Panda: Bootup failures observed when HDMI cable is connected

[Abhishek Paliwal]

With build:
https://android-build.linaro.org/builds/~linaro-android/panda/#build=418

Created image on sd card and booted up device:
Issue:
1. Getting consistent bootup failures when HDMI cable is connected to device and TV/Monitor.
(Connected HDMI cable to the HDMI port next to ethernet port.)

2. Device gets stuck while booting up ,HDMI display does not come up

3. Serial Logs displays: "omap_hwmod: dss_core: _wait_target_disable failed " continously...

Note:
Workaround is to : Remove HDMI -bootup device - now connect HDMI - No issues now

Bootup Logs below:
================

U-Boot SPL 2011.09 (Dec 08 2011 - 05:26:47)
Texas Instruments OMAP4430 ES2.2
OMAP SD/MMC: 0
reading u-boot.img
reading u-boot.img

U-Boot 2011.09 (Dec 08 2011 - 05:26:47)

CPU : OMAP4430
Board: OMAP4 Panda
I2C: ready
DRAM: 1 GiB
WARNING: Caches not enabled
MMC: OMAP SD/MMC: 0
Using default environment

In: serial
Out: serial
Err: serial
Net: No ethernet found.
Hit any key to stop autoboot: 0
reading uEnv.txt

** Unable to read "uEnv.txt" from mmc 0:1 **
reading boot.scr

462 bytes read
Loaded script from boot.scr
Running bootscript from mmc0 ...
## Executing script at 82000000
reading uImage

4525728 bytes read
reading uInitrd

161691 bytes read
## Booting kernel from Legacy Image at 80200000 ...
   Image Name: Linux-3.2.0-rc4-21784-g192e11a
   Image Type: ARM Linux Kernel Image (uncompressed)
   Data Size: 4525664 Bytes = 4.3 MiB
   Load Address: 80008000
   Entry Point: 80008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 81600000 ...
   Image Name: Android Ramdisk Image
   Image Type: ARM Linux RAMDisk Image (gzip compressed)
   Data Size: 161627 Bytes = 157.8 KiB
   Load Address: 00000000
   Entry Point: 00000000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0
[ 0.000000] Linux version 3.2.0-rc4-21784-g192e11a (jenkins-build@domU-12-31-39-05-69-81) (gcc version 4.6.2 (Linaro GCC 4.6-2011.11) ) #1 SMP Thu Dec 8 06:15:32 UTC 2011
[ 0.000000] CPU: ARMv7 Processor [411fc092] revision 2 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: OMAP4 Panda board
[ 0.000000] Truncating RAM at a0000000-bfffffff to -afffffff (vmalloc region overlap).
[ 0.000000] Reserving 50331648 bytes SDRAM for VRAM
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] OMAP4430 ES2.2
[ 0.000000] PERCPU: Embedded 8 pages/cpu @c1531000 s10944 r8192 d13632 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 168448
[ 0.000000] Kernel command line: console=tty0 console=ttyO2,115200n8 rootwait ro earlyprintk fixrtc nocompcache vram=48M omapfb.vram=0:24M,1:24M mem=456M@0x80000000 mem=512M@0xA0000000 init=/init androidboot.console=ttyO2
[ 0.000000]
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 456MB 208MB = 664MB total
[ 0.000000] Memory: 657676k/657676k available, 71412k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xf0800000 - 0xf8000000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc07ce398 (7961 kB)
[ 0.000000] .init : 0xc07cf000 - 0xc0821ac0 ( 331 kB)
[ 0.000000] .data : 0xc0822000 - 0xc0854340 ( 201 kB)
[ 0.000000] .bss : 0xc08cf9e8 - 0xc0f23780 (6480 kB)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:410
[ 0.000000] omap_hwmod: dpll_mpu_m2_ck: missing clockdomain for dpll_mpu_m2_ck.
[ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz
[ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [tty0] enabled
[ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8
[ 0.000000] ... MAX_LOCK_DEPTH: 48
[ 0.000000] ... MAX_LOCKDEP_KEYS: 8191
[ 0.000000] ... CLASSHASH_SIZE: 4096
[ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384
[ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768
[ 0.000000] ... CHAINHASH_SIZE: 16384
[ 0.000000] memory used by lock dependency info: 3695 kB
[ 0.000000] per task-struct memory footprint: 1152 bytes
[ 0.002593] Calibrating delay loop... 1576.53 BogoMIPS (lpj=6156288)
[ 0.062469] pid_max: default: 32768 minimum: 301
[ 0.063171] Security Framework initialized
[ 0.063476] Mount-cache hash table entries: 512
[ 0.067779] CPU: Testing write buffer coherency: ok
[ 0.068756] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.068878] Calibrating local timer... 386.27MHz.
[ 0.109558] L310 cache controller enabled
[ 0.109588] l2x0: 16 ways, CACHE_ID 0x410000c4, AUX_CTRL 0x7e470000, Cache size: 1048576 B
[ 0.112426] CPU1: Booted secondary processor
[ 0.140014] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.140045] CPU1: Unknown IPI message 0x1
[ 0.140228] Brought up 2 CPUs
[ 0.140258] SMP: Total of 2 processors activated (3115.31 BogoMIPS).
[ 0.150360] omap_hwmod: l3_div_ck: missing clockdomain for l3_div_ck.
[ 0.153747] omap_hwmod: dmm: _wait_target_disable failed
[ 0.156372] omap_hwmod: emif_fw: _wait_target_disable failed
[ 0.158996] omap_hwmod: l3_main_1: _wait_target_disable failed
[ 0.161621] omap_hwmod: l3_main_2: _wait_target_disable failed
[ 0.164276] omap_hwmod: l4_abe: _wait_target_disable failed
[ 0.166870] omap_hwmod: l4_cfg: _wait_target_disable failed
[ 0.169494] omap_hwmod: l4_per: _wait_target_disable failed
[ 0.172607] omap_hwmod: l4_wkup: _wait_target_disable failed
[ 0.175231] omap_hwmod: dma_system: _wait_target_disable failed
[ 0.177947] omap_hwmod: dss_core: _wait_target_disable failed
[ 0.180572] omap_hwmod: dss_dispc: _wait_target_disable failed
[ 0.183197] omap_hwmod: dss_dsi1: _wait_target_disable failed
[ 0.185852] omap_hwmod: dss_dsi2: _wait_target_disable failed
[ 0.188476] omap_hwmod: dss_hdmi: _wait_target_disable failed
[ 0.191101] omap_hwmod: dss_rfbi: _wait_target_disable failed
[ 0.193725] omap_hwmod: dss_venc: _wait_target_disable failed
[ 0.197326] omap_hwmod: mailbox: _wait_target_disable failed
[ 0.200042] omap_hwmod: mcpdm: cannot be enabled (3)
[ 0.202911] omap_hwmod: spinlock: _wait_target_disable failed
[ 0.209228] print_constraints: dummy:
[ 0.210449] NET: Registered protocol family 16
[ 0.211090] GPMC revision 6.0
[ 0.217834] OMAP GPIO hardware version 0.1
[ 0.225921] omap_mux_init: Add partition: #1: core, flags: 2
[ 0.227722] omap_mux_init: Add partition: #2: wkup, flags: 2
[ 0.227874] error setting wl12xx data
[ 0.241485] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.241516] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.253387] OMAP DMA hardware revision 0.0
[ 0.300872] bio: create slab <bio-0> at 0
[ 0.303009] print_constraints: vwl1271: 1800 mV
[ 0.306152] SCSI subsystem initialized
[ 0.310516] usbcore: registered new interface driver usbfs
[ 0.311126] usbcore: registered new interface driver hub
[ 0.311523] usbcore: registered new device driver usb
[ 0.323211] omap_i2c omap_i2c.1: bus 1 rev2.4.0 at 400 kHz
[ 0.326263] Skipping twl internal clock init and using bootloader value (unknown osc rate)
[ 0.327392] twl6030: PIH (irq 39) chaining IRQs 368..387
[ 0.329315] print_constraints: VUSB: 3300 mV normal standby
[ 0.528991] twl6030_usb twl6030_usb: Initialized TWL6030 USB module
[ 0.530609] print_constraints: VMMC: 1200 <--> 3000 mV at 3000 mV normal standby
[ 0.531982] print_constraints: VPP: 1800 <--> 2500 mV at 1900 mV normal standby
[ 0.533325] print_constraints: VCXIO: 1800 mV normal standby
[ 0.534515] print_constraints: VDAC: 1800 mV normal standby
[ 0.535736] print_constraints: VAUX2_6030: 1200 <--> 2800 mV at 1800 mV normal standby
[ 0.537139] print_constraints: VAUX3_6030: 1000 <--> 3000 mV at 1200 mV normal standby
[ 0.538208] print_constraints: CLK32KG:
[ 0.539276] print_constraints: VANA: 2100 mV normal standby
[ 0.551635] omap_i2c omap_i2c.2: bus 2 rev2.4.0 at 400 kHz
[ 0.566864] omap_i2c omap_i2c.3: bus 3 rev2.4.0 at 100 kHz
[ 0.582122] omap_i2c omap_i2c.4: bus 4 rev2.4.0 at 400 kHz
[ 0.584655] Advanced Linux Sound Architecture Driver Version 1.0.24.
[ 0.589538] Switching to clocksource 32k_counter
[ 0.590087] cfg80211: Calling CRDA to update world regulatory domain
[ 0.670562] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
[ 0.672485] musb-hdrc musb-hdrc: USB OTG mode controller at fc0ab000 using PIO, IRQ 124
[ 0.673431] NET: Registered protocol family 2
[ 0.673919] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.675323] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.678039] TCP bind hash table entries: 65536 (order: 9, 2359296 bytes)
[ 0.703430] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.703613] TCP reno registered
[ 0.703674] UDP hash table entries: 512 (order: 3, 40960 bytes)
[ 0.704132] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes)
[ 0.705169] NET: Registered protocol family 1
[ 0.705780] Trying to unpack rootfs image as initramfs...
[ 0.718048] Freeing initrd memory: 156K
[ 0.718078] NetWinder Floating Point Emulator V0.97 (double precision)
[ 0.906463] ashmem: initialized
[ 0.907073] VFS: Disk quotas dquot_6.5.2
[ 0.907287] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.910278] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 0.911651] Btrfs loaded
[ 0.911682] msgmni has been set to 1284
[ 0.914276] io scheduler noop registered
[ 0.914306] io scheduler deadline registered
[ 0.914428] io scheduler cfq registered (default)
[ 0.916534] OMAP DSS rev 4.0
[ 0.919158] omap_hwmod: dss_core: _wait_target_disable failed
[ 0.922729] omap_hwmod: dss_dispc: _wait_target_disable failed
[ 0.925506] omap_hwmod: dss_core: _wait_target_disable failed
[ 0.930694] omap_hwmod: dss_dispc: _wait_target_disable failed
[ 0.933319] omap_hwmod: dss_core: _wait_target_disable failed
[ 0.934173] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.051483] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 104) is a OMAP UART0
[ 1.089965] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 105) is a OMAP UART1
[ 1.105590] omap_uart.2: ttyO2 at MMIO 0x48020000 (irq = 106) is a OMAP UART2
[ 1.973449] console [ttyO2] enabled
[ 1.996337] omap_uart.3: ttyO3 at MMIO 0x4806e000 (irq = 102) is a OMAP UART3
[ 2.045959] brd: module loaded
[ 2.060424] loop: module loaded
[ 2.067718] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 2.074554] omap2-nand driver initializing
[ 2.079284] OneNAND driver initializing
[ 2.087829] usbcore: registered new interface driver usb8xxx
[ 2.093780] libertas_sdio: Libertas SDIO driver
[ 2.098571] libertas_sdio: Copyright Pierre Ossman
[ 2.104187] usbcore: registered new interface driver asix
[ 2.110198] usbcore: registered new interface driver cdc_ether
[ 2.116668] usbcore: registered new interface driver smsc75xx
[ 2.123046] usbcore: registered new interface driver smsc95xx
[ 2.129425] usbcore: registered new interface driver net1080
[ 2.135650] usbcore: registered new interface driver cdc_subset
[ 2.142181] usbcore: registered new interface driver zaurus
[ 2.148071] cdc_ncm: 04-Aug-2011
[ 2.151763] usbcore: registered new interface driver cdc_ncm
[ 2.158630] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.166015] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
[ 2.174804] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
[ 2.183074] ehci-omap ehci-omap.0: irq 109, io mem 0x4a064c00
[ 2.199340] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
[ 2.206054] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.213226] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.220825] usb usb1: Product: OMAP-EHCI Host Controller
[ 2.226440] usb usb1: Manufacturer: Linux 3.2.0-rc4-21784-g192e11a ehci_hcd
[ 2.233764] usb usb1: SerialNumber: ehci-omap.0
[ 2.241180] hub 1-0:1.0: USB hub found
[ 2.245239] hub 1-0:1.0: 3 ports detected
[ 2.277984] usbcore: registered new interface driver cdc_wdm
[ 2.283966] Initializing USB Mass Storage driver...
[ 2.289459] usbcore: registered new interface driver usb-storage
[ 2.295806] USB Mass Storage support registered.
[ 2.301513] usbcore: registered new interface driver libusual
[ 2.307891] usbcore: registered new interface driver usbtest
[ 2.516082] gadget: Mass Storage Function, version: 2009/09/11
[ 2.522338] gadget: Number of LUNs=1
[ 2.526184] lun0: LUN: removable file: (no medium)
[ 2.532226] gadget: android_usb ready
[ 2.731262] musb-hdrc musb-hdrc: MUSB HDRC host driver
[ 2.738128] musb-hdrc musb-hdrc: new USB bus registered, assigned bus number 2
[ 2.746185] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.753326] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.760955] usb usb2: Product: MUSB HDRC host driver
[ 2.766174] usb usb2: Manufacturer: Linux 3.2.0-rc4-21784-g192e11a musb-hcd
[ 2.773529] usb usb2: SerialNumber: musb-hdrc
[ 2.779998] hub 2-0:1.0: USB hub found
[ 2.784057] hub 2-0:1.0: 1 port detected
[ 2.790924] mousedev: PS/2 mouse device common for all mice
[ 2.800537] twl_rtc twl_rtc: Power up reset detected.
[ 2.806823] twl_rtc twl_rtc: Enabling TWL-RTC.
[ 2.814117] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
[ 2.821197] i2c /dev entries driver
[ 2.828308] lirc_dev: IR Remote Control driver registered, major 250
[ 2.835205] IR NEC protocol handler initialized
[ 2.839996] IR RC5(x) protocol handler initialized
[ 2.845031] IR RC6 protocol handler initialized
[ 2.849822] IR JVC protocol handler initialized
[ 2.854553] IR Sony protocol handler initialized
[ 2.855590] usb 1-1: new high-speed USB device number 2 using ehci-omap
[ 2.866668] IR RC5 (streamzap) protocol handler initialized
[ 2.872528] IR MCE Keyboard/mouse protocol handler initialized
[ 2.878662] IR LIRC bridge handler initialized
[ 2.883453] Linux video capture interface: v2.00
[ 2.889068] usbcore: registered new interface driver uvcvideo
[ 2.895263] USB Video Class driver (1.1.1)
[ 2.899902] Driver for 1-wire Dallas network protocol.
[ 2.907562] OMAP Watchdog Timer Rev 0x00: initial timeout 60 sec
[ 2.914764] cpuidle: using governor ladder
[ 2.919097] cpuidle: using governor menu
[ 2.934631] usbcore: registered new interface driver usbhid
[ 2.940521] usbhid: USB HID core driver
[ 2.946075] logger: created 256K log 'log_main'
[ 2.951232] logger: created 256K log 'log_events'
[ 2.956542] logger: created 256K log 'log_radio'
[ 2.961883] logger: created 256K log 'log_system'
[ 2.969360] usbcore: registered new interface driver snd-usb-audio
[ 2.978668] ALSA device list:
[ 2.982055] No soundcards found.
[ 2.985687] oprofile: hardware counters not available
[ 2.991027] oprofile: using timer interrupt.
[ 2.996002] TCP cubic registered
[ 2.999511] Initializing XFRM netlink socket
[ 3.004180] NET: Registered protocol family 17
[ 3.009094] NET: Registered protocol family 15
[ 3.013793] lib80211: common routines for IEEE802.11 drivers
[ 3.019866] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 1
[ 3.028015] Registering SWP/SWPB emulation handler
[ 3.035766] usb 1-1: New USB device found, idVendor=0424, idProduct=9514
[ 3.038940] omap_vc_i2c_init: I2C config for all channels must match.
[ 3.038970] omap_vc_i2c_init: I2C config for all channels must match.
[ 3.039825] Power Management for TI OMAP4.
[ 3.060852] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 3.069030] omapfb omapfb: no driver for display: dvi
[ 3.075958] hub 1-1:1.0: USB hub found
[ 3.080108] hub 1-1:1.0: 5 ports detected
[ 3.110382] omapdss DISPC error: SYNC_LOST on channel tv, restarting the output with video overlays disabled
[ 3.207092] omapdss DISPC error: timeout waiting for digit out to stop
[ 3.214263] Unimplemented SVD code 2
[ 3.218048] Unimplemented SVD code 22
[ 3.221893] Unimplemented SVD code 31
[ 3.277587] omap_hwmod: dss_hdmi: _wait_target_disable failed
[ 3.283691] omapdss DISPC error: SYNC_LOST on channel tv, restarting the output with video overlays disabled
[ 3.327423] mmc0: host does not support reading read-only switch. assuming write-enable.
[ 3.337890] mmc0: new high speed SDHC card at address b368
[ 3.346008] omap_hwmod: dss_dispc: _wait_target_disable failed
[ 3.352325] omapdss DISPC error: SYNC_LOST on channel tv, restarting the output with video overlays disabled
[ 3.379394] mmcblk0: mmc0:b368 USD 7.46 GiB
[ 3.384643] usb 1-1.1: new high-speed USB device number 3 using ehci-omap
[ 3.398468] mmcblk0: p1 p2 p3 p4 < p5 p6 >
[ 3.411834] omapdss DISPC error: SYNC_LOST on channel tv, restarting the output with video overlays disabled
[ 3.473846] omap_hwmod: dss_dispc: _wait_target_disable failed
[ 3.480316] omapdss DISPC error: SYNC_LOST on channel tv, restarting the output with video overlays disabled
[ 3.506225] regulator_init_complete: VANA: incomplete constraints, leaving on
[ 3.515167] regulator_init_complete: VDAC: incomplete constraints, leaving on
[ 3.526977] regulator_init_complete: VUSB: incomplete constraints, leaving on
[ 3.540252] twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
[ 3.550903] Freeing init memory: 328K
[ 3.575378] omap_hwmod: dss_hdmi: _wait_target_disable failed
[ 3.584259] omap_hwmod: dss_dispc: _wait_target_disable failed
[ 3.593078] omap_hwmod: dss_core: _wait_target_disable failed
[ 3.599273] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
[ 3.606597] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 3.618743] smsc95xx v1.0.4
[ 3.722442] smsc95xx 1-1.1:1.0: eth0: register 'smsc95xx' at usb-ehci-omap.0-1.1, smsc95xx USB 2.0 Ethernet, 96:87:01:5e:5a:48
[ 3.817077] usb 1-1.2: new low-speed USB device number 4 using ehci-omap
[ 3.868011] init: cannot open '/initlogo.rle'
[ 3.894287] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 3.945617] usb 1-1.2: New USB device found, idVendor=046d, idProduct=c019
[ 3.952911] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3.960601] usb 1-1.2: Product: USB Optical Mouse
[ 3.965606] usb 1-1.2: Manufacturer: Logitech
[ 3.977813] input: Logitech USB Optical Mouse as /devices/platform/usbhs-omap.0/ehci-omap.0/usb1/1-1/1-1.2/1-1.2:1.0/input/input0
[ 3.992706] generic-usb 0003:046D:C019.0001: input: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-ehci-omap.0-1.2/input0
[ 4.090118] usb 1-1.3: new low-speed USB device number 5 using ehci-omap
[ 4.223754] usb 1-1.3: New USB device found, idVendor=03f0, idProduct=0024
[ 4.231018] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 4.238739] usb 1-1.3: Product: HP Basic USB Keyboard
[ 4.244018] usb 1-1.3: Manufacturer: CHICONY
[ 4.257415] input: CHICONY HP Basic USB Keyboard as /devices/platform/usbhs-omap.0/ehci-omap.0/usb1/1-1/1-1.3/1-1.3:1.0/input/input1
[ 4.271209] generic-usb 0003:03F0:0024.0002: input: USB HID v1.10 Keyboard [CHICONY HP Basic USB Keyboard] on usb-ehci-omap.0-1.3/input0
[ 4.784729] EXT4-fs (mmcblk0p3): recovery complete
[ 4.792755] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null)
[ 6.659332] EXT4-fs (mmcblk0p5): recovery complete
[ 6.666870] EXT4-fs (mmcblk0p5): mounted filesystem with ordered data mode. Opts: (null)
[ 6.699218] android_usb: already disabled
[ 6.704254] adb_bind_config
[ 6.929260] init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery'
[ 7.154998] adb_bind_config
[ 7.358947] adb_open
root@android:/ # [ 7.434112] warning: `rild' uses 32-bit capabilities (legacy support in use)
[ 8.186614] omap_hwmod: dss_dispc: _wait_target_disable failed
[ 8.195465] omap_hwmod: dss_core: _wait_target_disable failed
[ 8.376342] omap_hwmod: dss_dispc: _wait_target_disable failed
[ 8.385162] omap_hwmod: dss_core: _wait_target_disable failed
[ 8.550537] omap_hwmod: dss_dispc: _wait_target_disable failed
[ 8.559387] omap_hwmod: dss_core: _wait_target_disable failed
[ 8.569610] omap_hwmod: dss_dispc: _wait_target_disable failed
[ 8.578399] omap_hwmod: dss_core: _wait_target_disable failed
[ 8.803253] omap_hwmod: dss_dispc: _wait_target_disable failed
[ 8.812164] omap_hwmod: dss_core: _wait_target_disable failed
[ 8.921478] omap_hwmod: dss_dispc: _wait_target_disable failed
[ 8.930267] omap_hwmod: dss_core: _wait_target_disable failed
[ 9.039245] omap_hwmod: dss_dispc: _wait_target_disable failed
[ 9.048095] omap_hwmod: dss_core: _wait_target_disable failed
[ 9.148468] omap_hwmod: dss_dispc: _wait_target_disable failed
[ 9.157348] omap_hwmod: dss_core: _wait_target_disable failed
[ 9.253509] omap_hwmod: dss_dispc: _wait_target_disable failed
[ 9.262298] omap_hwmod: dss_core: _wait_target_disable failed
[ 9.362152] omap_hwmod: dss_dispc: _wait_target_disable failed
[ 9.370971] omap_hwmod: dss_core: _wait_target_disable failed
[ 9.470947] omap_hwmod: dss_dispc: _wait_target_disable failed
[ 9.479766] omap_hwmod: dss_core: _wait_target_disable failed
[ 9.584930] omap_hwmod: dss_dispc: _wait_target_disable failed
[ 9.593749] omap_hwmod: dss_core: _wait_target_disable failed
[ 9.709777] omap_hwmod: dss_dispc: _wait_target_disable failed
[ 9.718627] omap_hwmod: dss_core: _wait_target_disable failed
[ 9.834747] omap_hwmod: dss_dispc: _wait_target_disable failed
[ 9.843597] omap_hwmod: dss_core: _wait_target_disable failed
[ 9.897125] omap_hwmod: dss_dispc: _wait_target_disable failed
[ 9.905944] omap_hwmod: dss_core: _wait_target_disable failed
[ 10.021820] omap_hwmod: dss_dispc: _wait_target_disable failed
[ 10.030670] omap_hwmod: dss_core: _wait_target_disable failed
[ 10.131439] omap_hwmod: dss_dispc: _wait_target_disable failed
...
...
...
[ 48.455261] omap_hwmod: dss_dispc: _wait_target_disable failed
[ 48.464111] omap_hwmod: dss_core: _wait_target_disable failed
[ 49.191558] omap_hwmod: dss_dispc: _wait_target_disable failed
[ 49.200622] omap_hwmod: dss_core: _wait_target_disable failed
[ 49.960754] omap_hwmod: dss_dispc: _wait_target_disable failed
[ 49.969635] omap_hwmod: dss_core: _wait_target_disable failed
[ 50.680358] omap_hwmod: dss_dispc: _wait_target_disable failed
[ 50.689147] omap_hwmod: dss_core: _wait_target_disable failed

[warmcat (andy-warmcat)]

Hm this seems to be tilt-android-tracking kernel (3.2-rc4) but nowadays we all moved to ICS it seems.

Is there any point keeping open bugs on old rootfs with tracking kernel that now supports ICS only?

[Abhishek Paliwal (abhishek-paliwal)]

Marking Gingerbread open bugs to "Won't fix" state (on Linaro-Android helpdesk) as fixes are done only on ICS track now.