Nautilus Sony PRS-300 connected via usb cable

[eeexception]

Binary package hint: nautilus

So I'm trying to connect my e-book reader to the laptop with Ubuntu 10.04 alpha3. After connecting I could see
[ 614.924184] usb 1-1: new high speed USB device using ehci_hcd and address 9
[ 615.058939] usb 1-1: configuration #1 chosen from 2 choices
[ 615.064437] scsi9 : SCSI emulation for USB Mass Storage devices
[ 615.065400] usb-storage: device found at 9
[ 615.065414] usb-storage: waiting for device to settle before scanning
[ 620.064543] usb-storage: device scan complete
[ 620.065402] scsi 9:0:0:0: Direct-Access Sony PRS-300 1000 PQ: 0 ANSI: 2
[ 620.065995] scsi 9:0:0:1: Direct-Access Sony PRS-300 Launcher 1000 PQ: 0 ANSI: 2
[ 620.072858] sd 9:0:0:0: [sdc] 908544 512-byte logical blocks: (465 MB/443 MiB)
[ 620.091168] sd 9:0:0:0: Attached scsi generic sg2 type 0
[ 620.093683] sd 9:0:0:1: Attached scsi generic sg3 type 0
[ 620.171424] sd 9:0:0:0: [sdc] Write Protect is off
[ 620.171448] sd 9:0:0:0: [sdc] Mode Sense: 0f 00 00 00
[ 620.171462] sd 9:0:0:0: [sdc] Assuming drive cache: write through
[ 620.175418] sd 9:0:0:1: [sdd] 20480 512-byte logical blocks: (10.4 MB/10.0 MiB)
[ 620.271480] sd 9:0:0:1: [sdd] Write Protect is on
[ 620.271503] sd 9:0:0:1: [sdd] Mode Sense: 0f 00 80 00
[ 620.271518] sd 9:0:0:1: [sdd] Assuming drive cache: write through
[ 620.371546] sd 9:0:0:0: [sdc] Assuming drive cache: write through
[ 620.371577] sdc:
[ 620.481747] sd 9:0:0:1: [sdd] Assuming drive cache: write through
[ 620.481771] sdd:
[ 620.581658] sd 9:0:0:0: [sdc] Assuming drive cache: write through
[ 620.581681] sd 9:0:0:0: [sdc] Attached SCSI removable disk
[ 620.691799] sd 9:0:0:1: [sdd] Assuming drive cache: write through
[ 620.691819] sd 9:0:0:1: [sdd] Attached SCSI removable disk

in dmesg output
and I see the device in lsusb, but could not see any attached disks in nautilus.
By the way Sony Prs-300 determed as two removamble flash drives in Ubuntu Karmic.

[eeexception (eeexception)]

So I see disks in fdisk -l output and can mount them manually, but do not understand why this does not work automatically.

[eeexception (eeexception)]

The problem is in udev rules or device kit rules, so the same problem with all devices which were starting using hal service.

[Pedro Villavicencio (pedro)]

so not a nautilus issue, reassigning.

[Bluppie (benhyper)]

I can see my READER as an hardisk but it is not recognized as an sony PRS-300. So Calbre can´t update my ebooks to it.
I use now 10.04 LTS - Lucid Lynx. Before I used 9.10 with no problems.