Texas Instruments X-Loader 1.4.4ss (Mar 18 2011 - 14:14:59) Reading boot sector Loading u-boot.bin from mmc U-Boot 2011.06 (Jul 13 2011 - 15:17:23) CPU : OMAP4430 Board: OMAP4 Panda I2C: ready DRAM: 1 GiB MMC: OMAP SD/MMC: 0 Using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 3  2  1  0 reading boot.scr 401 bytes read Running bootscript from mmc0 ... ## Executing script at 82000000 reading uImage 4003236 bytes read reading uInitrd 171235 bytes read ## Booting kernel from Legacy Image at 80200000 ... Image Name: Linux-3.0.0-rc5-g2aced4d Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4003172 Bytes = 3.8 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 81600000 ... Image Name: Android Ramdisk Image Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 171171 Bytes = 167.2 KiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Linux version 3.0.0-rc5-g2aced4d (jenkins-build@ip-10-38-89-179) (gcc version 4.5.4 20110526 (prerelease) (Linaro GCC 4.5-2011.06-0) ) #1 SMP Wed Jul 13 16:06:20 UTC 2011 [ 0.000000] CPU: ARMv7 Processor [411fc092] revision 2 (ARMv7), cr=10c5387f [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: OMAP4 Panda board [ 0.000000] Reserving 50331648 bytes SDRAM for VRAM [ 0.000000] Memory policy: ECC disabled, Data cache writealloc [ 0.000000] Truncating RAM at a0000000-bfffffff to -afffffff (vmalloc region overlap). [ 0.000000] OMAP4430 ES2.1 [ 0.000000] SRAM: Mapped pa 0x40300000 to va 0xfe400000 size: 0xe000 [ 0.000000] PERCPU: Embedded 7 pages/cpu @c13b7000 s5984 r8192 d14496 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 180736 [ 0.000000] Kernel command line: console=tty0 console=ttyO2,115200n8 rootwait ro earlyprintk fixrtc nocompcache vram=48M omapfb.vram=0:24M,1:24M mem=456M@0x80000000 mem=512M@0xA0000000 init=/init androidboot.console=ttyO2 [ 0.000000] [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 456MB 464MB = 920MB total [ 0.000000] Memory: 708332k/708332k available, 20756k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB) [ 0.000000] vmalloc : 0xf0800000 - 0xf8000000 ( 120 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .init : 0xc0008000 - 0xc004c000 ( 272 kB) [ 0.000000] .text : 0xc004c000 - 0xc0768878 (7283 kB) [ 0.000000] .data : 0xc076a000 - 0xc07e59e0 ( 495 kB) [ 0.000000] .bss : 0xc07e5a04 - 0xc0da9b10 (5905 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:410 [ 0.000000] omap_hwmod: dpll_mpu_m2_ck: missing clockdomain for dpll_mpu_m2_ck. [ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] console [tty0] enabled [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.000000] ... MAX_LOCK_DEPTH: 48 [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 [ 0.000000] ... CLASSHASH_SIZE: 4096 [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.000000] ... CHAINHASH_SIZE: 16384 [ 0.000000] memory used by lock dependency info: 3695 kB [ 0.000000] per task-struct memory footprint: 1152 bytes [ 0.002014] Calibrating delay loop... 2007.19 BogoMIPS (lpj=7839744) [ 0.062561] pid_max: default: 32768 minimum: 301 [ 0.063140] Security Framework initialized [ 0.063446] Mount-cache hash table entries: 512 [ 0.066619] CPU: Testing write buffer coherency: ok [ 0.067382] Calibrating local timer... 491.91MHz. [ 0.109619] L310 cache controller enabled [ 0.109649] l2x0: 16 ways, CACHE_ID 0x410000c4, AUX_CTRL 0x7e470000, Cache size: 1048576 B [ 0.111785] CPU1: Booted secondary processor [ 0.111816] CPU1: Unknown IPI message 0x1 [ 0.140258] Brought up 2 CPUs [ 0.140289] SMP: Total of 2 processors activated (3963.96 BogoMIPS). [ 0.147827] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for emif_fw [ 0.147857] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l3_instr [ 0.147888] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l3_main_1 [ 0.147918] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l3_main_2 [ 0.147949] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_abe [ 0.147949] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_cfg [ 0.147979] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_per [ 0.148010] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_wkup [ 0.148010] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for mpu_private [ 0.148040] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for dsp [ 0.148071] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for ipu [ 0.148376] omap_hwmod: l3_div_ck: missing clockdomain for l3_div_ck. [ 0.163085] omap_hwmod: dss_dispc: softreset failed (waited 10000 usec) [ 0.175903] omap_hwmod: dss_rfbi: softreset failed (waited 10000 usec) [ 0.192077] omap_hwmod: ipu: failed to hardreset [ 0.196258] print_constraints: dummy: [ 0.196838] NET: Registered protocol family 16 [ 0.197387] GPMC revision 6.0 [ 0.200897] omap_device: omap_gpio.0: new worst case activate latency 0: 61035 [ 0.201934] OMAP GPIO hardware version 0.1 [ 0.202484] OMAP GPIO hardware version 0.1 [ 0.203033] OMAP GPIO hardware version 0.1 [ 0.203613] OMAP GPIO hardware version 0.1 [ 0.204162] OMAP GPIO hardware version 0.1 [ 0.204650] OMAP GPIO hardware version 0.1 [ 0.207733] omap_mux_init: Add partition: #1: core, flags: 2 [ 0.209106] omap_mux_init: Add partition: #2: wkup, flags: 2 [ 0.209259] error setting wl12xx data [ 0.212036] omap_device: omap_uart.1: new worst case deactivate latency 0: 30517 [ 0.212829] omap_device: omap_uart.3: new worst case activate latency 0: 30517 [ 0.217742] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers. [ 0.217773] hw-breakpoint: 1 breakpoint(s) reserved for watchpoint single-step. [ 0.217803] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.221984] pm_dbg_init: only OMAP3 supported [ 0.222229] OMAP DMA hardware revision 0.0 [ 0.252044] bio: create slab at 0 [ 0.253631] print_constraints: vwl1271: 1800 mV [ 0.255920] SCSI subsystem initialized [ 0.256195] omap_device: omap2_mcspi.1: new worst case activate latency 0: 30517 [ 0.259033] usbcore: registered new interface driver usbfs [ 0.259460] usbcore: registered new interface driver hub [ 0.259735] usbcore: registered new device driver usb [ 0.261657] omap_device: omap_i2c.1: new worst case activate latency 0: 30517 [ 0.269866] omap_i2c omap_i2c.1: bus 1 rev4.0 at 400 kHz [ 0.272033] Skipping twl internal clock init and using bootloader value (unknown osc rate) [ 0.272949] twl6030: PIH (irq 39) chaining IRQs 368..387 [ 0.274291] print_constraints: VUSB: 3300 mV normal standby [ 0.472534] twl6030_usb twl6030_usb: Initialized TWL6030 USB module [ 0.473693] print_constraints: VMMC: 1200 <--> 3000 mV at 3000 mV normal standby [ 0.474731] print_constraints: VPP: 1800 <--> 2500 mV at 1900 mV normal standby [ 0.475494] print_constraints: VCXIO: 1800 mV normal standby [ 0.476287] print_constraints: VDAC: 1800 mV normal standby [ 0.477172] print_constraints: VAUX2_6030: 1200 <--> 2800 mV at 1800 mV normal standby [ 0.478240] print_constraints: VAUX3_6030: 1000 <--> 3000 mV at 1200 mV normal standby [ 0.479003] print_constraints: CLK32KG: [ 0.479797] print_constraints: VANA: 2100 mV normal standby [ 0.490692] omap_i2c omap_i2c.2: bus 2 rev4.0 at 400 kHz [ 0.505920] omap_i2c omap_i2c.3: bus 3 rev4.0 at 100 kHz [ 0.521148] omap_i2c omap_i2c.4: bus 4 rev4.0 at 400 kHz [ 0.523010] Advanced Linux Sound Architecture Driver Version 1.0.24. [ 0.526672] Switching to clocksource 32k_counter [ 0.527069] cfg80211: Calling CRDA to update world regulatory domain [ 0.528808] Switched to NOHz mode on CPU #0 [ 0.530944] Switched to NOHz mode on CPU #1 [ 0.577331] musb-hdrc: version 6.0, pio, otg (peripheral+host) [ 0.577545] omap_device: musb-omap2430.-1: new worst case activate latency 0: 30517 [ 0.578033] musb-hdrc musb-hdrc: USB OTG mode controller at fc0ab000 using PIO, IRQ 124 [ 0.578613] omap_device: musb-omap2430.-1: new worst case deactivate latency 0: 30517 [ 0.578704] NET: Registered protocol family 2 [ 0.579040] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.580108] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.582214] TCP bind hash table entries: 65536 (order: 9, 2359296 bytes) [ 0.595001] TCP: Hash tables configured (established 131072 bind 65536) [ 0.595153] TCP reno registered [ 0.595184] UDP hash table entries: 512 (order: 3, 40960 bytes) [ 0.595428] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes) [ 0.596099] NET: Registered protocol family 1 [ 0.596557] Trying to unpack rootfs image as initramfs... [ 0.607238] Freeing initrd memory: 164K [ 0.607269] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.757629] ashmem: initialized [ 0.758087] VFS: Disk quotas dquot_6.5.2 [ 0.758239] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.759429] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.760375] Btrfs loaded [ 0.760437] msgmni has been set to 1383 [ 0.762451] io scheduler noop registered [ 0.762481] io scheduler deadline registered [ 0.762573] io scheduler cfq registered (default) [ 0.823852] OMAP DSS rev 4.0 [ 0.827026] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.933624] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 104) is a OMAP UART0 [ 0.956634] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 105) is a OMAP UART1 [ 0.980072] omap_uart.2: ttyO2 at MMIO 0x48020000 (irq = 106) is a OMAP UART2 [ 1.899017] console [ttyO2] enabled [ 1.925384] omap_uart.3: ttyO3 at MMIO 0x4806e000 (irq = 102) is a OMAP UART3 [ 1.969177] brd: module loaded [ 1.978546] loop: module loaded [ 1.984313] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.991180] omap2-nand driver initializing [ 1.995941] OneNAND driver initializing [ 2.003295] usbcore: registered new interface driver asix [ 2.009216] usbcore: registered new interface driver cdc_ether [ 2.015716] usbcore: registered new interface driver smsc75xx [ 2.022033] usbcore: registered new interface driver smsc95xx [ 2.028320] usbcore: registered new interface driver net1080 [ 2.034484] usbcore: registered new interface driver cdc_subset [ 2.040985] usbcore: registered new interface driver zaurus [ 2.046874] cdc_ncm: 01-June-2011 [ 2.050628] usbcore: registered new interface driver cdc_ncm [ 2.056884] usbcore: registered new interface driver usb8xxx [ 2.062866] libertas_sdio: Libertas SDIO driver [ 2.067626] libertas_sdio: Copyright Pierre Ossman [ 2.073577] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.080810] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller [ 2.088775] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1 [ 2.096954] ehci-omap ehci-omap.0: irq 109, io mem 0x4a064c00 [ 2.112915] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00 [ 2.119506] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.126678] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.134307] usb usb1: Product: OMAP-EHCI Host Controller [ 2.139923] usb usb1: Manufacturer: Linux 3.0.0-rc5-g2aced4d ehci_hcd [ 2.146697] usb usb1: SerialNumber: ehci-omap.0 [ 2.153472] hub 1-0:1.0: USB hub found [ 2.157531] hub 1-0:1.0: 3 ports detected [ 2.191406] usbcore: registered new interface driver cdc_wdm [ 2.197357] Initializing USB Mass Storage driver... [ 2.202819] usbcore: registered new interface driver usb-storage [ 2.209136] USB Mass Storage support registered. [ 2.214569] usbcore: registered new interface driver libusual [ 2.220855] usbcore: registered new interface driver usbtest [ 2.425903] android_usb gadget: Mass Storage Function, version: 2009/09/11 [ 2.433258] android_usb gadget: Number of LUNs=1 [ 2.438110] lun0: LUN: removable file: (no medium) [ 2.443847] android_usb gadget: android_usb ready [ 2.448852] musb-hdrc musb-hdrc: MUSB HDRC host driver [ 2.454864] musb-hdrc musb-hdrc: new USB bus registered, assigned bus number 2 [ 2.462646] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.469818] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.477447] usb usb2: Product: MUSB HDRC host driver [ 2.482696] usb usb2: Manufacturer: Linux 3.0.0-rc5-g2aced4d musb-hcd [ 2.489501] usb usb2: SerialNumber: musb-hdrc [ 2.495239] hub 2-0:1.0: USB hub found [ 2.499298] hub 2-0:1.0: 1 port detected [ 2.505065] mousedev: PS/2 mouse device common for all mice [ 2.514312] omap_device: omap_i2c.1: new worst case activate latency 0: 61035 [ 2.524291] using rtc device, twl_rtc, for alarms [ 2.529327] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0 [ 2.536193] twl_rtc twl_rtc: Power up reset detected. [ 2.542694] twl_rtc twl_rtc: Enabling TWL-RTC. [ 2.547943] i2c /dev entries driver [ 2.553558] Driver for 1-wire Dallas network protocol. [ 2.559814] omap_device: omap_wdt.-1: new worst case activate latency 0: 91552 [ 2.568328] OMAP Watchdog Timer Rev 0x00: initial timeout 60 sec [ 2.577606] omap_device: omap_i2c.1: new worst case deactivate latency 0: 30517 [ 2.590118] usbcore: registered new interface driver usbhid [ 2.595977] usbhid: USB HID core driver [ 2.600830] logger: created 64K log 'log_main' [ 2.605834] logger: created 256K log 'log_events' [ 2.611022] logger: created 64K log 'log_radio' [ 2.616119] logger: created 64K log 'log_system' [ 2.622863] usbcore: registered new interface driver snd-usb-audio [ 2.631469] ALSA device list: [ 2.634582] No soundcards found. [ 2.638183] oprofile: hardware counters not available [ 2.643493] oprofile: using timer interrupt. [ 2.648376] TCP cubic registered [ 2.651763] Initializing XFRM netlink socket [ 2.656372] usb 1-1: new high speed USB device number 2 using ehci-omap [ 2.656372] NET: Registered protocol family 17 [ 2.656524] NET: Registered protocol family 15 [ 2.656524] lib80211: common routines for IEEE802.11 drivers [ 2.656585] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 1 [ 2.686767] Registering SWP/SWPB emulation handler [ 2.697662] Power Management for TI OMAP4. [ 2.971527] usb 1-1: New USB device found, idVendor=0424, idProduct=9514 [ 2.978637] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 2.988098] hub 1-1:1.0: USB hub found [ 2.989196] omapdss DPI: Could not find exact pixel clock. Requested 23500 kHz, got 23630 kHz [ 2.991973] regulator_init_complete: VANA: incomplete constraints, leaving on [ 2.993408] regulator_init_complete: VDAC: incomplete constraints, leaving on [ 2.993743] regulator_init_complete: VCXIO: incomplete constraints, leaving on [ 2.994476] regulator_init_complete: VUSB: incomplete constraints, leaving on [ 3.031188] twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 3.039825] hub 1-1:1.0: 5 ports detected [ 3.045684] Freeing init memory: 272K [ 3.171661] mmc0: host does not support reading read-only switch. assuming write-enable. [ 3.191650] mmc0: new SDHC card at address 1234 [ 3.198944] mmcblk0: mmc0:1234 SA04G 3.68 GiB [ 3.212524] mmcblk0: p1 p2 p3 p4 < p5 p6 > [ 3.265747] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 3.295227] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null) [ 3.318939] EXT4-fs (mmcblk0p5): mounted filesystem with ordered data mode. Opts: (null) [ 3.332092] usb 1-1.1: new high speed USB device number 3 using ehci-omap [ 3.358123] init (1): /proc/1/oom_adj is deprecated, please use /proc/1/oom_score_adj instead. [ 3.437133] init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery' [ 3.451049] adb_open [ 3.459350] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00 [ 3.466888] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 3.478973] smsc95xx v1.0.4 # [ 3.667358] smsc95xx 1-1.1:1.0: eth0: register 'smsc95xx' at usb-ehci-omap.0-1.1, smsc95xx USB 2.0 Ethernet, 2e:f6:7d:44:9a:1b [ 3.768981] usb 1-1.2: new low speed USB device number 4 using ehci-omap [ 3.799987] warning: `rild' uses 32-bit capabilities (legacy support in use) [ 3.900604] usb 1-1.2: New USB device found, idVendor=045e, idProduct=0040 [ 3.907867] usb 1-1.2: New USB device strings: Mfr=1, Product=3, SerialNumber=0 [ 3.915771] usb 1-1.2: Product: Microsoft 3-Button Mouse with IntelliEye(TM) [ 3.923187] usb 1-1.2: Manufacturer: Microsoft [ 3.936004] input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /devices/platform/usbhs-omap.0/ehci-omap.0/usb1/1-1/1-1.2/1-1.2:1.0/input/input0 [ 3.952911] generic-usb 0003:045E:0040.0001: input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-ehci-omap.0-1.2/input0 [ 4.058502] usb 1-1.3: new low speed USB device number 5 using ehci-omap [ 4.212615] usb 1-1.3: New USB device found, idVendor=046d, idProduct=c315 [ 4.219909] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 4.227630] usb 1-1.3: Product: Logitech USB Keyboard [ 4.232971] usb 1-1.3: Manufacturer: Logitech [ 4.245208] input: Logitech Logitech USB Keyboard as /devices/platform/usbhs-omap.0/ehci-omap.0/usb1/1-1/1-1.3/1-1.3:1.0/input/input1 [ 4.259277] generic-usb 0003:046D:C315.0002: input: USB HID v1.10 Keyboard [Logitech Logitech USB Keyboard] on usb-ehci-omap.0-1.3/input0 [ 203.221801] PM: Syncing filesystems ... [ 215.579437] binder: release 1274:1274 transaction 2571 out, still active [ 215.586730] binder: release 1274:1294 transaction 2554 out, still active [ 215.593811] binder: release 1274:1295 transaction 2537 out, still active [ 215.600860] binder: release 1274:1296 transaction 2572 out, still active [ 231.809814] done. [ 231.818237] Freezing user space processes ... [ 231.824584] Freezing of user space aborted [ 231.829345] [ 231.830932] Restarting tasks ... [ 231.836883] done. [ 235.590789] binder: 1154:1167 transaction failed 29189, size 28-4 [ 235.597259] binder: send failed reply for transaction 2537, target dead [ 235.741271] binder: 1154:1166 transaction failed 29189, size 28-4 [ 235.747711] binder: send failed reply for transaction 2554, target dead [ 235.754699] binder: 1154:1297 transaction failed 29189, size 2372-0 [ 235.761322] binder: send failed reply for transaction 2571, target dead [ 235.769775] binder: 1154:1299 transaction failed 29189, size 28-4 [ 235.776184] binder: send failed reply for transaction 2572, target dead