[ 0.000000] Linux version 2.6.22-14-generic (buildd@palmer) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Tue Oct 9 09:51:52 GMT 2007 (Ubuntu 2.6.22-14.41-generic) [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 00000000000a0000 (usable) [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 0000000013ff0000 (usable) [ 0.000000] BIOS-e820: 0000000013ff0000 - 0000000013ff3000 (ACPI NVS) [ 0.000000] BIOS-e820: 0000000013ff3000 - 0000000014000000 (ACPI data) [ 0.000000] BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) [ 0.000000] 0MB HIGHMEM available. [ 0.000000] 319MB LOWMEM available. [ 0.000000] Entering add_active_range(0, 0, 81904) 0 entries of 256 used [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] Normal 4096 -> 81904 [ 0.000000] HighMem 81904 -> 81904 [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0 -> 81904 [ 0.000000] On node 0 totalpages: 81904 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 [ 0.000000] Normal zone: 607 pages used for memmap [ 0.000000] Normal zone: 77201 pages, LIFO batch:15 [ 0.000000] HighMem zone: 0 pages used for memmap [ 0.000000] DMI 2.3 present. [ 0.000000] ACPI: RSDP signature @ 0xC00F7B40 checksum 0 [ 0.000000] ACPI: RSDP 000F7B40, 0014 (r0 BIOSTA) [ 0.000000] ACPI: RSDT 13FF3000, 0028 (r1 BIOSTA AWRDACPI 42302E31 AWRD 0) [ 0.000000] ACPI: FACP 13FF3040, 0074 (r1 BIOSTA AWRDACPI 42302E31 AWRD 0) [ 0.000000] ACPI: DSDT 13FF30C0, 25A7 (r1 VIA694 AWRDACPI 1000 MSFT 100000C) [ 0.000000] ACPI: FACS 13FF0000, 0040 [ 0.000000] ACPI: PM-Timer IO Port: 0x4008 [ 0.000000] Allocating PCI resources starting at 20000000 (gap: 14000000:ebff0000) [ 0.000000] Built 1 zonelists. Total pages: 81265 [ 0.000000] Kernel command line: root=UUID=6e82d5ce-a452-4a1c-ae79-bd836b592561 ro quiet splash apic=noirq lapic [ 0.000000] Local APIC disabled by BIOS -- reenabling. [ 0.000000] Found and enabled local APIC! [ 0.000000] mapped APIC to ffffd000 (fee00000) [ 0.000000] Enabling fast FPU save and restore... done. [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes) [ 0.000000] Detected 1195.996 MHz processor. [ 22.327307] Console: colour VGA+ 80x25 [ 22.328360] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 22.329024] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 22.351447] Memory: 313100k/327616k available (2015k kernel code, 13888k reserved, 916k data, 364k init, 0k highmem) [ 22.351467] virtual kernel memory layout: [ 22.351469] fixmap : 0xfff4d000 - 0xfffff000 ( 712 kB) [ 22.351472] pkmap : 0xff800000 - 0xffc00000 (4096 kB) [ 22.351474] vmalloc : 0xd4800000 - 0xff7fe000 ( 687 MB) [ 22.351476] lowmem : 0xc0000000 - 0xd3ff0000 ( 319 MB) [ 22.351479] .init : 0xc03e3000 - 0xc043e000 ( 364 kB) [ 22.351481] .data : 0xc02f7d26 - 0xc03dce84 ( 916 kB) [ 22.351483] .text : 0xc0100000 - 0xc02f7d26 (2015 kB) [ 22.351490] Checking if this processor honours the WP bit even in supervisor mode... Ok. [ 22.351575] SLUB: Genslabs=22, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1 [ 22.431590] Calibrating delay using timer specific routine.. 2394.47 BogoMIPS (lpj=4788955) [ 22.431649] Security Framework v1.0.0 initialized [ 22.431662] SELinux: Disabled at boot. [ 22.431699] Mount-cache hash table entries: 512 [ 22.431965] CPU: After generic identify, caps: 0183fbff c1c7fbff 00000000 00000000 00000000 00000000 00000000 [ 22.431982] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 22.431987] CPU: L2 Cache: 256K (64 bytes/line) [ 22.431993] CPU: After all inits, caps: 0183fbff c1c7fbff 00000000 00000420 00000000 00000000 00000000 [ 22.432013] Compat vDSO mapped to ffffe000. [ 22.432038] Checking 'hlt' instruction... OK. [ 22.447652] SMP alternatives: switching to UP code [ 22.448134] Freeing SMP alternatives: 11k freed [ 22.448850] Early unpacking initramfs... done [ 23.021598] ACPI: Core revision 20070126 [ 23.021791] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found. [ 23.023334] ACPI: setting ELCR to 0800 (from 1e00) [ 23.099587] CPU0: AMD Athlon(tm) Processor stepping 02 [ 23.099599] SMP motherboard not detected. [ 23.207558] Brought up 1 CPUs [ 23.207881] Booting paravirtualized kernel on bare hardware [ 23.208005] Time: 12:52:16 Date: 09/11/107 [ 23.208076] NET: Registered protocol family 16 [ 23.208300] EISA bus registered [ 23.208323] ACPI: bus type pci registered [ 23.241335] PCI: PCI BIOS revision 2.10 entry at 0xfb170, last bus=1 [ 23.241340] PCI: Using configuration type 1 [ 23.241343] Setting up standard PCI resources [ 23.251703] ACPI: EC: Look up EC in DSDT [ 23.255245] ACPI: Interpreter enabled [ 23.255251] ACPI: (supports S0 S1 S4 S5) [ 23.255278] ACPI: Using PIC for interrupt routing [ 23.260621] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 23.260643] PCI: Probing PCI hardware (bus 00) [ 23.260796] Disabling VIA memory write queue (PCI ID 0305, rev 03): [55] 81 & 1f -> 01 [ 23.260973] PCI quirk: region 4000-40ff claimed by vt82c586 ACPI [ 23.260979] PCI quirk: region 6000-607f claimed by vt82c686 HW-mon [ 23.260984] PCI quirk: region 5000-500f claimed by vt82c686 SMB [ 23.261479] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 23.280690] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 11 12 14 15) [ 23.280888] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 *11 12 14 15) [ 23.281084] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *9 [ 23.281278] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 11 *12 14 15) [ 23.281409] Linux Plug and Play Support v0.97 (c) Adam Belay [ 23.281432] pnp: PnP ACPI init [ 23.281451] ACPI: bus type pnp registered [ 23.284998] pnp: PnP ACPI: found 11 devices [ 23.285003] ACPI: ACPI bus type pnp unregistered [ 23.285011] PnPBIOS: Disabled by ACPI PNP [ 23.285131] PCI: Using ACPI for IRQ routing [ 23.285138] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 23.313999] NET: Registered protocol family 8 [ 23.314003] NET: Registered protocol family 20 [ 23.314187] pnp: 00:00: iomem range 0xcb800-0xcbfff has been reserved [ 23.314193] pnp: 00:00: iomem range 0xf0000-0xf7fff could not be reserved [ 23.314198] pnp: 00:00: iomem range 0xf8000-0xfbfff could not be reserved [ 23.314203] pnp: 00:00: iomem range 0xfc000-0xfffff could not be reserved [ 23.315442] Time: tsc clocksource has been installed. [ 23.344768] PCI: Bridge: 0000:00:01.0 [ 23.344772] IO window: disabled. [ 23.344780] MEM window: e0000000-e1ffffff [ 23.344785] PREFETCH window: d8000000-dfffffff [ 23.344809] PCI: Setting latency timer of device 0000:00:01.0 to 64 [ 23.344832] NET: Registered protocol family 2 [ 23.383578] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) [ 23.383711] TCP established hash table entries: 16384 (order: 5, 196608 bytes) [ 23.384475] TCP bind hash table entries: 16384 (order: 5, 131072 bytes) [ 23.385169] TCP: Hash tables configured (established 16384 bind 16384) [ 23.385175] TCP reno registered [ 23.395799] checking if image is initramfs...<6>Switched to high resolution mode on CPU 0 [ 23.860800] it is [ 24.463621] Freeing initrd memory: 7050k freed [ 24.464549] audit: initializing netlink socket (disabled) [ 24.464585] audit(1192107136.792:1): initialized [ 24.468014] VFS: Disk quotas dquot_6.5.1 [ 24.468124] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 24.468345] io scheduler noop registered [ 24.468349] io scheduler anticipatory registered [ 24.468353] io scheduler deadline registered [ 24.468376] io scheduler cfq registered (default) [ 24.468415] PCI: VIA PCI bridge detected. Disabling DAC. [ 24.468421] PCI: Disabling Via external APIC routing [ 24.468484] Boot video device is 0000:01:00.0 [ 24.468837] isapnp: Scanning for PnP cards... [ 24.823266] isapnp: No Plug & Play device found [ 24.883672] Real Time Clock Driver v1.12ac [ 24.883851] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [ 24.884012] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 24.884412] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 24.885670] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 24.886248] 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 24.887933] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize [ 24.888443] input: Macintosh mouse button emulation as /class/input/input0 [ 24.888688] PNP: No PS/2 controller found. Probing ports directly. [ 24.889132] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 24.889142] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 24.889465] mice: PS/2 mouse device common for all mice [ 24.889707] EISA: Probing bus 0 at eisa.0 [ 24.889743] Cannot allocate resource for EISA slot 4 [ 24.889747] Cannot allocate resource for EISA slot 5 [ 24.889751] Cannot allocate resource for EISA slot 6 [ 24.889765] EISA: Detected 0 cards. [ 24.890195] TCP cubic registered [ 24.890214] NET: Registered protocol family 1 [ 24.890320] Testing NMI watchdog ... OK. [ 24.969990] Using IPI No-Shortcut mode [ 24.970420] Magic number: 11:461:885 [ 24.970654] hash matches device ptyx9 [ 24.970680] hash matches device ptyuc [ 24.971915] Freeing unused kernel memory: 364k freed [ 26.359222] AppArmor: AppArmor initialized<5>audit(1192107138.792:2): type=1505 info="AppArmor initialized" pid=1164 [ 26.375211] fuse init (API version 7.8) [ 26.384651] Failure registering capabilities with primary security module. [ 26.408881] ACPI: CPU0 (power states: C1[C1] C2[C2]) [ 26.408894] ACPI: Processor [CPU0] (supports 2 throttling states) [ 27.495719] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 [ 27.495734] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 27.497055] VP_IDE: IDE controller at PCI slot 0000:00:07.1 [ 27.497092] VP_IDE: chipset revision 16 [ 27.497096] VP_IDE: not 100% native mode: will probe irqs later [ 27.497118] VP_IDE: VIA vt82c686a (rev 22) IDE UDMA66 controller on pci0000:00:07.1 [ 27.497131] ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:pio [ 27.497152] ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:DMA, hdd:DMA [ 27.497164] Probing IDE interface ide0... [ 27.566820] 8139too Fast Ethernet driver 0.9.28 [ 27.586703] usbcore: registered new interface driver usbfs [ 27.586761] usbcore: registered new interface driver hub [ 27.586820] usbcore: registered new device driver usb [ 27.588602] USB Universal Host Controller Interface driver v3.0 [ 27.838125] Floppy drive(s): fd0 is 1.44M [ 27.896166] FDC 0 is a post-1991 82077 [ 27.942242] hda: WDC AC310200R, ATA DISK drive [ 5.460000] Marking TSC unstable due to: possible TSC halt in C2. [ 5.476000] Time: acpi_pm clocksource has been installed. [ 6.104000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 [ 6.104000] Probing IDE interface ide1... [ 6.968000] hdc: ATAPI CDROM, ATAPI CD/DVD-ROM drive [ 7.752000] hdd: 4X4X32, ATAPI CD/DVD-ROM drive [ 7.808000] ide1 at 0x170-0x177,0x376 on irq 15 [ 7.824000] SCSI subsystem initialized [ 7.832000] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11 [ 7.832000] PCI: setting IRQ 11 as level-triggered [ 7.832000] ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11 [ 7.832000] eth0: RealTek RTL8139 at 0xd486a000, 00:50:22:83:df:ae, IRQ 11 [ 7.832000] eth0: Identified 8139 chip type 'RTL-8139C' [ 7.832000] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10 [ 7.832000] PCI: setting IRQ 10 as level-triggered [ 7.832000] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10 [ 7.832000] uhci_hcd 0000:00:0a.0: UHCI Host Controller [ 7.836000] uhci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1 [ 7.836000] uhci_hcd 0000:00:0a.0: irq 10, io base 0x0000e000 [ 7.836000] usb usb1: configuration #1 chosen from 1 choice [ 7.836000] hub 1-0:1.0: USB hub found [ 7.836000] hub 1-0:1.0: 2 ports detected [ 7.836000] libata version 2.21 loaded. [ 7.844000] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004) [ 7.940000] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 12 [ 7.940000] PCI: setting IRQ 12 as level-triggered [ 7.940000] ACPI: PCI Interrupt 0000:00:0a.1[B] -> Link [LNKD] -> GSI 12 (level, low) -> IRQ 12 [ 7.940000] uhci_hcd 0000:00:0a.1: UHCI Host Controller [ 7.940000] uhci_hcd 0000:00:0a.1: new USB bus registered, assigned bus number 2 [ 7.940000] uhci_hcd 0000:00:0a.1: irq 12, io base 0x0000e400 [ 7.940000] usb usb2: configuration #1 chosen from 1 choice [ 7.940000] hub 2-0:1.0: USB hub found [ 7.940000] hub 2-0:1.0: 2 ports detected [ 8.044000] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10 [ 8.044000] ACPI: PCI Interrupt 0000:00:0a.2[C] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10 [ 8.044000] ehci_hcd 0000:00:0a.2: EHCI Host Controller [ 8.044000] ehci_hcd 0000:00:0a.2: new USB bus registered, assigned bus number 3 [ 8.044000] ehci_hcd 0000:00:0a.2: irq 10, io mem 0xe3001000 [ 8.044000] ehci_hcd 0000:00:0a.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 8.044000] usb usb3: configuration #1 chosen from 1 choice [ 8.044000] hub 3-0:1.0: USB hub found [ 8.044000] hub 3-0:1.0: 4 ports detected [ 8.160000] hda: max request size: 128KiB [ 8.160000] hda: 20044080 sectors (10262 MB) w/512KiB Cache, CHS=19885/16/63<4>hda: drive side 80-wire cable detection failed, limiting max speed to UDMA33 [ 8.160000] [ 8.160000] hda: cache flushes not supported [ 8.160000] hda: hda1 hda2 < hda5 > [ 8.236000] hdc: ATAPI 40X CD-ROM drive, 128kB Cache, UDMA(33) [ 8.236000] Uniform CD-ROM driver Revision: 3.20 [ 8.240000] hdd: ATAPI 32X CD-ROM CD-R/RW drive, 2048kB Cache, DMA [ 8.572000] Attempting manual resume [ 8.572000] swsusp: Resume From Partition 3:5 [ 8.572000] PM: Checking swsusp image. [ 8.588000] PM: Resume from disk failed. [ 8.656000] kjournald starting. Commit interval 5 seconds [ 8.656000] EXT3-fs: mounted filesystem with ordered data mode. [ 10.800000] spurious 8259A interrupt: IRQ7. [ 30.404000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 30.420000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 30.776000] Linux agpgart interface v0.102 (c) Dave Jones [ 30.932000] agpgart: Detected VIA Twister-K/KT133x/KM133 chipset [ 30.944000] agpgart: AGP aperture is 128M @ 0xd0000000 [ 30.988000] parport_pc: VIA 686A/8231 detected [ 30.988000] parport_pc: probing current configuration [ 30.988000] parport_pc: Current parallel port base: 0x378 [ 30.988000] parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP] [ 31.084000] parport_pc: VIA parallel port: io=0x378, irq=7 [ 31.548000] Linux video capture interface: v2.00 [ 31.668000] bttv: driver version 0.9.17 loaded [ 31.668000] bttv: using 8 buffers with 2080k (520 pages) each for capture [ 31.668000] bttv: Bt8xx card found (0). [ 31.668000] ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKD] -> GSI 12 (level, low) -> IRQ 12 [ 31.668000] bttv0: Bt878 (rev 17) at 0000:00:0b.0, irq: 12, latency: 32, mmio: 0xe3002000 [ 31.668000] bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb [ 31.668000] bttv0: using: Hauppauge (bt878) [card=10,autodetected] [ 31.668000] bttv0: gpio: en=00000000, out=00000000 in=00ffffdb [init] [ 31.668000] bttv0: Hauppauge/Voodoo msp34xx: reset line init [5] [ 31.696000] tveeprom 1-0050: Hauppauge model 44354, rev A321, serial# 5112497 [ 31.696000] tveeprom 1-0050: tuner model is Philips FM1216 (idx 21, type 5) [ 31.696000] tveeprom 1-0050: TV standards PAL(B/G) (eeprom 0x04) [ 31.696000] tveeprom 1-0050: audio processor is MSP3415 (idx 6) [ 31.696000] tveeprom 1-0050: has radio [ 31.696000] bttv0: Hauppauge eeprom indicates model#44354 [ 31.696000] bttv0: using tuner=5 [ 31.696000] bttv0: i2c: checking for MSP34xx @ 0x80... found [ 32.072000] msp3400 1-0040: MSP3415D-B3 found @ 0x80 (bt878 #0 [sw]) [ 32.072000] msp3400 1-0040: MSP3415D-B3 supports nicam, mode is autodetect [ 32.404000] nvidia: module license 'NVIDIA' taints kernel. [ 32.772000] input: PC Speaker as /class/input/input1 [ 33.264000] bttv0: i2c: checking for TDA9875 @ 0xb0... not found [ 33.320000] bttv0: i2c: checking for TDA7432 @ 0x8a... not found [ 33.648000] bttv0: i2c: checking for TDA9887 @ 0x86... not found [ 33.704000] tuner 1-0061: chip found @ 0xc2 (bt878 #0 [sw]) [ 33.704000] tuner 1-0061: type set to 5 (Philips PAL_BG (FI1216 and compatibles)) [ 33.704000] tuner 1-0061: type set to 5 (Philips PAL_BG (FI1216 and compatibles)) [ 33.712000] bttv0: registered device video0 [ 33.712000] bttv0: registered device vbi0 [ 33.712000] bttv0: registered device radio0 [ 33.720000] bttv0: PLL: 28636363 => 35468950 .. ok [ 33.756000] ACPI: PCI Interrupt 0000:00:0b.1[A] -> Link [LNKD] -> GSI 12 (level, low) -> IRQ 12 [ 33.772000] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10 [ 33.772000] NVRM: loading NVIDIA Linux x86 Kernel Module 1.0-9639 Mon Apr 16 20:20:06 PDT 2007 [ 33.776000] ACPI: PCI Interrupt 0000:00:0c.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10 [ 33.888000] bt878: AUDIO driver version 0.0.0 loaded [ 35.192000] lp0: using parport0 (interrupt-driven). [ 35.280000] Adding 473876k swap on /dev/hda5. Priority:-1 extents:1 across:473876k [ 35.808000] EXT3 FS on hda1, internal journal [ 37.872000] No dock devices found. [ 38.040000] input: Power Button (FF) as /class/input/input2 [ 38.040000] ACPI: Power Button (FF) [PWRF] [ 38.076000] input: Power Button (CM) as /class/input/input3 [ 38.076000] ACPI: Power Button (CM) [PWRB] [ 38.096000] input: Sleep Button (CM) as /class/input/input4 [ 38.096000] ACPI: Sleep Button (CM) [SLPB] [ 38.672000] powernow: No powernow capabilities detected [ 41.796000] eth0: link down [ 42.616000] NET: Registered protocol family 10 [ 42.616000] lo: Disabled Privacy Extensions [ 42.616000] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 43.096000] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac) [ 43.096000] apm: overridden by ACPI. [ 45.272000] Failure registering capabilities with primary security module. [ 47.804000] lirc_dev: IR Remote Control driver registered, at major 61 [ 48.096000] ivtv: ==================== START INIT IVTV ==================== [ 48.096000] ivtv: version 1.0.0 (2.6.22-14-generic SMP mod_unload 586 ) loading [ 48.096000] ivtv: ==================== END INIT IVTV ==================== [ 48.348000] cx2388x v4l2 driver version 0.0.6 loaded [ 48.360000] lirc_i2c: chip 0x10005 found @ 0x18 (Hauppauge IR) [ 48.360000] lirc_dev: lirc_register_plugin: sample_rate: 10 [ 49.664000] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0. [ 49.664000] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode [ 49.664000] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode [ 523.232000] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 [ 523.232000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 530.660000] NET: Registered protocol family 17 [ 533.468000] eth0: no IPv6 routers present [ 640.136000] eth0: no IPv6 routers present [ 1066.648000] usb 3-1: new high speed USB device using ehci_hcd and address 2 [ 1066.780000] usb 3-1: configuration #1 chosen from 1 choice [ 1067.208000] usbcore: registered new interface driver libusual [ 1067.348000] Initializing USB Mass Storage driver... [ 1067.376000] scsi0 : SCSI emulation for USB Mass Storage devices [ 1067.388000] usbcore: registered new interface driver usb-storage [ 1067.388000] USB Mass Storage support registered. [ 1067.388000] usb-storage: device found at 2 [ 1067.388000] usb-storage: waiting for device to settle before scanning [ 1072.388000] usb-storage: device scan complete [ 1072.388000] scsi 0:0:0:0: Direct-Access Ext Hard Disk PQ: 0 ANSI: 4 [ 1072.496000] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) [ 1072.496000] sd 0:0:0:0: [sda] Write Protect is off [ 1072.496000] sd 0:0:0:0: [sda] Mode Sense: 10 00 00 00 [ 1072.496000] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 1072.500000] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) [ 1072.500000] sd 0:0:0:0: [sda] Write Protect is off [ 1072.500000] sd 0:0:0:0: [sda] Mode Sense: 10 00 00 00 [ 1072.500000] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 1072.500000] sda: sda1 [ 1072.528000] sd 0:0:0:0: [sda] Attached SCSI disk [ 1072.556000] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 1073.324000] usb 3-1: reset high speed USB device using ehci_hcd and address 2 [ 1088.436000] usb 3-1: device descriptor read/64, error -110 [ 1103.652000] usb 3-1: device descriptor read/64, error -110 [ 1103.868000] usb 3-1: reset high speed USB device using ehci_hcd and address 2 [ 1118.980000] usb 3-1: device descriptor read/64, error -110 [ 1134.196000] usb 3-1: device descriptor read/64, error -110 [ 1134.412000] usb 3-1: reset high speed USB device using ehci_hcd and address 2 [ 1139.432000] usb 3-1: device descriptor read/8, error -110