same results. last system message is from the Mali driver. U-Boot 2009.11 (sept. 19 2011 - 17:03:11) CPU: ST-Ericsson db8500 v2 (Dual ARM Cortex A9) 998.400 Mhz I2C: ready DRAM: 1 GB MMC: MCDE: startup failed sec_bridge: ISSWAPI_FLUSH_BOOT_CODE: 2 EMMC: 0, MMC: 1 In: serial Out: serial Err: serial Net: smc911x-0 Hit any key to stop autoboot: 0 Partition info retrieved Reading /uImage 4681328 bytes read ## Booting kernel from Legacy Image at 00100000 ... Image Name: Linux Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4681264 Bytes = 4.5 MB Load Address: 00008000 Entry Point: 00008000 Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0 [ 0.000000] Linux version 3.2.0-1000-ux500 (buildd@anacardiaceae) (gcc versi2 [ 0.000000] CPU: ARMv7 Processor [412fc091] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instructie [ 0.000000] Machine: ST-Ericsson Snowball platform [ 0.000000] Only cachepolicy=writeback supported on ARMv6 and later [ 0.000000] Memory policy: ECC disabled, Data cache writealloc [ 0.000000] DB8500 v2.2 [0x008500b2] [ 0.000000] Reserving 1MB of memory at 86MB for crashkernel (System RAM: 760) [ 0.000000] PERCPU: Embedded 8 pages/cpu @c1605000 s12064 r8192 d12512 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pa0 [ 0.000000] Kernel command line: cachepolicy=writealloc noinitrd init=init iM [ 0.000000] Startup graphics support [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 383MB 640MB = 1023MB total [ 0.000000] Memory: 1023112k/1023112k available, 24440k reserved, 270336K him [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xf0000000 - 0xf7800000 ( 120 MB) [ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc08f263c (9130 kB) [ 0.000000] .init : 0xc08f3000 - 0xc0948f20 ( 344 kB) [ 0.000000] .data : 0xc094a000 - 0xc09d12f8 ( 541 kB) [ 0.000000] .bss : 0xc09d131c - 0xc0dfbb2c (4267 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:640 [ 0.000000] PRCMU firmware version 3.4.3 [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 1s [ 0.000000] Console: colour dummy device 80x30 [ 0.149993] Calibrating delay using timer specific routine.. 4.80 BogoMIPS () [ 0.150054] pid_max: default: 32768 minimum: 301 [ 0.150268] Security Framework initialized [ 0.150390] AppArmor: AppArmor initialized [ 0.150543] Mount-cache hash table entries: 512 [ 0.151641] Initializing cgroup subsys cpuacct [ 0.151763] CPU: Testing write buffer coherency: ok [ 0.151824] ftrace: allocating 24539 entries in 73 pages [ 0.174652] CPU0: thread -1, cpu 0, socket 3, mpidr 80000300 [ 0.174835] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 countee [ 0.174926] L310 cache controller enabled [ 0.174926] l2x0: 8 ways, CACHE_ID 0x410000c5, AUX_CTRL 0x7e060800, Cache siB [ 0.275360] CPU1: Booted secondary processor [ 0.275390] CPU1: thread -1, cpu 1, socket 3, mpidr 80000301 [ 0.275421] Brought up 2 CPUs [ 0.275451] SMP: Total of 2 processors activated (9.61 BogoMIPS). [ 0.276123] devtmpfs: initialized [ 0.281433] print_constraints: dummy: [ 0.281860] NET: Registered protocol family 16 [ 0.285034] gpio gpio.0: Bits 0-31 at address f812e000 [ 0.285491] gpio gpio.1: Bits 32-63 at address f812e080 [ 0.286102] gpio gpio.2: Bits 64-95 at address f800e000 [ 0.286499] gpio gpio.3: Bits 96-127 at address f800e080 [ 0.287109] gpio gpio.4: Bits 128-159 at address f800e100 [ 0.287567] gpio gpio.5: Bits 160-191 at address f800e180 [ 0.288177] gpio gpio.6: Bits 192-223 at address f811e000 [ 0.288635] gpio gpio.7: Bits 224-255 at address f811e080 [ 0.289154] gpio gpio.8: Bits 256-287 at address fa3fe000 [ 0.294799] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint. [ 0.294830] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.296844] stm stm: STM-Trace driver probed successfully [ 0.297576] print_constraints: db8500-vape: [ 0.297851] print_constraints: db8500-varm: [ 0.298095] print_constraints: db8500-vmodem: [ 0.298309] print_constraints: db8500-vpll: [ 0.298553] print_constraints: db8500-vsmps1: [ 0.298767] print_constraints: db8500-vsmps2: [ 0.298980] print_constraints: db8500-vsmps3: [ 0.299224] print_constraints: db8500-vrf1: [ 0.299468] print_constraints: db8500-sva-mmdsp: [ 0.299499] set_supply: db8500-sva-mmdsp: supplied by db8500-vape [ 0.299743] print_constraints: db8500-sva-mmdsp-ret: [ 0.300018] print_constraints: db8500-sva-pipe: [ 0.300048] set_supply: db8500-sva-pipe: supplied by db8500-vape [ 0.300292] print_constraints: db8500-sia-mmdsp: [ 0.300323] set_supply: db8500-sia-mmdsp: supplied by db8500-vape [ 0.300598] print_constraints: db8500-sia-mmdsp-ret: [ 0.300811] print_constraints: db8500-sia-pipe: [ 0.300842] set_supply: db8500-sia-pipe: supplied by db8500-vape [ 0.301116] print_constraints: db8500-sga: [ 0.301147] set_supply: db8500-sga: supplied by db8500-vape [ 0.301422] print_constraints: db8500-b2r2-mcde: [ 0.301422] set_supply: db8500-b2r2-mcde: supplied by db8500-vape [ 0.301727] print_constraints: db8500-esram12: [ 0.301727] set_supply: db8500-esram12: supplied by db8500-vape [ 0.302001] print_constraints: db8500-esram12-ret: [ 0.302246] print_constraints: db8500-esram34: [ 0.302246] set_supply: db8500-esram34: supplied by db8500-vape [ 0.302551] print_constraints: db8500-esram34-ret: [ 0.302825] DB8500 PRCMU initialized [ 0.303100] ab8500-i2c ab8500-i2c.0: detected chip, revision: 0x30 [ 0.303161] ab8500-i2c ab8500-i2c.0: switch off status: 0x20 [ 0.308929] HWMEM: hwmem_paddr != PAGE_ALIGN(hwmem_paddr) || hwmem_size != P0 [ 0.336456] bio: create slab at 0 [ 0.337310] dma40 dma40.0: managed by runtime pm: regulator [ 0.337402] dma40 dma40.0: hardware revision: 3 @ 0x801c0000 [ 0.337463] dma40 dma40.0: 6 of 8 physical DMA channels available [ 0.337463] dma40 dma40.0: [d40_phy_res_init] INFO: channel 4 is misconfigur) [ 0.337493] dma40 dma40.0: [d40_phy_res_init] INFO: channel 5 is misconfigur) [ 0.337493] dma40 dma40.0: [d40_phy_res_init] INFO: channel 6 is misconfigur) [ 0.348205] dma40 dma40.0: initialized [ 0.348907] print_constraints: EN-3V3: 3300 mV [ 0.349365] print_constraints: WLAN-VBAT: 3600 mV [ 0.351501] print_constraints: ab8500-ext-supply3: 3400 mV [ 0.351806] print_constraints: V-DISPLAY: 2800 <--> 3300 mV at 2800 mV [ 0.351867] set_supply: V-DISPLAY: supplied by ab8500-ext-supply3 [ 0.352203] print_constraints: V-eMMC1: 1100 <--> 3300 mV at 2900 mV normal [ 0.352233] set_supply: V-eMMC1: supplied by ab8500-ext-supply3 [ 0.352569] print_constraints: V-MMC-SD: 1200 <--> 2910 mV at 2910 mV normal [ 0.352600] set_supply: V-MMC-SD: supplied by ab8500-ext-supply3 [ 0.352905] print_constraints: V-INTCORE: 1250 <--> 1350 mV at 1250 mV norma [ 0.353179] print_constraints: V-TVOUT: 2000 mV [ 0.353485] print_constraints: LDO-USB: 3300 mV [ 0.353729] print_constraints: V-AUD: 2000 mV [ 0.353973] print_constraints: V-AMIC1: 2050 mV [ 0.354217] print_constraints: V-AMIC2: 2050 mV [ 0.354492] print_constraints: V-DMIC: 1800 mV [ 0.354736] print_constraints: V-CSI-DSI: 1200 mV [ 0.354980] print_constraints: V-SYSCLKREQ-2: 0 mV [ 0.355285] print_constraints: V-SYSCLKREQ-4: 0 mV [ 0.357147] Serial: AMBA PL011 UART driver [ 0.357360] uart0: ttyAMA0 at MMIO 0x80120000 (irq = 43) is a PL011 rev3 [ 0.375335] uart1: ttyAMA1 at MMIO 0x80121000 (irq = 51) is a PL011 rev3 [ 0.405334] uart2: ttyAMA2 at MMIO 0x80007000 (irq = 58) is a PL011 rev3 [ 1.132171] console [ttyAMA2] enabled [ 1.167358] hwmem hwmem.0: Probed OK [ 1.173431] SCSI subsystem initialized [ 1.177246] ssp-pl022 ssp0: managed by runtime pm: regulator [ 1.183044] ssp-pl022 ssp0: ARM PL022 driver, device ID: 0x01080022 [ 1.189331] pl022: mapped registers from 0x80002000 to f0040000 [ 1.195251] ssp-pl022 ssp0: Unbalanced pm_runtime_enable! [ 1.200744] ssp-pl022 ssp0: setup for DMA on RX dma0chan0, TX dma0chan1 [ 1.207672] ssp-pl022 ssp0: runtime pm suspend before resume [ 1.214233] usbcore: registered new interface driver usbfs [ 1.219879] usbcore: registered new interface driver hub [ 1.225372] usbcore: registered new device driver usb [ 1.230987] ab8500-usb ab8500-usb.0: managed by runtime pm: pins [ 1.237915] ab8500-usb ab8500-usb.0: revision 0x30 driver initialized [ 1.244354] prcmu qos: get cpufreq policy failed (cpu0) [ 1.249603] prcmu qos: get cpufreq policy failed (cpu1) [ 1.256011] nmk-i2c nmk-i2c.0: managed by runtime pm: pins [ 1.261718] nmk-i2c nmk-i2c.0: initialize Nomadik I2C0 at 80004000 on virtua0 [ 1.270507] nmk-i2c nmk-i2c.1: managed by runtime pm: pins [ 1.276184] nmk-i2c nmk-i2c.1: initialize Nomadik I2C1 at 80122000 on virtua0 [ 1.284759] nmk-i2c nmk-i2c.2: managed by runtime pm: pins [ 1.290466] nmk-i2c nmk-i2c.2: initialize Nomadik I2C2 at 80128000 on virtua0 [ 1.298858] power state: unbalanced enable/disable calls [ 1.304382] nmk-i2c nmk-i2c.3: managed by runtime pm: pins [ 1.310089] nmk-i2c nmk-i2c.3: initialize Nomadik I2C3 at 80110000 on virtua0 [ 1.320007] Advanced Linux Sound Architecture Driver Version 1.0.24. [ 1.327331] Bluetooth: Core ver 2.16 [ 1.331085] NET: Registered protocol family 31 [ 1.335510] Bluetooth: HCI device and connection manager initialized [ 1.341888] Bluetooth: HCI socket layer initialized [ 1.346771] Bluetooth: L2CAP socket layer initialized [ 1.351837] Bluetooth: SCO socket layer initialized [ 1.357177] cfg80211: Calling CRDA to update world regulatory domain [ 1.363708] NetLabel: Initializing [ 1.367126] NetLabel: domain hash size = 128 [ 1.371459] NetLabel: protocols = UNLABELED CIPSOv4 [ 1.376464] NetLabel: unlabeled traffic allowed by default [ 1.406829] ab8500-btemp ab8500-btemp.0: Battery identified as unknown, resim [ 1.415374] ab8500-btemp ab8500-btemp.0: failed to identify the battery [ 1.435333] Switching to clocksource dbx500-prcmu-timer [ 1.454467] AppArmor: AppArmor Filesystem Enabled [ 1.459167] MCDE subsystem init begin [ 1.463043] mcde mcde: MCDE iomap: 0xA0350000->0xF004A000 [ 1.468444] mcde mcde: MCDE DSI0 iomap: 0xA0351000->0xF004C000 [ 1.474334] mcde mcde: MCDE DSI1 iomap: 0xA0352000->0xF004E000 [ 1.480194] mcde mcde: MCDE DSI2 iomap: 0xA0353000->0xF0050000 [ 1.486236] mcde mcde: Probe HW [ 1.489440] mcde mcde: MCDE HW revision 3.0.8.0 [ 1.494049] mcde mcde: V2 HW [ 1.498413] MCDE subsystem init done [ 1.519165] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) [ 1.525970] musb-hdrc musb-hdrc: USB OTG mode controller at f0060000 using D5 [ 1.534759] NET: Registered protocol family 2 [ 1.539367] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 1.547363] TCP established hash table entries: 131072 (order: 8, 1048576 by) [ 1.556701] TCP bind hash table entries: 65536 (order: 7, 786432 bytes) [ 1.564178] TCP: Hash tables configured (established 131072 bind 65536) [ 1.570800] TCP reno registered [ 1.573944] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 1.579895] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 1.586547] NET: Registered protocol family 1 [ 1.591186] NetWinder Floating Point Emulator V0.97 (double precision) [ 1.599670] ux500-product: JTAG is disabled [ 1.606170] audit: initializing netlink socket (disabled) [ 1.611633] type=2000 audit(0.890:1): initialized [ 1.631378] highmem bounce pool size: 64 pages [ 1.636199] VFS: Disk quotas dquot_6.5.2 [ 1.640350] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.647644] Installing v9fs 9p2000 file system support [ 1.653259] msgmni has been set to 1470 [ 1.657897] io scheduler noop registered [ 1.661834] io scheduler deadline registered (default) [ 1.667053] io scheduler cfq registered [ 1.670959] mcde_display_generic_init [ 1.675018] mcde_display_sony_acx424akp_init [ 1.685028] av8100 0-0070: chip version:2 [ 1.745971] i2c-core: driver [av8100] using legacy suspend method [ 1.752105] i2c-core: driver [av8100] using legacy resume method [ 1.758117] b2r2_init [ 1.763122] B2R2_MEM: Creating heap for size 16384 bytes [ 1.769561] uart-pl011 uart0: no DMA platform data [ 1.774383] uart-pl011 uart1: no DMA platform data [ 1.779174] uart-pl011 uart2: no DMA platform data [ 1.784423] [drm] Initialized drm 1.1.0 20060810 [ 1.790069] Mali<2>: [ 1.792358] Mali<2>: Inserting Mali v8 device driver. [ 1.797515] Mali<2>: Compiled: Mar 5 2012, time: 17:00:11. [ 1.803100] Mali<2>: Svn revision: [ 1.806579] Mali<2>: MMU memory system initializing [ 1.811492] Mali<2>: Rendercore: subsystem global mutex initialized [ 1.817749] Mali<2>: Core: subsystem_init: Mali-400 PP [ 1.822906] Mali<2>: Core: subsystem_init: Mali-400 GP [ 1.828033] Mali<2>: Mali L2 cache system initializing [ 1.833282] create_regulator: db8500-sga: Failed to create debugfs directory [ 1.840576] Mali<2>: MMU registered [ 1.844116] Mali<2>: MMU registered [ 1.847595] Mali<1>: Failed to request memory region Mali SDRAM (0x08000000 ) [ 1.855804] Mali<2>: Mali L2 cache system terminating [ 1.860839] Mali<2>: Core: subsystem_cleanup: Mali-400 GP [ 1.866363] Mali<2>: Core: subsystem_cleanup: Mali-400 PP