    0.004221] CPU: Processor Core ID: 0
[    0.004224] using mwait in idle threads.
[    0.004231] Checking 'hlt' instruction... OK.
[    0.021649] ACPI: Core revision 20080609
[    0.023592] ACPI: Checking initramfs for custom DSDT
[    0.311476] ENABLING IO-APIC IRQs
[    0.311645] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.351336] CPU0: Intel Pentium(R) Dual-Core  CPU      E5200  @ 2.50GHz stepping 06
[    0.352022] Booting processor 1/1 ip 6000
[    0.004000] Initializing CPU#1
[    0.004000] Calibrating delay using timer specific routine.. 4987.74 BogoMIPS (lpj=9975487)
[    0.004000] CPU: L1 I cache: 32K, L1 D cache: 32K
[    0.004000] CPU: L2 cache: 2048K
[    0.004000] CPU: Physical Processor ID: 0
[    0.004000] CPU: Processor Core ID: 1
[    0.436448] CPU1: Intel Pentium(R) Dual-Core  CPU      E5200  @ 2.50GHz stepping 06
[    0.436462] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[    0.440051] Brought up 2 CPUs
[    0.440053] Total of 2 processors activated (9975.22 BogoMIPS).
[    0.440072] CPU0 attaching sched-domain:
[    0.440074]  domain 0: span 0-1 level MC
[    0.440076]   groups: 0 1
[    0.440081] CPU1 attaching sched-domain:
[    0.440083]  domain 0: span 0-1 level MC
[    0.440085]   groups: 1 0
[    0.440147] net_namespace: 840 bytes
[    0.440147] Booting paravirtualized kernel on bare hardware
[    0.440237] Time: 13:51:39  Date: 12/08/08
[    0.440259] NET: Registered protocol family 16
[    0.440275] EISA bus registered
[    0.440275] ACPI: bus type pci registered
[    0.440275] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[    0.440275] PCI: Not using MMCONFIG.
[    0.440275] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=3
[    0.440275] PCI: Using configuration type 1 for base access
[    0.440713] ACPI: EC: Look up EC in DSDT
[    0.450615] ACPI: Interpreter enabled
[    0.450618] ACPI: (supports S0 S1 S3 S4 S5)
[    0.450630] ACPI: Using IOAPIC for interrupt routing
[    0.450681] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[    0.454498] PCI: MCFG area at e0000000 reserved in ACPI motherboard resources
[    0.454500] PCI: Using MMCONFIG for extended config space
[    0.460687] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    0.460687] PCI: 0000:00:02.0 reg 10 32bit mmio: [fe980000, fe9fffff]
[    0.460687] PCI: 0000:00:02.0 reg 14 io port: [dc00, dc07]
[    0.460687] PCI: 0000:00:02.0 reg 18 32bit mmio: [d0000000, dfffffff]
[    0.460687] PCI: 0000:00:02.0 reg 1c 32bit mmio: [fe800000, fe8fffff]
[    0.460687] PCI: 0000:00:1b.0 reg 10 64bit mmio: [fe978000, fe97bfff]
[    0.460687] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.460687] pci 0000:00:1b.0: PME# disabled
[    0.460687] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.460687] pci 0000:00:1c.0: PME# disabled
[    0.460687] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[    0.460687] pci 0000:00:1c.1: PME# disabled
[    0.460687] PCI: 0000:00:1d.0 reg 20 io port: [d400, d41f]
[    0.460687] PCI: 0000:00:1d.1 reg 20 io port: [d480, d49f]
[    0.460687] PCI: 0000:00:1d.2 reg 20 io port: [d800, d81f]
[    0.460687] PCI: 0000:00:1d.3 reg 20 io port: [d880, d89f]
[    0.460687] PCI: 0000:00:1d.7 reg 10 32bit mmio: [fe977c00, fe977fff]
[    0.460687] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[    0.460687] pci 0000:00:1d.7: PME# disabled
[    0.460687] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
[    0.460687] pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
[    0.460687] pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO
[    0.460687] PCI: 0000:00:1f.1 reg 10 io port: [0, 7]
[    0.460687] PCI: 0000:00:1f.1 reg 14 io port: [0, 3]
[    0.460687] PCI: 0000:00:1f.1 reg 18 io port: [8f0, 8f7]
[    0.460687] PCI: 0000:00:1f.1 reg 1c io port: [8f8, 8fb]
[    0.460687] PCI: 0000:00:1f.1 reg 20 io port: [ffa0, ffaf]
[    0.460719] PCI: 0000:00:1f.2 reg 10 io port: [d080, d087]
[    0.460725] PCI: 0000:00:1f.2 reg 14 io port: [d000, d003]
[    0.460729] PCI: 0000:00:1f.2 reg 18 io port: [cc00, cc07]
[    0.460735] PCI: 0000:00:1f.2 reg 1c io port: [c880, c883]
[    0.460740] PCI: 0000:00:1f.2 reg 20 io port: [c800, c80f]
[    0.460758] pci 0000:00:1f.2: PME# supported from D3hot
[    0.460761] pci 0000:00:1f.2: PME# disabled
[    0.460798] PCI: 0000:00:1f.3 reg 20 io port: [400, 41f]
[    0.460857] PCI: bridge 0000:00:1c.0 64bit mmio pref: [fdf00000, fdffffff]
[    0.460900] PCI: 0000:01:00.0 reg 10 io port: [e800, e8ff]
[    0.460913] PCI: 0000:01:00.0 reg 18 32bit mmio: [fdeff000, fdefffff]
[    0.460926] PCI: 0000:01:00.0 reg 20 32bit mmio: [fdee0000, fdeeffff]
[    0.460939] PCI: 0000:01:00.0 reg 30 32bit mmio: [feae0000, feafffff]
[    0.460965] pci 0000:01:00.0: supports D1
[    0.460966] pci 0000:01:00.0: supports D2
[    0.460968] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.460972] pci 0000:01:00.0: PME# disabled
[    0.461002] PCI: bridge 0000:00:1c.1 io port: [e000, efff]
[    0.461005] PCI: bridge 0000:00:1c.1 32bit mmio: [fea00000, feafffff]
[    0.461011] PCI: bridge 0000:00:1c.1 64bit mmio pref: [fde00000, fdefffff]
[    0.461042] PCI: 0000:03:01.0 reg 10 32bit mmio: [febfe000, febfefff]
[    0.461080] pci 0000:03:01.0: PME# supported from D0 D1 D3hot D3cold
[    0.461084] pci 0000:03:01.0: PME# disabled
[    0.461117] PCI: 0000:03:01.3 reg 10 32bit mmio: [febffc00, febffcff]
[    0.461158] pci 0000:03:01.3: PME# supported from D0 D3hot D3cold
[    0.461161] pci 0000:03:01.3: PME# disabled
[    0.461203] pci 0000:00:1e.0: transparent bridge
[    0.461207] PCI: bridge 0000:00:1e.0 32bit mmio: [feb00000, febfffff]
[    0.461224] bus 00 -> node 0
[    0.461230] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.461424] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[    0.461573] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
[    0.461672] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
[    0.464159] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[    0.464256] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[    0.464376] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[    0.464497] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[    0.464617] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[    0.464737] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[    0.464857] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[    0.464976] ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 7 10 11 12 14 15)
[    0.465031] ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - 4F, should be 42 [20080609]
[    0.465031] Linux Plug and Play Support v0.97 (c) Adam Belay
[    0.465031] pnp: PnP ACPI init
[    0.465031] ACPI: bus type pnp registered
[    0.472336] pnp: PnP ACPI: found 16 devices
[    0.472338] ACPI: ACPI bus type pnp unregistered
[    0.472340] PnPBIOS: Disabled by ACPI PNP
[    0.472352] PCI: Using ACPI for IRQ routing
[    0.480037] NET: Registered protocol family 8
[    0.480039] NET: Registered protocol family 20
[    0.480051] NetLabel: Initializing
[    0.480051] NetLabel:  domain hash size = 128
[    0.480051] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.480056] NetLabel:  unlabeled traffic allowed by default
[    0.480148] hpet clockevent registered
[    0.480151] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.480155] hpet0: 3 64-bit timers, 14318180 Hz
[    0.481860] tracer: 772 pages allocated for 65536 entries of 48 bytes
[    0.481863]    actual entries 65620
[    0.481936] AppArmor: AppArmor Filesystem Enabled
[    0.481953] ACPI: RTC can wake from S4
[    0.488045] system 00:01: iomem range 0xfed14000-0xfed19fff has been reserved
[    0.488054] system 00:08: ioport range 0x4d0-0x4d1 has been reserved
[    0.488057] system 00:08: ioport range 0x800-0x87f has been reserved
[    0.488059] system 00:08: ioport range 0x480-0x4bf has been reserved
[    0.488061] system 00:08: ioport range 0x900-0x90f has been reserved
[    0.488064] system 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved
[    0.488066] system 00:08: iomem range 0xfed20000-0xfed8ffff has been reserved
[    0.488071] system 00:0a: iomem range 0xffc00000-0xfff7ffff could not be reserved
[    0.488076] system 00:0b: iomem range 0xfec00000-0xfec00fff has been reserved
[    0.488078] system 00:0b: iomem range 0xfee00000-0xfee00fff could not be reserved
[    0.488083] system 00:0d: ioport range 0x290-0x29f has been reserved
[    0.488089] system 00:0e: iomem range 0xe0000000-0xefffffff has been reserved
[    0.488094] system 00:0f: iomem range 0x0-0x9ffff could not be reserved
[    0.488096] system 00:0f: iomem range 0xc0000-0xcffff could not be reserved
[    0.488098] system 00:0f: iomem range 0xe0000-0xfffff could not be reserved
[    0.488101] system 00:0f: iomem range 0x100000-0xcf6fffff could not be reserved
[    0.523013] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
[    0.523015] pci 0000:00:1c.0:   IO window: disabled
[    0.523019] pci 0000:00:1c.0:   MEM window: disabled
[    0.523022] pci 0000:00:1c.0:   PREFETCH window: 0x000000fdf00000-0x000000fdffffff
[    0.523028] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:01
[    0.523030] pci 0000:00:1c.1:   IO window: 0xe000-0xefff
[    0.523035] pci 0000:00:1c.1:   MEM window: 0xfea00000-0xfeafffff
[    0.523038] pci 0000:00:1c.1:   PREFETCH window: 0x000000fde00000-0x000000fdefffff
[    0.523043] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:03
[    0.523045] pci 0000:00:1e.0:   IO window: disabled
[    0.523049] pci 0000:00:1e.0:   MEM window: 0xfeb00000-0xfebfffff
[    0.523052] pci 0000:00:1e.0:   PREFETCH window: disabled
[    0.523065] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.523069] pci 0000:00:1c.0: setting latency timer to 64
[    0.523076] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[    0.523079] pci 0000:00:1c.1: setting latency timer to 64
[    0.523085] pci 0000:00:1e.0: setting latency timer to 64
[    0.523088] bus: 00 index 0 io port: [0, ffff]
[    0.523089] bus: 00 index 1 mmio: [0, ffffffff]
[    0.523091] bus: 02 index 0 mmio: [0, 0]
[    0.523092] bus: 02 index 1 mmio: [0, 0]
[    0.523094] bus: 02 index 2 mmio: [fdf00000, fdffffff]
[    0.523095] bus: 02 index 3 mmio: [0, 0]
[    0.523097] bus: 01 index 0 io port: [e000, efff]
[    0.523099] bus: 01 index 1 mmio: [fea00000, feafffff]
[    0.523100] bus: 01 index 2 mmio: [fde00000, fdefffff]
[    0.523102] bus: 01 index 3 mmio: [0, 0]
[    0.523103] bus: 03 index 0 mmio: [0, 0]
[    0.523105] bus: 03 index 1 mmio: [feb00000, febfffff]
[    0.523106] bus: 03 index 2 mmio: [0, 0]
[    0.523107] bus: 03 index 3 io port: [0, ffff]
[    0.523109] bus: 03 index 4 mmio: [0, ffffffff]
[    0.523116] NET: Registered protocol family 2
[    0.536073] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.536256] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.536578] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[    0.536769] TCP: Hash tables configured (established 131072 bind 65536)
[    0.536772] TCP reno registered
[    0.544094] NET: Registered protocol family 1
[    0.544184] checking if image is initramfs... it is
[    0.980505] Switched to high resolution mode on CPU 1
[    0.984055] Switched to high resolution mode on CPU 0
[    1.131834] Freeing initrd memory: 8628k freed
[    1.132787] audit: initializing netlink socket (disabled)
[    1.132807] type=2000 audit(1228744299.132:1): initialized
[    1.137679] highmem bounce pool size: 64 pages
[    1.137684] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    1.139489] VFS: Disk quotas dquot_6.5.1
[    1.139556] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.139641] msgmni has been set to 1721
[    1.139740] io scheduler noop registered
[    1.139743] io scheduler anticipatory registered
[    1.139745] io scheduler deadline registered
[    1.139754] io scheduler cfq registered (default)
[    1.139766] pci 0000:00:02.0: Boot video device
[    1.139951] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[    1.139982] pcieport-driver 0000:00:1c.0: found MSI capability
[    1.140014] pci_express 0000:00:1c.0:pcie00: allocate port service
[    1.140047] pci_express 0000:00:1c.0:pcie02: allocate port service
[    1.140078] pci_express 0000:00:1c.0:pcie03: allocate port service
[    1.140156] pcieport-driver 0000:00:1c.1: setting latency timer to 64
[    1.140185] pcieport-driver 0000:00:1c.1: found MSI capability
[    1.140214] pci_express 0000:00:1c.1:pcie00: allocate port service
[    1.140247] pci_express 0000:00:1c.1:pcie02: allocate port service
[    1.140278] pci_express 0000:00:1c.1:pcie03: allocate port service
[    1.140531] isapnp: Scanning for PnP cards...
[    1.494122] isapnp: No Plug & Play device found
[    1.519065] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[    1.519174] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.519746] 00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.521100] brd: module loaded
[    1.521154] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[    1.521302] PNP: No PS/2 controller found. Probing ports directly.
[    1.523553] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.523558] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.523781] mice: PS/2 mouse device common for all mice
[    1.523877] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[    1.523897] rtc0: alarms up to one month, y3k, hpet irqs
[    1.523992] EISA: Probing bus 0 at eisa.0
[    1.524016] EISA: Detected 0 cards.
[    1.524019] cpuidle: using governor ladder
[    1.524021] cpuidle: using governor menu
[    1.524419] TCP cubic registered
[    1.524442] Using IPI No-Shortcut mode
[    1.524582] registered taskstats version 1
[    1.524673]   Magic number: 4:355:887
[    1.524708] tty ptyue: hash matches
[    1.524727] pci 0000:00:1f.0: hash matches
[    1.524756] rtc_cmos 00:03: setting system clock to 2008-12-08 13:51:40 UTC (1228744300)
[    1.524759] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    1.524761] EDD information not available.
[    1.524952] Freeing unused kernel memory: 424k freed
[    1.524982] Write protecting the kernel text: 2576k
[    1.525002] Write protecting the kernel read-only data: 936k
[    1.672127] fuse init (API version 7.9)
[    1.728407] ACPI: SSDT CF6C20F0, 0277 (r1 DpgPmm  P001Ist       11 INTL 20051117)
[    1.728728] processor ACPI0007:00: registered as cooling_device0
[    1.729032] ACPI: SSDT CF6C2580, 0277 (r1 DpgPmm  P002Ist       12 INTL 20051117)
[    1.729335] processor ACPI0007:01: registered as cooling_device1
[    1.772627] md: linear personality registered for level -1
[    1.775575] md: multipath personality registered for level -4
[    1.784120] md: raid0 personality registered for level 0
[    1.788234] md: raid1 personality registered for level 1
[    1.790580] xor: automatically using best checksumming function: pIII_sse
[    1.808501]    pIII_sse  :  9233.000 MB/sec
[    1.808502] xor: using function: pIII_sse (9233.000 MB/sec)
[    1.809556] async_tx: api initialized (async)
[    1.880568] raid6: int32x1    918 MB/s
[    1.948500] raid6: int32x2    947 MB/s
[    2.016549] raid6: int32x4    736 MB/s
[    2.084523] raid6: int32x8    683 MB/s
[    2.152503] raid6: mmxx1     3112 MB/s
[    2.220504] raid6: mmxx2     3546 MB/s
[    2.288521] raid6: sse1x1    2095 MB/s
[    2.356507] raid6: sse1x2    2670 MB/s
[    2.424514] raid6: sse2x1    3785 MB/s
[    2.492514] raid6: sse2x2    4041 MB/s
[    2.492516] raid6: using algorithm sse2x2 (4041 MB/s)
[    2.492519] md: raid6 personality registered for level 6
[    2.492520] md: raid5 personality registered for level 5
[    2.492522] md: raid4 personality registered for level 4
[    2.510594] md: raid10 personality registered for level 10
[    2.703514] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    2.703531] r8169 0000:01:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    2.703547] r8169 0000:01:00.0: setting latency timer to 64
[    2.703558] r8169 0000:01:00.0: unknown MAC (27a00000)
[    2.703829] eth0: RTL8169 at 0xf8896000, 00:19:66:95:4c:ba, XID 24a00000 IRQ 221
[    2.729765] usbcore: registered new interface driver usbfs
[    2.729786] usbcore: registered new interface driver hub
[    2.729814] usbcore: registered new device driver usb
[    2.736170] USB Universal Host Controller Interface driver v3.0
[    2.736214] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    2.736222] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    2.736225] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    2.736259] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[    2.736286] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000d400
[    2.736405] usb usb1: configuration #1 chosen from 1 choice
[    2.736426] hub 1-0:1.0: USB hub found
[    2.736432] hub 1-0:1.0: 2 ports detected
[    2.752830] No dock devices found.
[    2.776300] SCSI subsystem initialized
[    2.789676] libata version 3.00 loaded.
[    2.796095] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.944235] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    2.944245] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    2.944249] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    2.944269] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[    2.944299] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000d480
[    2.944375] usb usb2: configuration #1 chosen from 1 choice
[    2.944397] hub 2-0:1.0: USB hub found
[    2.944403] hub 2-0:1.0: 2 ports detected
[    3.052010] usb 1-1: new low speed USB device using uhci_hcd and address 2
[    3.148196] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    3.148205] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    3.148208] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    3.148231] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[    3.148259] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000d800
[    3.148331] usb usb3: configuration #1 chosen from 1 choice
[    3.148354] hub 3-0:1.0: USB hub found
[    3.148360] hub 3-0:1.0: 2 ports detected
[    3.228465] usb 1-1: configuration #1 chosen from 1 choice
[    3.252113] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[    3.252118] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[    3.252121] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    3.252139] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[    3.252164] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000d880
[    3.252228] usb usb4: configuration #1 chosen from 1 choice
[    3.252248] hub 4-0:1.0: USB hub found
[    3.252253] hub 4-0:1.0: 2 ports detected
[    3.340009] usb 1-2: new low speed USB device using uhci_hcd and address 3
[    3.460167] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    3.460179] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[    3.460182] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    3.460205] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
[    3.464093] ehci_hcd 0000:00:1d.7: debug port 1
[    3.464098] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[    3.464102] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfe977c00
[    3.476016] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[    3.476144] usb usb5: configuration #1 chosen from 1 choice
[    3.476169] hub 5-0:1.0: USB hub found
[    3.476176] hub 5-0:1.0: 8 ports detected
[    3.488319] usb 1-2: device descriptor read/all, error -71
[    3.544038] hub 1-0:1.0: unable to enumerate USB device on port 2
[    3.672023] usb 1-1: USB disconnect, address 2
[    3.684143] ata_piix 0000:00:1f.1: version 2.12
[    3.684155] ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    3.684189] ata_piix 0000:00:1f.1: setting latency timer to 64
[    3.684247] scsi0 : ata_piix
[    3.684320] scsi1 : ata_piix
[    3.685377] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[    3.685380] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[    4.014694] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    4.014698] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
[    4.014724] ata_piix 0000:00:1f.2: setting latency timer to 64
[    4.014929] scsi2 : ata_piix
[    4.015181] scsi3 : ata_piix
[    4.016765] ata3: SATA max UDMA/133 cmd 0xd080 ctl 0xd000 bmdma 0xc800 irq 19
[    4.016767] ata4: SATA max UDMA/133 cmd 0xcc00 ctl 0xc880 bmdma 0xc808 irq 19
[    4.024509] usb 5-3: new high speed USB device using ehci_hcd and address 4
[    4.157083] usb 5-3: configuration #1 chosen from 1 choice
[    4.157726] usbcore: registered new interface driver hiddev
[    4.188283] ata3.00: ATA-7: SAMSUNG HD252HJ, 1AC01113, max UDMA7
[    4.188286] ata3.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    4.188301] ata3.01: ATAPI: TSSTcorp CDDVDW SH-S223F, SB01, max UDMA/100
[    4.196284] ata3.00: configured for UDMA/133
[    4.212185] ata3.01: configured for UDMA/100
[    4.384273] ata4.00: ATA-7: SAMSUNG HD252HJ, 1AC01113, max UDMA7
[    4.384276] ata4.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    4.396008] usb 1-1: new low speed USB device using uhci_hcd and address 5
[    4.431705] ata4.01: ATA-7: ST3500630NS, 3.AEE, max UDMA/133
[    4.431707] ata4.01: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    4.452282] ata4.00: configured for UDMA/133
[    4.498349] ata4.01: configured for UDMA/133
[    4.498432] scsi 2:0:0:0: Direct-Access     ATA      SAMSUNG HD252HJ  1AC0 PQ: 0 ANSI: 5
[    4.499199] scsi 2:0:1:0: CD-ROM            TSSTcorp CDDVDW SH-S223F  SB01 PQ: 0 ANSI: 5
[    4.499338] scsi 3:0:0:0: Direct-Access     ATA      SAMSUNG HD252HJ  1AC0 PQ: 0 ANSI: 5
[    4.499435] scsi 3:0:1:0: Direct-Access     ATA      ST3500630NS      3.AE PQ: 0 ANSI: 5
[    4.499504] ehci_hcd 0000:03:01.3: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[    4.499517] ehci_hcd 0000:03:01.3: EHCI Host Controller
[    4.499540] ehci_hcd 0000:03:01.3: new USB bus registered, assigned bus number 6
[    4.520014] ehci_hcd 0000:03:01.3: debug port 1
[    4.520026] ehci_hcd 0000:03:01.3: irq 22, io mem 0xfebffc00
[    4.532006] ehci_hcd 0000:03:01.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[    4.532091] usb usb6: configuration #1 chosen from 1 choice
[    4.532113] hub 6-0:1.0: USB hub found
[    4.532119] hub 6-0:1.0: 6 ports detected
[    4.572508] usb 1-1: configuration #1 chosen from 1 choice
[    4.636116] ohci_hcd 0000:03:01.0: PCI INT B -> GSI 23 (level, low) -> IRQ 23
[    4.636124] ohci_hcd 0000:03:01.0: OHCI Host Controller
[    4.636143] ohci_hcd 0000:03:01.0: new USB bus registered, assigned bus number 7
[    4.636153] ohci_hcd 0000:03:01.0: irq 23, io mem 0xfebfe000
[    4.694111] usb usb7: configuration #1 chosen from 1 choice
[    4.694137] hub 7-0:1.0: USB hub found
[    4.694145] hub 7-0:1.0: 2 ports detected
[    4.810850] scsi 2:0:0:0: Attached scsi generic sg0 type 0
[    4.810883] scsi 2:0:1:0: Attached scsi generic sg1 type 5
[    4.810911] scsi 3:0:0:0: Attached scsi generic sg2 type 0
[    4.810939] scsi 3:0:1:0: Attached scsi generic sg3 type 0
[    4.816031] usb 1-2: new low speed USB device using uhci_hcd and address 6
[    4.829503] Driver 'sd' needs updating - please use bus_type methods
[    4.829596] sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
[    4.829612] sd 2:0:0:0: [sda] Write Protect is off
[    4.829614] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    4.829639] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.829698] sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
[    4.829711] sd 2:0:0:0: [sda] Write Protect is off
[    4.829713] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    4.829738] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.829741]  sda:<4>Driver 'sr' needs updating - please use bus_type methods
[    4.840476]  sda1 sda2 sda3 < sda5 >
[    4.846475] sd 2:0:0:0: [sda] Attached SCSI disk
[    4.846590] sd 3:0:0:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
[    4.846605] sd 3:0:0:0: [sdb] Write Protect is off
[    4.846607] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    4.846633] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.846679] sd 3:0:0:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
[    4.846693] sd 3:0:0:0: [sdb] Write Protect is off
[    4.846695] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    4.846719] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.846722]  sdb: sdb1 sdb2 sdb3 <sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[    4.850173] Uniform CD-ROM driver Revision: 3.20
[    4.850236] sr 2:0:1:0: Attached scsi CD-ROM sr0
[    4.857361]  sdb5 >
[    4.857472] sd 3:0:0:0: [sdb] Attached SCSI disk
[    4.857534] sd 3:0:1:0: [sdc] 976773168 512-byte hardware sectors (500108 MB)
[    4.857549] sd 3:0:1:0: [sdc] Write Protect is off
[    4.857551] sd 3:0:1:0: [sdc] Mode Sense: 00 3a 00 00
[    4.857576] sd 3:0:1:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.857622] sd 3:0:1:0: [sdc] 976773168 512-byte hardware sectors (500108 MB)
[    4.857636] sd 3:0:1:0: [sdc] Write Protect is off
[    4.857638] sd 3:0:1:0: [sdc] Mode Sense: 00 3a 00 00
[    4.857663] sd 3:0:1:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.857665]  sdc: sdc1
[    4.871266] sd 3:0:1:0: [sdc] Attached SCSI disk
[    4.983046] usb 1-2: configuration #1 chosen from 1 choice
[    5.000599] input: CHESEN USB Keyboard as /devices/pci0000:00/0000:00:1d.0/usb1/1-1/1-1:1.0/input/input1
[    5.012340] input,hidraw0: USB HID v1.10 Keyboard [CHESEN USB Keyboard] on usb-0000:00:1d.0-1
[    5.021600] md: md0 stopped.
[    5.039384] input: CHESEN USB Keyboard as /devices/pci0000:00/0000:00:1d.0/usb1/1-1/1-1:1.1/input/input2
[    5.040581] input,hidraw1: USB HID v1.10 Device [CHESEN USB Keyboard] on usb-0000:00:1d.0-1
[    5.053508] input: USB Mouse as /devices/pci0000:00/0000:00:1d.0/usb1/1-2/1-2:1.0/input/input3
[    5.056408] input,hidraw2: USB HID v1.10 Mouse [USB Mouse] on usb-0000:00:1d.0-2
[    5.056437] usbcore: registered new interface driver libusual
[    5.056662] usbcore: registered new interface driver usbhid
[    5.056664] usbhid: v2.6:USB HID core driver
[    5.071015] Initializing USB Mass Storage driver...
[    5.071317] scsi4 : SCSI emulation for USB Mass Storage devices
[    5.072171] usb-storage: device found at 4
[    5.072173] usb-storage: waiting for device to settle before scanning
[    5.072200] usbcore: registered new interface driver usb-storage
[    5.072203] USB Mass Storage support registered.
[    5.127067] md: bind<sda1>
[    5.127200] md: md1 stopped.
[    5.133350] md: bind<sda2>
[    5.133466] md: md2 stopped.
[    5.141757] md: bind<sda5>
[    5.154912] md: md0 stopped.
[    5.154924] md: unbind<sda1>
[    5.156640] md: export_rdev(sda1)
[    5.176247] md: bind<sdb1>
[    5.176390] md: bind<sda1>
[    5.183008] raid1: raid set md0 active with 2 out of 2 mirrors
[    5.183066] md: md1 stopped.
[    5.183074] md: unbind<sda2>
[    5.188522] md: export_rdev(sda2)
[    5.215321] md: bind<sdb2>
[    5.215469] md: bind<sda2>
[    5.222076] raid1: raid set md1 active with 2 out of 2 mirrors
[    5.222136] md: md2 stopped.
[    5.222143] md: unbind<sda5>
[    5.228524] md: export_rdev(sda5)
[    5.340488] md: bind<sdb5>
[    5.340638] md: bind<sda5>
[    5.347128] raid1: raid set md2 active with 2 out of 2 mirrors
[    5.467123] PM: Starting manual resume from disk
[    5.467126] PM: Resume from partition 9:1
[    5.467127] PM: Checking hibernation image.
[    5.467261] PM: Resume from disk failed.
[    5.538045] kjournald starting.  Commit interval 5 seconds
[    5.538050] EXT3-fs: mounted filesystem with ordered data mode.
[   10.072712] usb-storage: device scan complete
[   10.073080] scsi 4:0:0:0: Direct-Access     WDC      WD1600BB-00DWA0  15.0 PQ: 0 ANSI: 2
[   10.073939] sd 4:0:0:0: [sdd] 312581808 512-byte hardware sectors (160042 MB)
[   10.074688] sd 4:0:0:0: [sdd] Write Protect is off
[   10.074691] sd 4:0:0:0: [sdd] Mode Sense: 53 00 00 08
[   10.074693] sd 4:0:0:0: [sdd] Assuming drive cache: write through
[   10.075310] sd 4:0:0:0: [sdd] 312581808 512-byte hardware sectors (160042 MB)
[   10.076062] sd 4:0:0:0: [sdd] Write Protect is off
[   10.076064] sd 4:0:0:0: [sdd] Mode Sense: 53 00 00 08
[   10.076066] sd 4:0:0:0: [sdd] Assuming drive cache: write through
[   10.076069]  sdd: sdd1
[   10.091177] sd 4:0:0:0: [sdd] Attached SCSI disk
[   10.091269] sd 4:0:0:0: Attached scsi generic sg4 type 0
[   10.158795] udevd version 124 started
[   10.454370] Linux agpgart interface v0.103
[   10.539799] iTCO_vendor_support: vendor-support=0
[   10.565174] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[   10.565565] iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0860)
[   10.565644] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   10.583795] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   10.616471] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   10.630414] agpgart-intel 0000:00:00.0: Intel G33 Chipset
[   10.630931] agpgart-intel 0000:00:00.0: detected 7164K stolen memory
[   10.650971] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
[   10.651779] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[   10.663643] intel_rng: FWH not detected
[   10.668534] ACPI: Power Button (FF) [PWRF]
[   10.668630] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input5
[   10.700541] ACPI: Power Button (CM) [PWRB]
[   10.922943] parport_pc 00:07: reported by Plug and Play ACPI
[   10.923016] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[   11.112310] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   11.112327] HDA Intel 0000:00:1b.0: setting latency timer to 64
[   11.145898] hda_codec: Unknown model for ALC662, trying auto-probe from BIOS...
[   11.368482] input: PC Speaker as /devices/platform/pcspkr/input/input6
[   13.147652] loop: module loaded
[   13.165689] lp0: using parport0 (interrupt-driven).
[   13.258797] Adding 4883640k swap on /dev/md1.  Priority:-1 extents:1 across:4883640k
[   13.829205] EXT3 FS on md2, internal journal
[   14.021523] device-mapper: uevent: version 1.0.3
[   14.021657] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[   14.817091] kjournald starting.  Commit interval 5 seconds
[   14.836993] EXT3 FS on md0, internal journal
[   14.836997] EXT3-fs: mounted filesystem with ordered data mode.
[   15.121734] type=1505 audit(1228744314.068:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=4357
[   15.248584] type=1505 audit(1228744314.196:3): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=4362
[   15.248741] type=1505 audit(1228744314.196:4): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=4362
[   15.409175] ip_tables: (C) 2000-2006 Netfilter Core Team
[   15.833465] ACPI: WMI: Mapper loaded
[   16.679944] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
[   16.851852] NET: Registered protocol family 10
[   16.852259] lo: Disabled Privacy Extensions
[   16.938114] apm: BIOS version 1.2 Flags 0x02 (Driver version 1.16ac)
[   16.938120] apm: disabled - APM is not SMP safe.
[   18.429369] Bluetooth: Core ver 2.13
[   18.430192] NET: Registered protocol family 31
[   18.430200] Bluetooth: HCI device and connection manager initialized
[   18.430205] Bluetooth: HCI socket layer initialized
[   18.498140] Bluetooth: L2CAP ver 2.11
[   18.498150] Bluetooth: L2CAP socket layer initialized
[   18.518910] Bluetooth: SCO (Voice Link) ver 0.6
[   18.518920] Bluetooth: SCO socket layer initialized
[   18.548658] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   18.548666] Bluetooth: BNEP filters: protocol multicast
[   18.583355] Bridge firewalling registered
[   18.584607] pan0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
[   18.657807] Bluetooth: RFCOMM socket layer initialized
[   18.657825] Bluetooth: RFCOMM TTY layer initialized
[   18.657829] Bluetooth: RFCOMM ver 1.10
[   21.309070] [drm] Initialized drm 1.1.0 20060810
[   21.333646] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   21.333653] pci 0000:00:02.0: setting latency timer to 64
[   21.334239] [drm] Initialized i915 1.6.0 20060119 on minor 0
[   21.756971] set status page addr 0x00033000
[   22.788641] r8169: eth0: link up
[   22.788653] r8169: eth0: link up
[   22.916213] NET: Registered protocol family 17
[   33.460015] eth0: no IPv6 routers present