gaps in boot while on battery: [ 3.092828] ohci_hcd 0000:00:04.0: setting latency timer to 64 [ 3.092831] ohci_hcd 0000:00:04.0: OHCI Host Controller [ 3.092916] ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2 [ 3.093002] ohci_hcd 0000:00:04.0: irq 18, io mem 0xf6487000 (pause) [ 13.611857] Clocksource tsc unstable (delta = 4398045405880 ns) [ 13.614080] usb usb2: configuration #1 chosen from 1 choice [ 13.611857] Clocksource tsc unstable (delta = 4398045405880 ns) [ 13.614080] usb usb2: configuration #1 chosen from 1 choice [ 13.614176] hub 2-0:1.0: USB hub found [ 13.614245] hub 2-0:1.0: 2 ports detected (pause) [ 66.849293] ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 22 [ 66.849367] ehci_hcd 0000:00:02.1: PCI INT B -> Link[LUS2] -> GSI 22 (level, low) -> IRQ 22 [ 66.952571] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 66.952735] usb usb3: configuration #1 chosen from 1 choice [ 66.952766] hub 3-0:1.0: USB hub found [ 66.952775] hub 3-0:1.0: 7 ports detected (pause) [ 151.083790] ACPI: PCI Interrupt Link [Z019] enabled at IRQ 22 [ 151.083858] ehci_hcd 0000:00:04.1: PCI INT B -> Link[Z019] -> GSI 22 (level, low) -> IRQ 22 [ 151.089361] ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 4 [ 151.089466] ehci_hcd 0000:00:04.1: debug port 1 [ 151.089529] ehci_hcd 0000:00:04.1: cache line size of 64 is not supported [ 151.089535] ehci_hcd 0000:00:04.1: irq 22, io mem 0xf6489400 (pause) [ 165.763727] usb 2-1: new full speed USB device using ohci_hcd and address 2 [ 165.866916] ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 165.866916] ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 165.867105] usb usb4: configuration #1 chosen from 1 choice [ 165.867133] hub 4-0:1.0: USB hub found [ 165.867140] hub 4-0:1.0: 2 ports detected (pause) [ 174.346784] hub 2-0:1.0: unable to enumerate USB device on port 1 [ 183.274937] pata_acpi 0000:00:06.0: setting latency timer to 64 [ 165.867105] usb usb4: configuration #1 chosen from 1 choice [ 165.867133] hub 4-0:1.0: USB hub found [ 165.867140] hub 4-0:1.0: 2 ports detected [ 174.346784] hub 2-0:1.0: unable to enumerate USB device on port 1 (pause) [ 183.274937] pata_acpi 0000:00:06.0: setting latency timer to 64 [ 183.275380] ACPI: PCI Interrupt Link [LSI0] enabled at IRQ 23 [ 183.275645] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61. [ 183.276057] ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 20 [ 183.276124] forcedeth 0000:00:0a.0: PCI INT A -> Link[LMAC] -> GSI 20 (level, low) -> IRQ 20 [ 183.276211] forcedeth 0000:00:0a.0: setting latency timer to 64 (pause) [ 203.965474] forcedeth 0000:00:0a.0: ifname eth0, PHY OUI 0x732 @ 1, addr 00:1e:68:09:25:f6 [ 203.971700] forcedeth 0000:00:0a.0: highdma pwrctl mgmt timirq lnktim msi desc-v3 [ 204.032757] scsi0 : pata_amd [ 204.032916] scsi1 : pata_amd [ 204.033316] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x30c0 irq 14 [ 204.033381] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x30c8 irq 15 (pause) [ 218.112276] ata1.00: ATAPI: TSSTcorp CDDVDW TS-L632N, 0503, max MWDMA2 [ 218.112358] ata1: nv_mode_filter: 0x39f&0x39f->0x39f, BIOS=0x0 (0xc600) ACPI=0x39f (120:600:0x12) [ 204.033316] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x30c0 irq 14 [ 204.033381] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x30c8 irq 15 [ 218.112276] ata1.00: ATAPI: TSSTcorp CDDVDW TS-L632N, 0503, max MWDMA2 [ 218.112358] ata1: nv_mode_filter: 0x39f&0x39f->0x39f, BIOS=0x0 (0xc600) ACPI=0x39f (120:600:0x12) (pause) [ 222.963652] ata1.00: configured for MWDMA2 [ 222.963750] ata2: port disabled. ignoring. [ 222.985961] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray [ 222.985961] Uniform CD-ROM driver Revision: 3.20 [ 222.985961] sr 0:0:0:0: Attached scsi CD-ROM sr0 [ 222.996933] sr 0:0:0:0: Attached scsi generic sg0 type 5 (pause) [ 227.282911] usb 4-2: new high speed USB device using ehci_hcd and address 3 [ 227.283924] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00241b00964cac00] [ 222.985961] sr 0:0:0:0: Attached scsi CD-ROM sr0 [ 222.996933] sr 0:0:0:0: Attached scsi generic sg0 type 5 [ 227.282911] usb 4-2: new high speed USB device using ehci_hcd and address 3 [ 227.283924] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00241b00964cac00] (pause) [ 236.810969] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 236.811815] ata3.00: ATA-8: Hitachi HTS542525K9SA00, BBFOC32P, max UDMA/100 [ 236.811815] ata3.00: ATA-8: Hitachi HTS542525K9SA00, BBFOC32P, max UDMA/100 [ 236.811883] ata3.00: 488397168 sectors, multi 16: LBA48 [ 236.812879] ata3.00: configured for UDMA/100 [ 236.829246] usb 4-2: configuration #1 chosen from 1 choice (pause) [ 245.049681] ata4: SATA link down (SStatus 0 SControl 300) [ 250.020329] ata5: SATA link down (SStatus 0 SControl 300) [ 236.811883] ata3.00: 488397168 sectors, multi 16: LBA48 [ 236.812879] ata3.00: configured for UDMA/100 [ 236.829246] usb 4-2: configuration #1 chosen from 1 choice [ 245.049681] ata4: SATA link down (SStatus 0 SControl 300) (pause) [ 250.020329] ata5: SATA link down (SStatus 0 SControl 300) [ 250.020354] usb 2-1: new full speed USB device using ohci_hcd and address 3 [ 236.829246] usb 4-2: configuration #1 chosen from 1 choice [ 245.049681] ata4: SATA link down (SStatus 0 SControl 300) [ 250.020329] ata5: SATA link down (SStatus 0 SControl 300) [ 250.020354] usb 2-1: new full speed USB device using ohci_hcd and address 3 (pause) [ 257.590497] ata6: SATA link down (SStatus 0 SControl 300) [ 257.590681] scsi 2:0:0:0: Direct-Access ATA Hitachi HTS54252 BBFO PQ: 0 ANSI: 5 [ 258.319055] PM: Basic memory bitmaps created [ 258.364223] PM: Basic memory bitmaps freed [ 258.417871] kjournald starting. Commit interval 5 seconds [ 258.417871] EXT3-fs: mounted filesystem with ordered data mode. (pause) [ 293.086862] udevd version 124 started [ 294.185871] input: Power Button (FF) as /class/input/input2 [ 258.364223] PM: Basic memory bitmaps freed [ 258.417871] kjournald starting. Commit interval 5 seconds [ 258.417871] EXT3-fs: mounted filesystem with ordered data mode. [ 293.086862] udevd version 124 started (pause) [ 294.185871] input: Power Button (FF) as /class/input/input2 [ 294.228146] ACPI: Power Button (FF) [PWRF] [ 296.314872] ricoh-mmc: Ricoh MMC Controller disabling driver [ 296.314938] ricoh-mmc: Copyright(c) Philip Langdale [ 296.315481] ricoh-mmc: Ricoh MMC controller found at 0000:02:05.2 [1180:0843] (rev 12) [ 296.315569] ricoh-mmc: Controller is now disabled. (pause) [ 304.190771] nvidia: module license 'NVIDIA' taints kernel. [ 304.449547] ACPI: PCI Interrupt Link [LGPU] enabled at IRQ 16 [ 305.880139] loop: module loaded [ 305.944504] lp: driver loaded but no devices found [ 306.167548] Adding 5879748k swap on /dev/sda5. Priority:-1 extents:1 across:5879748k [ 306.199920] EXT3 FS on sda6, internal journal (pause) [ 313.017259] kjournald starting. Commit interval 5 seconds [ 313.009004] EXT3 FS on sda7, internal journal [ 306.199920] EXT3 FS on sda6, internal journal [ 313.017259] kjournald starting. Commit interval 5 seconds [ 313.009004] EXT3 FS on sda7, internal journal [ 313.009004] EXT3-fs: mounted filesystem with ordered data mode. (pause) [ 343.813541] type=1505 audit(1220373566.065:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=4244 [ 344.000157] type=1505 audit(1220373566.253:3): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=4251 [ 343.813541] type=1505 audit(1220373566.065:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=4244 [ 344.000157] type=1505 audit(1220373566.253:3): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=4251 [ 344.000367] type=1505 audit(1220373566.253:4): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=4251 [ 344.221296] ip_tables: (C) 2000-2006 Netfilter Core Team (pause) [ 410.936416] powernow-k8: Found 1 AMD Turion(tm) 64 X2 Mobile Technology TL-60 processors (2 cpu cores) (version 2.20.00) [ 410.936476] powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x11 [ 410.936476] powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x11 [ 410.936480] powernow-k8: 1 : fid 0xa (1800 MHz), vid 0x12 [ 410.936483] powernow-k8: 2 : fid 0x8 (1600 MHz), vid 0x13 [ 410.936486] powernow-k8: 3 : fid 0x0 (800 MHz), vid 0x1e (pause) [ 412.133820] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use) [ 431.343355] NET: Registered protocol family 10 [ 410.936480] powernow-k8: 1 : fid 0xa (1800 MHz), vid 0x12 [ 410.936483] powernow-k8: 2 : fid 0x8 (1600 MHz), vid 0x13 [ 410.936486] powernow-k8: 3 : fid 0x0 (800 MHz), vid 0x1e [ 412.133820] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use) (pause) [ 431.343355] NET: Registered protocol family 10 [ 431.344664] lo: Disabled Privacy Extensions [ 412.133820] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use) [ 431.343355] NET: Registered protocol family 10 [ 431.344664] lo: Disabled Privacy Extensions [ 431.946563] apm: BIOS not found. (pause) [ 435.986902] ppdev: user-space parallel port driver [ 448.837871] Bluetooth: L2CAP ver 2.10 [ 431.343355] NET: Registered protocol family 10 [ 431.344664] lo: Disabled Privacy Extensions [ 431.946563] apm: BIOS not found. [ 435.986902] ppdev: user-space parallel port driver (pause) [ 448.837871] Bluetooth: L2CAP ver 2.10 [ 448.837879] Bluetooth: L2CAP socket layer initialized [ 448.837879] Bluetooth: L2CAP socket layer initialized [ 448.873101] Bluetooth: RFCOMM socket layer initialized [ 448.874174] Bluetooth: RFCOMM TTY layer initialized [ 448.874182] Bluetooth: RFCOMM ver 1.10 (pause) [ 454.067655] eth0: no link during initialization. [ 454.068512] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 455.213227] wlan0: RX AssocResp from 00:e0:98:55:95:2c (capab=0x421 status=0 aid=2) [ 455.213241] wlan0: associated [ 455.213899] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 455.224144] wlan0: disassociating by local choice (reason=3) (pause) [ 465.955922] wlan0: no IPv6 routers present [ 473.538397] wlan0: authenticate with AP 00:e0:98:55:95:2c [ 455.213241] wlan0: associated [ 455.213899] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 455.224144] wlan0: disassociating by local choice (reason=3) [ 465.955922] wlan0: no IPv6 routers present (pause) [ 473.538397] wlan0: authenticate with AP 00:e0:98:55:95:2c [ 473.541049] wlan0: authenticated [ 473.541049] wlan0: authenticated [ 473.541070] wlan0: associate with AP 00:e0:98:55:95:2c [ 473.543105] wlan0: RX ReassocResp from 00:e0:98:55:95:2c (capab=0x421 status=0 aid=2) [ 473.543119] wlan0: associated (pause) [ 476.864169] RPC: Registered udp transport module. [ 476.864176] RPC: Registered tcp transport module.