Welcome to minicom 2.5 OPTIONS: I18n Compiled on May 2 2011, 10:05:24. Port /dev/ttyUSB0 Press CTRL-A Z for help on special keys Xloader version: dde59a2 2012-03-05 08:15:15 Built: Tue Apr 17 08:05:33 AM 2012 Configured for: 8500 B0 Running on chip ID: 8500B2 SECURITY_Init Boot scenario: NORMAL USB - Enabled: 0x00000001 Enum done: 0x00000000 Last reset reason: POWER_ON_RESET XP70_DATA_MBFFC: 0xFF000001 PWR_MNGT_STARTED 1 About to load MEMINIT After MEMINIT loaded verify_signedheader verify_signedheader done verify_payload hdr size: 0x000000D0 payload 0x40025C10 About to exec MEMINIT function SoC settings: INFO: Vendor ID = 0x000000ff, CS0 density = 0x00000054, CS1 density = 0x00000054 SoC settings: INFO: CS0 revision ID1 = 0x00000000, CS0 revision ID2 = 0x00000000 SoC settings: INFO: CS1 revision ID1 = 0x00000000, CS1 revision ID2 = 0x00000000 SoC settings: INFO: @(#)SOC-SETTINGS v4.0.4 db8500 v2 1000Mhz Mar 8 2012 13:13:02 SoC settings: INFO: AVS Enable, FVR21 value = : 0x87180960, FVR22 value = : 0x0013edf2 SoC settings: INFO: Memory size=0x40000000 (1024 MB) SoC settings: INFO: DDR Test Ended successfully. SoC settings: INFO: Requesting 1GHz from PRCMU SoC settings: INFO: Set 1GHz OK SoC settings: INFO: vmin = 1.3V, vbbp = +100mV, vbbn = +300mV SoC settings: INFO: Slow Parts [>>>>>..](Very Slow for N Transistor, Slow for P transistor) MEMINIT passed OK About to load NORMAL After NORMAL loaded verify_signedheader verify_signedheader done verify_payload hdr size: 0x00000000 payload 0x00000004 XL_DisableCachesMmu Before ENABLE_L2CC After ENABLE_L2CC Flush boot issw code Before call normal U-Boot 2012.04.01 (Jun 15 2012 - 08:36:24) CPU: ST-Ericsson db8500 v2 (Dual ARM Cortex A9) 998.400 Mhz DRAM: 1 GiB WARNING: Caches not enabled MMC: EMMC: 0, MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Hit any key to stop autoboot: 0 mmc1 is current device reading boot.scr 495 bytes read Running bootscript from mmc ... ## Executing script at 00100000 reading uImage 3940144 bytes read reading uInitrd 3138246 bytes read ## Booting kernel from Legacy Image at 00100000 ... Image Name: Linux Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3940080 Bytes = 3.8 MiB Load Address: 00008000 Entry Point: 00008000 ## Loading init Ramdisk from Legacy Image at 01000000 ... Image Name: initramfs Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 3138182 Bytes = 3 MiB Load Address: 00000000 Entry Point: 00000000 Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0 [ 0.000000] Linux version 3.7.0-1-linaro-u8500 (buildd@wani11) (gcc version 4.7.2 (Ubuntu/Linaro 4.7.2-2ubuntu0 [ 0.000000] Detailed version Linux 3.7.0-1-linaro-u8500 [ 0.000000] CPU: ARMv7 Processor [412fc091] revision 1 (ARMv7), cr=50c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Calao Systems Snowball platform [ 0.000000] Truncating RAM at 18000000-3fffffff to -2c3fffff (vmalloc region overlap). [ 0.000000] Memory policy: ECC disabled, Data cache writealloc [ 0.000000] DB8500 v2.2 [0x008500b2] [ 0.000000] PERCPU: Embedded 9 pages/cpu @c1894000 s14912 r8192 d13760 u36864 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 119928 [ 0.000000] Kernel command line: console=tty0 console=ttyAMA2,115200n8 root=UUID=7f0336b6-f93e-4027-895f-7456M [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 128MB 22MB 324MB = 474MB total [ 0.000000] Memory: 465676k/465676k available, 19700k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xec800000 - 0xff000000 ( 296 MB) [ 0.000000] lowmem : 0xc0000000 - 0xec400000 ( 708 MB) [ 0.000000] modules : 0xbf800000 - 0xc0000000 ( 8 MB) [ 0.000000] .text : 0xc0008000 - 0xc05c4528 (5874 kB) [ 0.000000] .init : 0xc05c5000 - 0xc05f2a40 ( 183 kB) [ 0.000000] .data : 0xc05f4000 - 0xc0662610 ( 442 kB) [ 0.000000] .bss : 0xc0662634 - 0xc0bfc70c (5737 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:670 [ 0.000000] PRCMU firmware: U9500, version 2.5.5 [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] console [tty0] enabled [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.000000] ... MAX_LOCK_DEPTH: 48 [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 [ 0.000000] ... CLASSHASH_SIZE: 4096 [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.000000] ... CHAINHASH_SIZE: 16384 [ 0.000000] memory used by lock dependency info: 3695 kB [ 0.000000] per task-struct memory footprint: 1152 bytes [ 0.002716] Calibrating delay loop... 1987.37 BogoMIPS (lpj=9936896) [ 0.059997] pid_max: default: 32768 minimum: 301 [ 0.060638] Security Framework initialized [ 0.060791] AppArmor: AppArmor initialized [ 0.061157] Mount-cache hash table entries: 512 [ 0.065612] CPU: Testing write buffer coherency: ok [ 0.066497] CPU0: thread -1, cpu 0, socket 3, mpidr 80000300 [ 0.066741] Setting up static identity map for 0x3ddb50 - 0x3ddb9c [ 0.066772] L310 cache controller enabled [ 0.066802] l2x0: 8 ways, CACHE_ID 0x410000c5, AUX_CTRL 0x7ec60800, Cache size: 524288 B [ 0.228149] CPU1: Booted secondary processor [ 0.306762] CPU1: thread -1, cpu 1, socket 3, mpidr 80000301 [ 0.307037] Brought up 2 CPUs [ 0.307128] SMP: Total of 2 processors activated (5971.96 BogoMIPS). [ 0.307403] 6CPU0 packing on CPU0 [ 0.307434] 6CPU1 packing on CPU0 [ 0.309326] devtmpfs: initialized [ 0.317016] EVM: security.selinux [ 0.317047] EVM: security.SMACK64 [ 0.317077] EVM: security.capability [ 0.319030] pinctrl core: initialized pinctrl subsystem [ 0.322845] regulator-dummy: no parameters [ 0.325012] NET: Registered protocol family 16 [ 0.325927] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.331726] gpio gpio.0: at address f812e000 [ 0.332580] gpio gpio.1: at address f812e080 [ 0.333435] gpio gpio.2: at address f800e000 [ 0.334259] gpio gpio.3: at address f800e080 [ 0.335083] gpio gpio.4: at address f800e100 [ 0.335876] gpio gpio.5: at address f800e180 [ 0.336700] gpio gpio.6: at address f811e000 [ 0.337585] gpio gpio.7: at address f811e080 [ 0.338439] gpio gpio.8: at address fa3fe000 [ 0.340454] pinctrl-nomadik pinctrl-db8500: initialized Nomadik pin control driver [ 0.344604] ab8500-core ab8500-core.0: detected chip, AB8500 rev. 3.0 [ 0.344726] ab8500-core ab8500-core.0: switch off cause(s) (0x20): [ 0.344757] "Battery level lower than power on reset threshold" [ 0.352050] ------------[ cut here ]------------ [ 0.352111] WARNING: at /build/buildd/linux-linaro-u8500-3.7-3.7.0/drivers/mfd/mfd-core.c:130 mfd_add_device+0) [ 0.352142] Modules linked in: [ 0.352203] [] (unwind_backtrace+0x1/0x98) from [] (warn_slowpath_common+0x33/0x48) [ 0.352233] [] (warn_slowpath_common+0x33/0x48) from [] (warn_slowpath_null+0x11/0x14) [ 0.352264] [] (warn_slowpath_null+0x11/0x14) from [] (mfd_add_device+0x1a1/0x1ac) [ 0.352325] [] (mfd_add_device+0x1a1/0x1ac) from [] (mfd_add_devices+0x65/0x7c) [ 0.352355] [] (mfd_add_devices+0x65/0x7c) from [] (ab8500_probe+0x343/0x438) [ 0.352386] [] (ab8500_probe+0x343/0x438) from [] (platform_drv_probe+0x11/0x14) [ 0.352447] [] (platform_drv_probe+0x11/0x14) from [] (driver_probe_device+0x51/0x178) [ 0.352478] [] (driver_probe_device+0x51/0x178) from [] (bus_for_each_drv+0x23/0x4c) [ 0.352508] [] (bus_for_each_drv+0x23/0x4c) from [] (device_attach+0x4d/0x5c) [ 0.352569] [] (device_attach+0x4d/0x5c) from [] (bus_probe_device+0x59/0x74) [ 0.352600] [] (bus_probe_device+0x59/0x74) from [] (device_add+0x399/0x410) [ 0.352630] [] (device_add+0x399/0x410) from [] (platform_device_add+0x9f/0x174) [ 0.352661] [] (platform_device_add+0x9f/0x174) from [] (mfd_add_device+0x159/0x1ac) [ 0.352722] [] (mfd_add_device+0x159/0x1ac) from [] (mfd_add_devices+0x65/0x7c) [ 0.352752] [] (mfd_add_devices+0x65/0x7c) from [] (db8500_prcmu_probe+0x107/0x158) [ 0.352783] [] (db8500_prcmu_probe+0x107/0x158) from [] (platform_drv_probe+0x11/0x14) [ 0.352813] [] (platform_drv_probe+0x11/0x14) from [] (driver_probe_device+0x51/0x178) [ 0.352874] [] (driver_probe_device+0x51/0x178) from [] (bus_for_each_drv+0x23/0x4c) [ 0.352905] [] (bus_for_each_drv+0x23/0x4c) from [] (device_attach+0x4d/0x5c) [ 0.352935] [] (device_attach+0x4d/0x5c) from [] (bus_probe_device+0x59/0x74) [ 0.352966] [] (bus_probe_device+0x59/0x74) from [] (device_add+0x399/0x410) [ 0.352996] [] (device_add+0x399/0x410) from [] (platform_device_add+0x9f/0x174) [ 0.353057] [] (platform_device_add+0x9f/0x174) from [] (platform_add_devices+0x21/0x4c) [ 0.353088] [] (platform_add_devices+0x21/0x4c) from [] (u8500_init_devices+0x95/0xac) [ 0.353149] [] (u8500_init_devices+0x95/0xac) from [] (snowball_init_machine+0xd/0x60) [ 0.353179] [] (snowball_init_machine+0xd/0x60) from [] (customize_machine+0xd/0x14) [ 0.353210] [] (customize_machine+0xd/0x14) from [] (do_one_initcall+0xc3/0x10c) [ 0.353271] [] (do_one_initcall+0xc3/0x10c) from [] (kernel_init+0xd3/0x208) [ 0.353302] [] (kernel_init+0xd3/0x208) from [] (ret_from_fork+0x11/0x3c) [ 0.353424] ---[ end trace da227214a82491b7 ]--- [ 0.355865] DB8500 PRCMU initialized [ 0.358062] mop500_audio_init: Register platform-device 'snd-soc-mop500'. [ 0.358428] Initialize MSP I2S-devices. [ 0.358428] Register platform-device 'ux500-msp-i2s', id 0, irq 63 [ 0.358795] Register platform-device 'ux500-msp-i2s', id 1, irq 94 [ 0.359161] Register platform-device 'ux500-msp-i2s', id 2, irq 130 [ 0.359497] Register platform-device 'ux500-msp-i2s', id 3, irq 94 [ 0.360900] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.360961] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.361938] db8500-vape: no parameters [ 0.362609] db8500-varm: no parameters [ 0.363128] db8500-vmodem: no parameters [ 0.363647] db8500-vpll: no parameters [ 0.364166] db8500-vsmps1: no parameters [ 0.364654] db8500-vsmps2: no parameters [ 0.365203] db8500-vsmps3: no parameters [ 0.365722] db8500-vrf1: no parameters [ 0.366241] db8500-sva-mmdsp: no parameters [ 0.366790] db8500-sva-mmdsp-ret: no parameters [ 0.367492] db8500-sva-pipe: no parameters [ 0.368041] db8500-sia-mmdsp: no parameters [ 0.368530] db8500-sia-mmdsp-ret: no parameters [ 0.369079] db8500-sia-pipe: no parameters [ 0.369567] db8500-sga: no parameters [ 0.369628] db8500-sga: supplied by db8500-vape [ 0.370452] db8500-b2r2-mcde: no parameters [ 0.370513] db8500-b2r2-mcde: supplied by db8500-vape [ 0.371154] db8500-esram12: no parameters [ 0.371643] db8500-esram12-ret: no parameters [ 0.372192] db8500-esram34: no parameters [ 0.372711] db8500-esram34-ret: no parameters [ 0.373199] Serial: AMBA PL011 UART driver [ 0.373840] uart0: ttyAMA0 at MMIO 0x80120000 (irq = 43) is a PL011 rev3 [ 0.375427] uart-pl011 uart1: could not get default pinstate [ 0.375488] uart1: ttyAMA1 at MMIO 0x80121000 (irq = 51) is a PL011 rev3 [ 0.376190] uart-pl011 uart2: could not get default pinstate [ 0.376251] uart2: ttyAMA2 at MMIO 0x80007000 (irq = 58) is a PL011 rev3 [ 1.289916] console [ttyAMA2] enabled [ 1.324920] bio: create slab at 0 [ 1.330566] dma40 dma40.0: hardware revision: 3 @ 0x801c0000 [ 1.336425] dma40 dma40.0: 7 of 8 physical DMA channels available [ 1.342529] dma40 dma40.0: [d40_phy_res_init] INFO: channel 4 is misconfigured (0) [ 1.350189] dma40 dma40.0: [d40_phy_res_init] INFO: channel 5 is misconfigured (0) [ 1.357788] dma40 dma40.0: [d40_phy_res_init] INFO: channel 6 is misconfigured (0) [ 1.392578] dma40 dma40.0: initialized [ 1.397247] EN-3V3: Failed to request enable GPIO337: -517 [ 1.402770] reg-fixed-voltage reg-fixed-voltage.1: Failed to register regulator: -517 [ 1.410766] platform reg-fixed-voltage.1: Driver reg-fixed-voltage requests probe deferral [ 1.421600] V-DISPLAY: 2500 <--> 2900 mV at 2500 mV [ 1.427368] V-eMMC1: 1100 <--> 3300 mV at 2900 mV [ 1.432830] V-MMC-SD: 1200 <--> 2910 mV at 2910 mV [ 1.438354] V-INTCORE: at 1250 mV [ 1.442382] V-TVOUT: 2000 mV [ 1.445892] LDO-USB: 3300 mV [ 1.449462] V-AUD: 2000 mV [ 1.452758] V-AMIC1: 2050 mV [ 1.456298] V-AMIC2: 2050 mV [ 1.459777] V-DMIC: 1800 mV [ 1.463256] V-CSI/DSI: 1200 mV [ 1.466461] V-CSI/DSI: Failed to create debugfs directory [ 1.477569] ab8500-usb ab8500-usb.0: AB8500 usb driver initialized [ 1.489166] NetLabel: Initializing [ 1.492614] NetLabel: domain hash size = 128 [ 1.496978] NetLabel: protocols = UNLABELED CIPSOv4 [ 1.502105] NetLabel: unlabeled traffic allowed by default [ 1.511260] ab8500-charger ab8500-charger.0: No platform data [ 1.517059] ab8500-charger: probe of ab8500-charger.0 failed with error -22 [ 1.524383] ab8500-btemp ab8500-btemp.0: No platform data [ 1.529876] ab8500-btemp: probe of ab8500-btemp.0 failed with error -22 [ 1.536834] ab8500-fg ab8500-fg.0: No platform data [ 1.541748] ab8500-fg: probe of ab8500-fg.0 failed with error -22 [ 1.548339] Switching to clocksource dbx500-prcmu-timer [ 1.599395] AppArmor: AppArmor Filesystem Enabled [ 1.636749] NET: Registered protocol family 2 [ 1.642669] TCP established hash table entries: 16384 (order: 5, 131072 bytes) [ 1.650360] TCP bind hash table entries: 16384 (order: 7, 589824 bytes) [ 1.660736] TCP: Hash tables configured (established 16384 bind 16384) [ 1.667572] TCP: reno registered [ 1.672271] UDP hash table entries: 256 (order: 2, 20480 bytes) [ 1.678405] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes) [ 1.685516] NET: Registered protocol family 1 [ 1.691070] RPC: Registered named UNIX socket transport module. [ 1.697021] RPC: Registered udp transport module. [ 1.701812] RPC: Registered tcp transport module. [ 1.706542] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.713623] Trying to unpack rootfs image as initramfs... [ 1.931030] Freeing initrd memory: 3064K [ 1.935272] CPU PMU: probing PMU on CPU 0 [ 1.939361] hw perfevents: enabled with ARMv7_Cortex_A9 PMU driver, 7 counters available [ 1.950775] audit: initializing netlink socket (disabled) [ 1.956359] type=2000 audit(1.200:1): initialized [ 2.065307] VFS: Disk quotas dquot_6.5.2 [ 2.069702] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 2.078338] NFS: Registering the id_resolver key type [ 2.083770] Key type id_resolver registered [ 2.088012] Key type id_legacy registered [ 2.092132] fuse init (API version 7.20) [ 2.097595] Btrfs loaded [ 2.100158] msgmni has been set to 915 [ 2.106842] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 2.114379] io scheduler noop registered [ 2.118316] io scheduler deadline registered [ 2.122741] io scheduler cfq registered (default) [ 2.131347] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 2.141204] uart-pl011 uart0: DMA channel TX dma0chan0 [ 2.146392] uart-pl011 uart0: DMA channel RX dma0chan1 [ 2.151733] uart-pl011 uart1: DMA channel TX dma0chan2 [ 2.156951] uart-pl011 uart1: DMA channel RX dma0chan3 [ 2.162139] uart-pl011 uart2: DMA channel TX dma0chan4 [ 2.167297] uart-pl011 uart2: DMA channel RX dma0chan5 [ 2.192291] brd: module loaded [ 2.206665] loop: module loaded [ 2.212860] mtdoops: mtd device (mtddev=name/number) must be supplied [ 2.220642] mmci-pl18x sdi4: Provided ocr_mask/setpower will not be used (using regulator instead) [ 2.229827] mmci-pl18x sdi4: mmc0: PL180 manf 80 rev4 at 0x80114000 irq 131,0 (pio) [ 2.237579] mmci-pl18x sdi4: DMA channels RX dma0chan6, TX dma0chan7 [ 2.304504] mmci-pl18x sdi0: Provided ocr_mask/setpower will not be used (using regulator instead) [ 2.313812] mmci-pl18x sdi0: mmc1: PL180 manf 80 rev4 at 0x80126000 irq 92,0 (pio) [ 2.321472] mmci-pl18x sdi0: DMA channels RX dma0chan8, TX dma0chan9 [ 2.364593] sdhci: Secure Digital Host Controller Interface driver [ 2.370788] sdhci: Copyright(c) Pierre Ossman [ 2.376403] tun: Universal TUN/TAP device driver, 1.6 [ 2.381500] tun: (C) 1999-2004 Max Krasnyansky [ 2.385437] mmc0: new high speed MMC card at address 0001 [ 2.387298] mmcblk0: mmc0:0001 3.53 GiB [ 2.387756] mmcblk0boot0: mmc0:0001 partition 1 2.00 MiB [ 2.388092] mmcblk0boot1: mmc0:0001 partition 2 2.00 MiB [ 2.408813] smsc911x: Driver version 2008-10-21 [ 2.413513] smsc911x smsc911x.0: Failed to get supply 'vdd33a': -517 [ 2.420013] smsc911x smsc911x.0 (unregistered net_device): couldn't get regulators -517 [ 2.428161] platform smsc911x.0: Driver smsc911x requests probe deferral [ 2.435180] PPP generic driver version 2.4.2 [ 2.441680] mousedev: PS/2 mouse device common for all mice [ 2.449951] input: AB8500 POn(PowerOn) Key as /devices/soc0/db8500-prcmu.0/ab8500-core.0/ab8500-poweron-key.0/0 [ 2.461303] mmcblk0: p1 p2 p3 p4 < p5 p6 p7 > [ 2.485412] ab8500-rtc ab8500-rtc.0: rtc core: registered ab8500-rtc as rtc0 [ 2.493988] mmcblk0boot1: unknown partition table [ 2.504119] rtc-pl031 rtc-pl031: rtc core: registered pl031 as rtc1 [ 2.511688] mmcblk0boot0: unknown partition table [ 2.516510] device-mapper: uevent: version 1.0.3 [ 2.522338] device-mapper: ioctl: 4.23.0-ioctl (2012-07-25) initialised: dm-devel@redhat.com [ 2.531066] cpufreq for DB8500 started [ 2.535034] db8500-cpufreq : Available frequencies: [ 2.540100] 200 Mhz [ 2.542388] 400 Mhz [ 2.544708] 800 Mhz [ 2.546997] 1000 Mhz [ 2.550781] cpuidle: using governor ladder [ 2.555816] cpuidle: using governor menu [ 2.560516] leds-gpio leds-gpio.0: pins are not configured from the driver [ 2.571594] oprofile: using timer interrupt. [ 2.576568] TCP: cubic registered [ 2.580047] Initializing XFRM netlink socket [ 2.584686] NET: Registered protocol family 10 [ 2.591064] NET: Registered protocol family 17 [ 2.595794] NET: Registered protocol family 15 [ 2.601074] NET: Registered protocol family 35 [ 2.605834] NET: Registered protocol family 37 [ 2.610565] Key type dns_resolver registered [ 2.615020] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 2 [ 2.622955] Registering SWP/SWPB emulation handler [ 2.629760] registered taskstats version 1 [ 2.648956] Key type encrypted registered [ 2.665924] db8500-esram34: disabling [ 2.669982] db8500-esram12: disabling [ 2.675964] EN-3V3: Failed to request enable GPIO337: -517 [ 2.681610] reg-fixed-voltage reg-fixed-voltage.1: Failed to register regulator: -517 [ 2.681762] input: gpio-keys as /devices/soc0/gpio-keys/input/input1 [ 2.696197] platform reg-fixed-voltage.1: Driver reg-fixed-voltage requests probe deferral [ 2.696228] ab8500-rtc ab8500-rtc.0: setting system clock to 2000-01-01 00:00:19 UTC (946684819) [ 2.713500] sm[ 2.715240] smsc911x smsc911x.0: Failed to get supply 'vdd33a': -517