Ubuntu
linux package

Stalled boot on Maverick with BeagleBoard

Bug #670211 reported by roman3017
6
This bug affects 1 person
Affects Status Importance Assigned to Milestone
linux (Ubuntu)
Expired
Undecided
Unassigned

Bug Description

I was not able to run Ubuntu 10.10 on my Beagleboard C4 following the instructions from https://wiki.ubuntu.com/ARM/OMAPMaverickInstall. Even after disconnecting all peripherals besides UART boot is freezing. The serial output is here:

40W

Texas Instruments X-Loader 1.4.4ss (Sep 30 2010 - 14:44:32)
Beagle Rev C4
Reading boot sector
Loading u-boot.bin from mmc

U-Boot 2010.09-rc1 (Sep 23 2010 - 11:20:00)

OMAP3530-GP ES3.1, CPU-OPP2, L3-165MHz, Max CPU Clock 720 mHz
OMAP3 Beagle board + LPDDR/NAND
I2C: ready
DRAM: 256 MiB
NAND: 256 MiB
*** Warning - bad CRC or NAND, using default environment

In: serial
Out: serial
Err: serial
Beagle Rev C4
Die ID #3c5200040000000004036abc08005014
Hit any key to stop autoboot: 0
mmc1 is available
reading boot.scr

323 bytes read
Running bootscript from mmc ...
## Executing script at 82000000
reading uImage

3687812 bytes read
reading uInitrd

6769443 bytes read
## Booting kernel from Legacy Image at 80000000 ...
   Image Name: Ubuntu Kernel
   Image Type: ARM Linux Kernel Image (uncompressed)
   Data Size: 3687748 Bytes = 3.5 MiB
   Load Address: 80008000
   Entry Point: 80008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 81600000 ...
   Image Name: Ubuntu Initrd
   Image Type: ARM Linux RAMDisk Image (gzip compressed)
   Data Size: 6769379 Bytes = 6.5 MiB
   Load Address: 00000000
   Entry Point: 00000000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.35-22-omap (buildd@gourd) (gcc version 4.4.5 (Ubuntu/Linaro 4.4.4-14ubuntu4) ) #33-Ubuntu Mon Sep 20 03:17:30 UTC 2010 (Ubuntu 2.6.35-22.33-omap 2.6.35.4)
[ 0.000000] CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c53c7f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine: OMAP3 Beagle Board
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 65536
[ 0.000000] free_area_init_node: node 0, pgdat c0763660, node_mem_map c0820000
[ 0.000000] Normal zone: 512 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 65024 pages, LIFO batch:15
[ 0.000000] OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp )
[ 0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000
[ 0.000000] Reserving 12582912 bytes SDRAM for VRAM
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: vram=12M omapfb.mode=dvi:1920x1080MR-16@60 root=/dev/mmcblk0p2 fixrtc console=ttyS2,115200n8 earlyprintk=ttyS2 loglevel=8
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] allocated 1310720 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Memory: 128MB 128MB = 256MB total
[ 0.000000] Memory: 231404k/231404k available, 30740k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
[ 0.000000] vmalloc : 0xd0800000 - 0xf8000000 ( 632 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .init : 0xc0008000 - 0xc0044000 ( 240 kB)
[ 0.000000] .text : 0xc0044000 - 0xc06ac000 (6560 kB)
[ 0.000000] .data : 0xc0718000 - 0xc0767960 ( 319 kB)
[ 0.000000] SLUB: Genslabs=9, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:402
[ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz
[ 0.000000] omap_hwmod: l3_hwmod: cannot be enabled (3)
[ 0.000000] omap_hwmod: l4_core_hwmod: cannot be enabled (3)
[ 0.000000] omap_hwmod: l4_per_hwmod: cannot be enabled (3)
[ 0.000000] omap_hwmod: l4_wkup_hwmod: cannot be enabled (3)
[ 0.000000] Reprogramming SDRC clock to 332000000 Hz
[ 0.000000] GPMC revision 5.0
[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
[ 0.000000] Total of 96 interrupts on 1 active controller
[ 0.000000] OMAP GPIO hardware version 2.5
[ 0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Calibrating delay loop... 504.17 BogoMIPS (lpj=1970176)
[ 0.000000] pid_max: default: 32768 minimum: 301
[ 0.000000] Security Framework initialized
[ 0.000000] AppArmor: AppArmor initialized
[ 0.000000] Yama: becoming mindful.
[ 0.000000] Mount-cache hash table entries: 512
[ 0.000000] Initializing cgroup subsys ns
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Initializing cgroup subsys memory
[ 0.000000] Initializing cgroup subsys devices
[ 0.000000] Initializing cgroup subsys freezer
[ 0.000000] CPU: Testing write buffer coherency: ok
[ 0.000000] devtmpfs: initialized
[ 0.000000] regulator: core version 0.5
[ 0.000000] NET: Registered protocol family 16
[ 0.000000] mux: Setting signal mcspi1_clk.gpio171 0x011c -> 0x011c
[ 0.000000] mux: Setting signal mcspi1_simo.gpio172 0x011c -> 0x011c
[ 0.000000] mux: Setting signal mcspi1_somi.gpio173 0x011c -> 0x011c
[ 0.000000] OMAP3 Beagle Rev: C4
[ 0.000000] mux: Setting signal i2c3_scl.i2c3_scl 0x0118 -> 0x0100
[ 0.000000] mux: Setting signal i2c3_sda.i2c3_sda 0x0118 -> 0x0100
[ 0.000000] mux: Setting signal etk_clk.hsusb1_stp 0x001b -> 0x0003
[ 0.000000] mux: Setting signal etk_ctl.hsusb1_clk 0x0013 -> 0x0003
[ 0.000000] mux: Setting signal etk_d8.hsusb1_dir 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal etk_d9.hsusb1_nxt 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal etk_d0.hsusb1_data0 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal etk_d1.hsusb1_data1 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal etk_d2.hsusb1_data2 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal etk_d7.hsusb1_data3 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal etk_d4.hsusb1_data4 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal etk_d5.hsusb1_data5 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal etk_d6.hsusb1_data6 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal etk_d3.hsusb1_data7 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal etk_d11.hsusb2_stp 0x0013 -> 0x0003
[ 0.000000] mux: Setting signal etk_d10.hsusb2_clk 0x0013 -> 0x0003
[ 0.000000] mux: Setting signal etk_d12.hsusb2_dir 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal etk_d13.hsusb2_nxt 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal etk_d14.hsusb2_data0 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal etk_d15.hsusb2_data1 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal mcspi1_cs3.hsusb2_data2 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal mcspi2_cs1.hsusb2_data3 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal mcspi2_simo.hsusb2_data4 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal mcspi2_somi.hsusb2_data5 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal mcspi2_cs0.hsusb2_data6 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal mcspi2_clk.hsusb2_data7 0x0113 -> 0x010b
[ 0.000000] Found NAND on CS0
[ 0.000000] Registering NAND on CS0
[ 0.000000] mux: Setting signal sdrc_cke0.sdrc_cke0 0x0118 -> 0x0000
[ 0.000000] mux: Setting signal sdrc_cke1.sdrc_cke1 0x0118 -> 0x0000
[ 0.000000] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available
[ 0.000122] OMAP DMA hardware revision 4.0
[ 0.010711] bio: create slab <bio-0> at 0
[ 0.017059] SCSI subsystem initialized
[ 0.021270] libata version 3.00 loaded.
[ 0.025909] usbcore: registered new interface driver usbfs
[ 0.031768] usbcore: registered new interface driver hub
[ 0.037506] usbcore: registered new device driver usb
[ 0.053375] i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz
[ 0.061798] twl4030: PIH (irq 7) chaining IRQs 368..375
[ 0.067291] twl4030: power (irq 373) chaining IRQs 376..383
[ 0.073608] twl4030: gpio (irq 368) chaining IRQs 384..401
[ 0.079742] mux: Setting signal etk_d9.gpio23 0x010b -> 0x0104
[ 0.085906] mux: Setting signal etk_d9.gpio23 0x0104 -> 0x011c
[ 0.092193] mux: Setting signal sdmmc1_clk.sdmmc1_clk 0x0018 -> 0x0118
[ 0.099182] mux: Setting signal sdmmc1_cmd.sdmmc1_cmd 0x0118 -> 0x0118
[ 0.106109] mux: Setting signal sdmmc1_dat0.sdmmc1_dat0 0x0118 -> 0x0118
[ 0.113250] mux: Setting signal sdmmc1_dat1.sdmmc1_dat1 0x0118 -> 0x0118
[ 0.120361] mux: Setting signal sdmmc1_dat2.sdmmc1_dat2 0x0118 -> 0x0118
[ 0.127471] mux: Setting signal sdmmc1_dat3.sdmmc1_dat3 0x0118 -> 0x0118
[ 0.134582] mux: Setting signal sdmmc1_dat4.sdmmc1_dat4 0x0118 -> 0x0118
[ 0.141693] mux: Setting signal sdmmc1_dat5.sdmmc1_dat5 0x0118 -> 0x0118
[ 0.148803] mux: Setting signal sdmmc1_dat6.sdmmc1_dat6 0x0118 -> 0x0118
[ 0.155914] mux: Setting signal sdmmc1_dat7.sdmmc1_dat7 0x0118 -> 0x0118
[ 0.164123] regulator: VUSB1V5: 1500 mV normal standby
[ 0.169891] regulator: VUSB1V8: 1800 mV normal standby
[ 0.175659] regulator: VUSB3V1: 3100 mV normal standby
[ 0.185089] twl4030_usb twl4030_usb: Initialized TWL4030 USB module
[ 0.192443] regulator: VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby
[ 0.199920] regulator: VDAC: 1800 mV normal standby
[ 0.205444] regulator: VPLL2: 1800 mV normal standby
[ 0.211181] regulator: VSIM: 1800 <--> 3000 mV at 1800 mV normal standby
[ 0.218414] i2c_omap i2c_omap.3: bus 3 rev3.12 at 100 kHz
[ 0.225158] Advanced Linux Sound Architecture Driver Version 1.0.23.
[ 0.232421] NetLabel: Initializing
[ 0.236053] NetLabel: domain hash size = 128
[ 0.240631] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.245941] NetLabel: unlabeled traffic allowed by default
[ 0.251831] Switching to clocksource 32k_counter
[ 0.267028] AppArmor: AppArmor Filesystem Enabled
[ 0.285247] musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0
[ 0.292816] musb_hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
[ 0.303802] musb_hdrc: MHDRC RTL version 1.400
[ 0.308563] musb_hdrc: setup fifo_mode 4
[ 0.312744] musb_hdrc: 28/31 max ep, 16384/16384 memory
[ 0.318450] musb_hdrc musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92
[ 0.326965] NET: Registered protocol family 2
[ 0.331878] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.340026] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.347625] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.354522] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.361175] TCP reno registered
[ 0.364501] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.370635] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.377471] NET: Registered protocol family 1
[ 0.383087] PMU: registered new PMU device of type 0
[ 0.388366] NetWinder Floating Point Emulator V0.97 (double precision)
[ 0.395599] Trying to unpack rootfs image as initramfs...
[ 0.413879] audit: initializing netlink socket (disabled)
[ 0.419616] type=2000 audit(0.890:1): initialized
[ 8.484893] VFS: Disk quotas dquot_6.5.2
[ 8.489440] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 8.500518] fuse init (API version 7.14)
[ 8.505371] msgmni has been set to 451
[ 8.511383] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 8.519165] io scheduler noop registered
[ 8.523345] io scheduler deadline registered
[ 8.527984] io scheduler cfq registered (default)
[ 8.593017] OMAP DSS rev 2.0
[ 8.596191] OMAP DISPC rev 3.0
[ 8.599456] OMAP VENC rev 2
[ 8.720428] Freeing initrd memory: 6608K
[ 8.945800] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 8.974212] serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
[ 9.002227] serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
[ 9.030212] serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
[ 9.037384] console [ttyS2] enabled, bootconsole disabled
[ 9.037384] console [ttyS2] enabled, bootconsole disabled
[ 9.057312] brd: module loaded
[ 9.064880] loop: module loaded
[ 9.070098] omap2-nand driver initializing
[ 9.074523] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron omap2-nand.0)
[ 9.082275] NAND bus width 8 instead 16 bit
[ 9.086517] No NAND device found.
[ 9.090026] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB 1,8V 16-bit)
[ 9.098724] Creating 5 MTD partitions on "omap2-nand.0":
[ 9.104125] 0x000000000000-0x000000080000 : "X-Loader"
[ 9.111022] 0x000000080000-0x000000260000 : "U-Boot"
[ 9.118255] 0x000000260000-0x000000280000 : "U-Boot Env"
[ 9.125000] 0x000000280000-0x000000680000 : "Kernel"
[ 9.132995] 0x000000680000-0x000010000000 : "File System"
[ 9.246185] Fixed MDIO Bus: probed
[ 9.250061] PPP generic driver version 2.4.2
[ 9.254730] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
[ 9.264495] CSLIP: code copyright 1989 Regents of the University of California.
[ 9.271850] SLIP linefill/keepalive option.
[ 9.276336] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 9.283233] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
[ 9.289031] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
[ 9.296691] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
[ 9.311584] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
[ 9.318298] hub 1-0:1.0: USB hub found
[ 9.322174] hub 1-0:1.0: 3 ports detected
[ 9.350860] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 9.357727] mice: PS/2 mouse device common for all mice
[ 9.363708] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
[ 9.370025] twl_rtc twl_rtc: Power up reset detected.
[ 9.376068] twl_rtc twl_rtc: Enabling TWL-RTC.
[ 9.381866] device-mapper: uevent: version 1.0.3
[ 9.387390] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: <email address hidden>
[ 9.396270] device-mapper: multipath: version 1.1.1 loaded
[ 9.401855] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 9.409362] cpuidle: using governor ladder
[ 9.413574] cpuidle: using governor menu
[ 9.417602] sdhci: Secure Digital Host Controller Interface driver
[ 9.423858] sdhci: Copyright(c) Pierre Ossman
[ 9.606231] No device for DAI omap-mcbsp-dai-0
[ 9.610748] No device for DAI omap-mcbsp-dai-1
[ 9.615234] No device for DAI omap-mcbsp-dai-2
[ 9.619720] No device for DAI omap-mcbsp-dai-3
[ 9.624237] No device for DAI omap-mcbsp-dai-4
[ 9.628692] Not OMAP3 EVM!
[ 9.631439] OMAP3 Beagle/Devkit8000 SoC init
[ 9.637481] asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok
[ 9.646972] ALSA device list:
[ 9.650054] #0: omap3beagle (twl4030)
[ 9.655334] TCP cubic registered
[ 9.659881] NET: Registered protocol family 10
[ 9.665985] lo: Disabled Privacy Extensions
[ 9.671539] NET: Registered protocol family 17
[ 9.677734] Power Management for TI OMAP3.
[ 9.682800] Disabling unused clock "sr2_fck"
[ 9.687164] Disabling unused clock "sr1_fck"
[ 9.691467] Disabling unused clock "mcbsp4_fck"
[ 9.696075] Disabling unused clock "mcbsp3_fck"
[ 9.700622] Disabling unused clock "mcbsp2_fck"
[ 9.705230] Disabling unused clock "mcbsp4_ick"
[ 9.709808] Disabling unused clock "mcbsp3_ick"
[ 9.714385] Disabling unused clock "mcbsp2_ick"
[ 9.718994] Disabling unused clock "gpt2_ick"
[ 9.723358] Disabling unused clock "gpt3_ick"
[ 9.727783] Disabling unused clock "gpt4_ick"
[ 9.732177] Disabling unused clock "gpt5_ick"
[ 9.736572] Disabling unused clock "gpt6_ick"
[ 9.740966] Disabling unused clock "gpt7_ick"
[ 9.745391] Disabling unused clock "gpt8_ick"
[ 9.749786] Disabling unused clock "gpt9_ick"
[ 9.754180] Disabling unused clock "wdt3_ick"
[ 9.758605] Disabling unused clock "wdt3_fck"
[ 9.763000] Disabling unused clock "gpio2_dbck"
[ 9.767578] Disabling unused clock "gpio3_dbck"
[ 9.772155] Disabling unused clock "gpio4_dbck"
[ 9.776733] Disabling unused clock "gpio5_dbck"
[ 9.781311] Disabling unused clock "gpio6_dbck"
[ 9.785888] Disabling unused clock "gpt9_fck"
[ 9.790313] Disabling unused clock "gpt8_fck"
[ 9.794677] Disabling unused clock "gpt7_fck"
[ 9.799102] Disabling unused clock "gpt6_fck"
[ 9.803497] Disabling unused clock "gpt5_fck"
[ 9.807891] Disabling unused clock "gpt4_fck"
[ 9.812316] Disabling unused clock "gpt3_fck"
[ 9.816711] Disabling unused clock "gpt2_fck"
[ 9.821105] Disabling unused clock "gpt1_ick"
[ 9.825500] Disabling unused clock "wdt1_ick"
[ 9.829925] Disabling unused clock "wdt2_ick"
[ 9.834320] Disabling unused clock "wdt2_fck"
[ 9.838714] Disabling unused clock "gpio1_dbck"
[ 9.843322] Disabling unused clock "gpt1_fck"
[ 9.847717] Disabling unused clock "cam_ick"
[ 9.852050] Disabling unused clock "cam_mclk"
[ 9.856475] Disabling unused clock "des1_ick"
[ 9.860870] Disabling unused clock "sha11_ick"
[ 9.865356] Disabling unused clock "rng_ick"
[ 9.869689] Disabling unused clock "aes1_ick"
[ 9.874084] Disabling unused clock "ssi_ick"
[ 9.878387] Disabling unused clock "mailboxes_ick"
[ 9.883239] Disabling unused clock "mcbsp1_ick"
[ 9.887817] Disabling unused clock "mcbsp5_ick"
[ 9.892395] Disabling unused clock "gpt10_ick"
[ 9.896881] Disabling unused clock "gpt11_ick"
[ 9.901367] Disabling unused clock "i2c2_ick"
[ 9.905792] Disabling unused clock "mcspi1_ick"
[ 9.910339] Disabling unused clock "mcspi2_ick"
[ 9.914947] Disabling unused clock "mcspi3_ick"
[ 9.919494] Disabling unused clock "mcspi4_ick"
[ 9.924102] Disabling unused clock "hdq_ick"
[ 9.928405] Disabling unused clock "mspro_ick"
[ 9.932891] Disabling unused clock "des2_ick"
[ 9.937316] Disabling unused clock "sha12_ick"
[ 9.941772] Disabling unused clock "aes2_ick"
[ 9.946197] Disabling unused clock "icr_ick"
[ 9.950500] Disabling unused clock "pka_ick"
[ 9.954833] Disabling unused clock "ssi_ssr_fck"
[ 9.959472] Disabling unused clock "hdq_fck"
[ 9.963806] Disabling unused clock "mcspi1_fck"
[ 9.968383] Disabling unused clock "mcspi2_fck"
[ 9.972961] Disabling unused clock "mcspi3_fck"
[ 9.977539] Disabling unused clock "mcspi4_fck"
[ 9.982086] Disabling unused clock "mcbsp1_fck"
[ 9.986694] Disabling unused clock "mcbsp5_fck"
[ 9.991271] Disabling unused clock "i2c2_fck"
[ 9.995666] Disabling unused clock "mspro_fck"
[ 10.000152] Disabling unused clock "gpt11_fck"
[ 10.004638] Disabling unused clock "gpt10_fck"
[ 10.009155] Disabling unused clock "sad2d_ick"
[ 10.013641] Disabling unused clock "dpll4_m6x2_ck"
[ 10.018493] Disabling unused clock "dpll3_m3x2_ck"
[ 10.023345] Disabling unused clock "sys_clkout1"
[ 10.028015] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
[ 10.040039] registered taskstats version 1
[ 10.044403] fbcvt: 1920x1080@60: CVT Name - 2.073M9-R
[ 10.103881] Console: switching to colour frame buffer device 240x67
[ 10.141540] regulator_init_complete: incomplete constraints, leaving VDAC on
[ 10.149658] twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
[ 10.159729] Freeing init memory: 240K
[ 10.163574] mmc0: new high speed SDHC card at address 0001
[ 10.176818] mmcblk0: mmc0:0001 00000 3.79 GiB
[ 10.188049] mmcblk0: p1 p2
Loading, please wait...
[ 10.349700] udev[68]: starting version 163
Begin: Loading essential drivers ... [ 12.267150] Btrfs loaded
done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... [ 13.679870] mmcblk0: p1 p2
Resizing root filesystem. Please wait, this will take a moment ...
[ 16.614807] EXT3-fs: barriers not enabled
[ 16.620178] kjournald starting. Commit interval 5 seconds
[ 16.633178] EXT3-fs (mmcblk0p2): using internal journal
[ 16.638458] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode
Checking filesystem before resizing... Done.
Resizing, pass: 1 [100/100]
done.
[ 54.814147] EXT3-fs: barriers not enabled
[ 54.819305] kjournald starting. Commit interval 5 seconds
[ 54.825042] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode
Begin: Running /scripts/local-bottom ... [ 55.156494] EXT3-fs (mmcblk0p2): using internal journal
detected console= cmdline option, enabling serial console handling
setting up fstab
setting up swap, this will take a moment ...
setting up loopback networking
enabling oem-config
writing flash-kernel.conf
creating boot.script
adding SD card optimizations
setting default session
reboot check
Rebooting into configuration session ...
[ 146.240020] md: stopping all md devices.
[ 147.267761] Restarting system.
40W

Texas Instruments X-Loader 1.4.4ss (Sep 30 2010 - 14:44:32)
Beagle Rev C4
Reading boot sector
Loading u-boot.bin from mmc

U-Boot 2010.09-rc1 (Sep 23 2010 - 11:20:00)

OMAP3530-GP ES3.1, CPU-OPP2, L3-165MHz, Max CPU Clock 720 mHz
OMAP3 Beagle board + LPDDR/NAND
I2C: ready
DRAM: 256 MiB
NAND: 256 MiB
*** Warning - bad CRC or NAND, using default environment

In: serial
Out: serial
Err: serial
Beagle Rev C4
Die ID #3c5200040000000004036abc08005014
Hit any key to stop autoboot: 0
mmc1 is available
reading boot.scr

367 bytes read
Running bootscript from mmc ...
## Executing script at 82000000
reading uImage

3687812 bytes read
reading uInitrd

6769443 bytes read
## Booting kernel from Legacy Image at 80000000 ...
   Image Name: Ubuntu Kernel
   Image Type: ARM Linux Kernel Image (uncompressed)
   Data Size: 3687748 Bytes = 3.5 MiB
   Load Address: 80008000
   Entry Point: 80008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 81600000 ...
   Image Name: Ubuntu Initrd
   Image Type: ARM Linux RAMDisk Image (gzip compressed)
   Data Size: 6769379 Bytes = 6.5 MiB
   Load Address: 00000000
   Entry Point: 00000000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
fsck from util-linux-ng 2.17.2
/dev/mmcblk0p2: clean, 118171/462240 files, 534028/975948 blocks
 * Starting AppArmor profiles Skipping profile in /etc/apparmor.d/disable: usr.bin.firefox
                                                                         [ OK ]
 * Setting sensors limits [ OK ]
speech-dispatcher disabled; edit /etc/default/speech-dispatcher
fsck from util-linux-ng 2.17.2
/dev/mmcblk0p2: clean, 118171/462240 files, 534028/975948 blocks
 * Starting AppArmor profiles Skipping profile in /etc/apparmor.d/disable: usr.bin.firefox
                                                                         [ OK ]
 * Setting sensors limits [ OK ]
 * PulseAudio configured for per-user sessions
saned disabled; edit /etc/default/saned
 * Enabling additional executable binary formats binfmt-support [ OK ]

Revision history for this message
Jeremy Foshee (jeremyfoshee) wrote :

Hi roman,

This bug was reported a while ago and there hasn't been any activity in it recently. We were wondering if this is still an issue? Can you try with the latest development release of Ubuntu? ISO CD images are available from http://cdimage.ubuntu.com/releases/ .

If it remains an issue, could you run the following command from a Terminal (Applications->Accessories->Terminal). It will automatically gather and attach updated debug information to this report.

apport-collect -p linux 670211

Also, if you could test the latest upstream kernel available that would be great. It will allow additional upstream developers to examine the issue. Refer to https://wiki.ubuntu.com/KernelMainlineBuilds . Once you've tested the upstream kernel, please remove the 'needs-upstream-testing' tag. This can be done by clicking on the yellow pencil icon next to the tag located at the bottom of the bug description and deleting the 'needs-upstream-testing' text. Please let us know your results.

Thanks in advance.

    [This is an automated message. Apologies if it has reached you inappropriately; please just reply to this message indicating so.]

tags: added: needs-kernel-logs
tags: added: needs-upstream-testing
tags: added: kj-triage
Changed in linux (Ubuntu):
status: New → Incomplete
Revision history for this message
Launchpad Janitor (janitor) wrote :

[Expired for linux (Ubuntu) because there has been no activity for 60 days.]

Changed in linux (Ubuntu):
status: Incomplete → Expired
To post a comment you must log in.
This report contains Public information  
Everyone can see this information.
Subscribing...

Other bug subscribers

Remote bug watches

Bug watches keep track of this bug in other bug trackers.