If your printer is over the network and has an IP address to it. 

Run command 'hp-setup -i <IP address>'

For example if your device has an IP address 192.168.1.2,  then type  'hp-setup -i 192.168.1.2'







-------- Original message --------
From: peter mason <email address hidden> 
Date: 09/03/2015  5:27 PM  (GMT+05:30) 
To: <email address hidden> 
Subject: [Bug 1426110] Re: HPlip-3.15.2 make error 
 
1. make  clean

2. make

3. sudo make install

seems to have done a clean build.

However the only way to run Hplip is :

pi@raspberrypi ~/Desktop/hplip-3.15.2 $ hp-setup -i

HP Linux Imaging and Printing System (ver. 3.15.2)
Printer/Fax Setup Utility ver. 9.0

Copyright (c) 2001-15 Hewlett-Packard Development Company, LP
This software comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to distribute it
under certain conditions. See COPYING file for more details.

(Note: Defaults for each question are maked with a '*'. Press <enter> to
accept the default.)


--------------------------------
| SELECT CONNECTION (I/O) TYPE |
--------------------------------

  Num       Connection  Description                                               
            Type                                                                  
  --------  ----------  ----------------------------------------------------------
  0*        usb         Universal Serial Bus (USB)                                
  1         net         Network/Ethernet/Wireless (direct connection or JetDirect)

Enter number 0...1 for connection type (q=quit, enter=usb*) ? 1

Using connection type: net

error: No device selected/specified or that supports this functionality.
pi@raspberrypi ~/Desktop/hplip-3.15.2 $ hp-setup -i

HP Linux Imaging and Printing System (ver. 3.15.2)
Printer/Fax Setup Utility ver. 9.0

Copyright (c) 2001-15 Hewlett-Packard Development Company, LP
This software comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to distribute it
under certain conditions. See COPYING file for more details.

(Note: Defaults for each question are maked with a '*'. Press <enter> to
accept the default.)


--------------------------------
| SELECT CONNECTION (I/O) TYPE |
--------------------------------

  Num       Connection  Description                                               
            Type                                                                  
  --------  ----------  ----------------------------------------------------------
  0*        usb         Universal Serial Bus (USB)                                
  1         net         Network/Ethernet/Wireless (direct connection or JetDirect)

Enter number 0...1 for connection type (q=quit, enter=usb*) ? 0

Using connection type: usb

error: No device selected/specified or that supports this functionality.
pi@raspberrypi ~/Desktop/hplip-3.15.2 $

I can see the printer on the wifi monitor of Rpi.
The printer is HP Deskjet 3520, sitting 100`smm from the Raspberry Pi

-- 
You received this bug notification because you are a member of HP Linux
Imaging and Printing, which is subscribed to HPLIP.
Matching subscriptions: HP Linux Imaging and Printing, HP Linux Imaging and Printing, HP Linux Imaging and Printing, HPLIP
https://bugs.launchpad.net/bugs/1426110

Title:
  HPlip-3.15.2 make error

Status in HP Linux Imaging and Printing:
  New

Bug description:
  I did a manual install of the hplip-3.15.2.tar on a raspberryPi 2, but
  running make produces the following:

  pi@raspberrypi ~/Desktop/source/hplip-3.15.2.tar/hplip-3.15.2 $ make
  make: *** No targets specified and no makefile found.  Stop.
  pi@raspberrypi ~/Desktop/source/hplip-3.15.2.tar/hplip-3.15.2 $

  I also tried hplip-3.15.2.run but that failed to find PY3.

  Is it possible to install this software on RPi2?

To manage notifications about this bug go to:
https://bugs.launchpad.net/hplip/+bug/1426110/+subscriptions