hirsute/linux-raspi: Upstream raspberrypi patchset 2021-01-23

[Juerg Haefliger]

Upstream raspberrypi patchset 2021-01-23

   Ported from the following raspberrypi branch:
      rpi-5.11.y

from https://github.com/raspberrypi/linux.git

configs: Add CRYPTO_ADIANTUM=m
configs: Regenerate defconfigs
configs: Add NVMEM_RMEM=m for 2711
ARM: multi_v7_defconfig: Enable nvmem's rmem driver
arm64: defconfig: Enable nvmem's rmem driver
ARM: dts: bcm2711: Add reserved memory template to hold firmware configuration
nvmem: Add driver to expose reserved memory as nvmem
dt-bindings: nvmem: Add bindings for rmem driver
configs: Add CONFIG_USB_NET_AQC111=m
configs: Add CONFIG_NETFILTER_XT_MATCH_PHYSDEV=m
staging: vc04_services: ISP: Add colour denoise control
uapi: bcm2835-isp: Add colour denoise configuration
bcm2835-dma: Add bcm2835-dma: Add DMA_WIDE_SOURCE and DMA_WIDE_DEST flags
dt: Enable DMA_WIDE_SOURCE and DMA_WIDE_DEST for hdmi audio
configs: Enable BCM2835 thermal driver in kernel8
vc4: Correct POS1_SCL for hvs5
vc4: Correct lbm size and calculation
overlays: seeed-can-fd-hat: clarify how to identify HAT version
dtoverlays: Update sensor overlays to use cam1_reg where possible
dt: Add a camera regulator node to all downstream Pi platforms
arch/arm: Add __memset alias to memset_rpi.S
overlays: add spi override to merus-amp overlay
overlays: add wm8960-soundcard overlay
overlays: Add overlay for Seeed Studio CAN BUS FD HAT v1 (based on mcp2517fd)
overlays: give Seeed Studio CAN BUS FD HAT a -v2 postfix
media: i2c: ov5647: Selection compliance fixes
bcm2711-rpi.dtsi: Bump hdmi audio dma priority to max
bcm2835-dma: Avoid losing CS flags after interrupt
dts: Enable DMA_WIDE_SOURCE for hdmi audio dma
staging/bcm2835-isp: Log the number of excess supported formats
staging/bcm2835-isp: Add the unpacked (16bpp) raw formats
staging/bcm2835-codec: Log the number of excess supported formats
staging/bcm2835-codec: Add the unpacked (16bpp) raw formats
staging/vc04_services: Add additional unpacked raw formats
staging/mmal-vchiq: Fix incorrect static vchiq_instance.
staging: vchiq: Fix bulk transfers on 64-bit builds
vc-sm-cma: fixed kbuild problem
staging: vchiq: Fix bulk userdata handling
drm/vc4: hdmi: Enable 10/12 bpc output
drm/vc4: hdmi: Limit the BCM2711 to the max without scrambling
drm/vc4: hdmi: Use the connector state pixel rate for the PHY
drm/vc4: hdmi: Store pixel frequency in the connector state
drm/vc4: hdmi: Create a custom connector state
drm/vc4: hdmi: Don't access the connector state in reset if kmalloc fails
drm/vc4: hdmi: Take into account the clock doubling flag in atomic_check
drm/vc4: Pass the atomic state to encoder hooks
drm/vc4: hvs: Align the HVS atomic hooks to the new API
drm/atomic: Pass the full state to CRTC atomic enable/disable
media: i2c: imx477: Selection compliance fixes
drm/vc4: Correct DSI register definition
vc4_hdmi: Move hdmi reset to bind
drm/vc4: Add configuration for BCM2711 DSI1.
dt-bindings: Add compatible for BCM2711 DSI1
drm/vc4: Add support for DSI0
media: ov9281: Add 1280x720 and 640x480 modes
drm/panel/raspberrypi-ts: Insert delay before polling for startup state
drm/panel/raspberrypi-touchscreen: Use independent I2C actions with delay.
Input: edt-ft5x06: Poll the device if no interrupt is configured.
vc4: Clear unused infoframe packet RAM registers
PCI: brcmstb: Restore initial fundamental reset
vc4_hdmi: Report that 3d/stereo is allowed
phy: broadcom: Add bcm54213pe configuration
phy: broadcom: split out the BCM54213PE from the BCM54210E IDs
firmware: raspberrypi: Add support for tryonce reboot flag
watchdog: bcm2835: Ignore params after the partition number
bcm2835-pcm: Fix up multichannel pcm audio
PiFi-40 driver, Makefile and Kconfig
bcm2708_fb: Fix a build warning
rpivid_h625: Fix build warnings
gpio-fsm: Fix a build warning
dwc_otg: Minimise header and fix build warnings
rpisense-fb: Set pseudo_pallete to prevent crash on fbcon takeover
staging: bcm2835-audio: Add disable-headphones flag
xhci: quirks: add link TRB quirk for VL805
drm/vc4: Add the 2711 HVS as a suitable DMA node
drm/vc4: Add all the HDMI registers into the debugfs dumps
drm/vc4: Reading the hotplug register is only valid if no GPIO defined
gpio: Add gpio-fsm driver
staging: vc04_services: ISP: Add a more complex ISP processing component
uapi: bcm2835-isp: Add bcm2835-isp uapi header file
bcm2835-dma: only reserve channel 0 if legacy dma driver is enabled
staging: vc04_services: Add a V4L2 M2M codec driver
staging: mmal-vchiq: Use vc-sm-cma to support zero copy
staging: mmal-vchiq: Add monochrome image formats
staging: vchiq-mmal: Add support for 14bit Bayer
staging: vc04_services: Add new vc-sm-cma driver
staging: bcm2835-camera: Replace deprecated V4L2_PIX_FMT_BGR32
dwc_otg: initialise sched_frame for periodic QHs that were parked
USB: gadget: f_hid: avoid crashes and log spam
char: Add broadcom char drivers back to build files
net: bcmgenet: Reset RBUF on first open
rpivid_h265: Fix width/height typo
brcmfmac: Increase power saving delay to 2s
staging/fbtft: Add support for display variants
media: i2c: imx477: Parse and register properties
media: i2c: imx477: Return correct result on sensor id verification
media: i2c: imx477: Add support for adaptive frame control
media: i2c: Add driver for Sony IMX477 sensor
drm/vc4: Add FKMS as an acceptable node for dma ranges.
drm/vc4: Add firmware-kms mode
drm/vc4: Add support for YUV color encodings and ranges
drm/vc4: Add support for DRM_FORMAT_P030 to vc4 planes
vc4: cec: Restore cec physical address on reconnect
vc4: Report channel mapping back to userspace
vc_hdmi: Set VC4_HDMI_MAI_CONFIG_FORMAT_REVERSE
vc4_hdmi: Remove firmware logic for MAI threshold setting
drm/vc4: enable HBR MAI format on HBR streams
drm/vc4: move setup from hw_params to prepare
drm/vc4: add iec958 controls to vc4_hdmi
vc4_hdmi: Set HDMI_MAI_FMT
vc4_hdmi: Set HD_CTL_WHOLSMP and HD_CTL_CHALIGN_SET
drm/vc4: Adopt the dma configuration from the HVS or V3D component
vc4_hdmi: Remove cec_available flag as always supported
vc4_hdmi: Adjust CEC ref clock based on its input clock
vc4_hdmi: Make irq shared
vc4_hdmi_regs: Make interrupt mask variant specific
vc4_hdmi_regs: Add Intr2 register block
vc4_hdmi: Fix up CEC registers
vc4_hdmi: Fix register offset when sending longer CEC messages
vc4_hdmi: BCM2835 requires a fixed hsm clock for CEC to work
vc4: Set driver_name for card
include/firmware: Add enum for RPI_FIRMWARE_FRAMEBUFFER_GET_DISPLAY_ID
vchiq_2835_arm: Implement a DMA pool for small bulk transfers (#2699)
dwc_otg: whitelist_table is now productlist_table
bcm2835-mmc: uninitialized_var is no more
media: i2c: ov9281: Add support for 8 bit readout
media: i2c: tc358743: Only allow supported pixel fmts in set_fmt
media: bcm2835-unicam: Drop WARN on uing direct cache alias
staging: media: rpivid: Select MEDIA_CONTROLLER and MEDIA_CONTROLLER_REQUEST_API
media: bcm2835: unicam: Select MEDIA_CONTROLLER and VIDEO_V4L2_SUBDEV_API
ARM: proc-v7: Force misalignment of early stmia
bcm2835-dma: Advertise the full DMA range
staging: vchiq_arm: children inherit DMA config
leds: Add the actpwr trigger
media: i2c: ov5647: Parse and register properties
dt-bindings: bcm2835-unicam: Update documentation with new clock params
media: bcm2835: unicam: Set VPU min clock freq to 250Mhz.
media: bcm2835-unicam: Ensure type is VIDEO_CAPTURE in [g|s]_selection
media: bcm2835-unicam: Reinstate V4L2_CAP_READWRITE in the caps
media: i2c: imx290: Set the colorspace fields in the format
media: i2c: imx290: Add support for g_selection to report cropping
media: i2c: imx290: Explicitly set v&h blank on mode change
media: i2c: ov9281: Read chip ID via 2 reads
media: i2c: ov9281: Fixup for recent kernel releases, and remove custom code
media: i2c: ov9281: add enum_frame_interval function for iq tool 2.2 and hal3
media: i2c: ov9281: fix mclk issue when probe multiple camera.
media: i2c: add ov9281 driver.
bcm2835-dma: Add NO_WAIT_RESP flag
media: bcm2835-unicam: Add support for unpacked 14bit Bayer formats
media: bcm2835-unicam: Add support for 14bit mono sources
media: bcm2835-unicam: Add support for 12bit mono packed format
media: Add a pixel format for MIPI packed 14bit luma only.
media: Add a pixel format for MIPI packed 12bit luma only.
serial: 8250: bcm2835aux - defer if clock is zero
media: i2c: imx290: Switch set_hmax to use imx290_write_buffered_reg
media : i2c: imx290: Add support for the mono sensor variant.
media: dt-bindings: media: i2c: Add mono version to IMX290 bindings
media: i2c: imx290: Add H and V flip controls
media: i2c: imx290: Add exposure control to the driver.
media: i2c: imx290: Add support for V4L2_CID_VBLANK
media: i2c: imx290: Convert HMAX setting into V4L2_CID_HBLANK
media: i2c: imx290: Correct range for V4L2_CID_GAIN to 0-238
media: i2c: imx290: Add support for 74.25MHz clock
media: i2c: imx290: set the format before VIDIOC_SUBDEV_G_FMT is called
media: bcm2835-unicam: Avoid gcc warning over {0} on endpoint
media: bcm2835-unicam: Add support for get_mbus_config to set num lanes
media: bcm2835-unicam: Driver for CCP2/CSI2 camera interface
brcmfmac: Prefer a ccode from OTP over nvram file
staging: bcm2835-audio: Add missing MODULE_ALIAS
media: irs1125: Keep HW in sync after imager reset
media: irs1125: Atomic access to imager reconfiguration
media: irs1125: Refactoring and debug messages
media: irs1125: Using i2c_transfer for ic2 reads
PCI: brcmstb: Add DT property to control L1SS
gpiolib: Don't prevent IRQ usage of output GPIOs
snd_bcm2835: disable HDMI audio when vc4 is used (#3640)
brcmfmac: BCM43436 needs dedicated firmware
staging: vchiq_arm: Clean up 40-bit DMA support
SQUASH: pinctrl: bcm2835: Set base for bcm2711 GPIO to 0
zswap: Defer zswap initialisation
staging:vc04_services: bcm2835-camera: Request headers with I-frame
staging: vc04_services: mmal-vchiq: Update parameters list
sc16is7xx: Fix for hardware flow control
dt-bindings: media: i2c: Add IMX477 CMOS sensor binding
video: bcm2708_fb: Disable FB if no displays found
media: i2c: tc358743: Fix fallthrough warning
media: i2c: ov5647: Advertise the correct exposure range
media: i2c: ov5647: Use member names in mode tables
media: i2c: ov5647: Neither analogue gain nor exposure need EXECUTE_ON_WRITE
media: i2c: ov5647: Add support for V4L2_CID_VBLANK
media: i2c: ov5647: Set V4L2_SUBDEV_FL_HAS_EVENTS flag
media: i2c: ov5647: Support V4L2_CID_PIXEL_RATE
media: i2c: ov5467: Fixup error path to release mutex
media: i2c: ov5647: Add support for g_selection to reflect cropping/binning
media: ov5647: change defaults to better match raw camera applications.
media: ov5647: Add extra 10-bit sensor modes.
media: ov5647: Add V4L2 controls for analogue gain, exposure and AWB
media: ov5647: Add basic support for multiple sensor modes.
media: ov5647: Fix return codes from ov5647_write/ov5647_read functions.
bcm2835-dma: Add proper 40-bit DMA support
staging: vchiq: Load bcm2835_isp driver from vchiq
media: uapi: v4l-ctrls: Add CID base for the bcm2835-isp driver
media: uapi: v4l2-core: Add ISP statistics output V4L2 fourcc type
media: imx219: Advertise embedded data node on media pad 1
media: uapi: Add MEDIA_BUS_FMT_SENSOR_DATA media bus format
media: uapi: v4l2-core: Add sensor ancillary data V4L2 foucc type.
driver: char: rpivid: Don't map more than wanted
spi: Force CS_HIGH if GPIO descriptors are used
driver: char: rpivid: Remove legacy name support
drm: Checking of the pitch is only valid for linear formats
dt-bindings: display: vc4: hdmi: Add BCM2711 HDMI controllers bindings
dt-bindings: clock: Add a binding for the RPi Firmware clocks
mmc: sdhci: Silence MMC warnings
staging: media: Add Raspberry Pi V4L2 H265 decoder
media: dt-bindings: media: Add binding for the Raspberry PI HEVC decoder
media: v4l2-mem2mem: allow request job buffer processing after job finish
media: videodev2.h: Add a format for column YUV4:2:0 modes
media: uapi: Add hevc ctrls for WPP decoding
media: hevc_ctrls: Add slice param dependent slice segment
media: uapi: hevc: Add segment address field
media: uapi: hevc: Add scaling matrix control
drm/fourcc: Add packed 10bit YUV 4:2:0 format
bcmgenet: Disable skip_umac_reset by default
Kbuild: Allow .dtbo overlays to be built, adjust.
dt-bindings: pci: Add DT docs for Brcmstb PCIe device
of: overlay: Correct symbol path fixups
video: fbdev: bcm2708_fb: Use common compat header
drivers: char: vcio: Use common compat header
pinctrl: bcm2835: Accept fewer than expected IRQs
pinctrl: bcm2835: Change init order for gpio hogs
pinctrl: bcm2835: Remove gpiochip on error
staging: vchiq_arm: Give vchiq children DT nodes
Initialise rpi-firmware before clk-bcm2835
ARM: bcm: Backport BCM2711 support from upstream
staging: vchiq: Use the old dma controller for OF config on platform devices
staging: vchiq_arm: Set up dma ranges on child devices
drm/v3d: Set dma_mask as well as coherent_dma_mask
clk-bcm2835: Disable v3d clock
clk-raspberrypi: Allow cpufreq driver to also adjust gpu clocks
v3d_gem: Kick the clock so firmware knows we are using firmware clock interface
v3d_drv: Handle missing clock more gracefully
net:phy:2711 Change the default ethernet LED actions
net:phy:2711 Allow ethernet LED mode to be set via device tree
net: bcmgenet: The second IRQ is optional
staging: vchiq_arm: Register bcm2835-codec as a platform driver
staging: vchiq_arm: Register vcsm-cma as a platform driver
drm/v3d: Plug dma_fence leak
drm/v3d: Suppress all but the first MMU error
drm/v3d: Don't clear MMU control bits on exception
media: i2c: Add a driver for the Infineon IRS1125 depth sensor
dt-bindings: Add binding for the Infineon IRS1125 sensor
Rename HDMI ALSA device names, check for enable state
ARM: bcm: Switch board, clk and pinctrl to bcm2711 compatible
kbuild: Allow .dtbo overlays to be built piecemeal
drm/v3d: Delete pm_runtime support
staging: bcm2835-camera: Add greyworld AWB mode
v4l2: Add a Greyworld AWB mode.
media: dt-bindings: Add binding for the Sony IMX219 sensor
arch/arm64: Add Revision, Serial, Model to cpuinfo
arch/arm: Add model string to cpuinfo
configs: arm64/bcm2711: Enable V3D
xhci: Use more event ring segment table entries
net: bcmgenet: Workaround #2 for Pi4 Ethernet fail
Add HDMI1 facility to the driver.
hid: usb: Add device quirks for Freeway Airmouse T3 and MX3
drivers: char: add chardev for mmap'ing the RPiVid control registers
drm/v3d: Clock V3D down when not in use.
drm/v3d: HACK: gut runtime pm for now.
clk-bcm2835: Avoid null pointer exception
i2c: bcm2835: Set clock-stretch timeout to 35ms
xhci: add quirk for host controllers that don't update endpoint DCS
drm/v3d: Hook up the runtime PM ops.
drm/v3d: Skip MMU flush if the device is currently off.
drm/v3d: Add support for 2711.
arm: bcm2835: Add bcm2838 compatible string.
usbhid: call usb_fixup_endpoint after mangling intervals
xhci: implement xhci_fixup_endpoint for interval adjustments
usb: add plumbing for updating interrupt endpoint interval state
clk: bcm2835: Allow reparenting leaf clocks while they're running.
clk: bcm2835: Add support for setting leaf clock rates while running.
soc: bcm: bcm2835-pm: Add support for 2711.
clk-bcm2835: Don't wait for pllh lock
spi: bcm2835: enable shared interrupt support
usb: xhci: Disable the XHCI 5 second timeout
net: genet: enable link energy detect powerdown for external PHYs
bcmgenet: Better coalescing parameter defaults
bcmgenet: constrain max DMA burst length
bcm2835-pcm.c: Support multichannel audio
vchiq: Add 36-bit address support
mmc: sdhci-iproc: Fix vmmc regulators on iProc
hwrng: iproc-rng200: Add BCM2838 support
arm: bcm2835: DMA can only address 1GB
arm: bcm2835: Fix FIQ early ioremap
w1: w1-gpio: Make GPIO an output for strong pullup
staging: mmal-vchiq: Fix memory leak in error path
staging: mmal-vchiq: Free the event context for control ports
staging: mmal-vchiq: Update mmal_parameters.h with recently defined params
staging: mmal_vchiq: Add in the Bayer encoding formats
media: ov5647: Use gpiod_set_value_cansleep
clk: clk-bcm2835: Use %zd when printing size_t
staging: mmal-vchiq: Fix client_component for 64 bit kernel
media: videobuf2: Allow exporting of a struct dmabuf
staging: vc04_services: Support sending data to MMAL ports
staging: mmal-vchiq: Add support for event callbacks.
staging: mmal-vchiq: Avoid use of bool in structures
media: tc358743: Return an appropriate colorspace from tc358743_set_fmt
MAINTAINERS: Add entry for BCM2835 Unicam driver
dt-bindings: Document BCM283x CSI2/CCP2 receiver
media: videodev2: Add helper defines for printing FOURCCs
media: adv7180: Add YPrPb support for ADV7282M
media: adv7180: Default to the first valid input
media: tc358743: Check I2C succeeded during probe.
media: tc358743: Add support for 972Mbit/s link freq.
media: tc358743: fix connected/active CSI-2 lane reporting
media: tc358743: Increase FIFO level to 374.
media: ov5647: Add support for non-continuous clock mode
media: ov5647: Add support for PWDN GPIO.
media: ov5647: Add set_fmt and get_fmt calls.
lan78xx: use default alignment for rx buffers
rtc: rv3028: Add backup switchover mode support
bcm2835-dma: Add support for per-channel flags
lan78xx: EEE support is now a PHY property
lan78xx: Debounce link events to minimize poll storm
firmware: raspberrypi: Report the fw variant during probe
net: lan78xx: Support auto-downshift to 100Mb/s
Update issue templates (#2736)
drivers: thermal: step_wise: avoid throttling at hysteresis temperature after dropping below it
drivers: thermal: step_wise: add support for hysteresis
sc16is7xx: Don't spin if no data received
firmware: raspberrypi: Add backward compatible get_throttled
hwmon: raspberrypi: Prevent voltage low warnings from filling log
cxd2880: CXD2880_SPI_DRV should select DVB_CXD2880 with MEDIA_SUBDRV_AUTOSELECT
Add rpi-poe-fan driver
lan78xx: Move enabling of EEE into PHY init code
brcmfmac: Re-enable firmware roaming support
net: lan78xx: Disable TCP Segmentation Offload (TSO)
of: configfs: Use of_overlay_fdt_apply API call
irqchip: irq-bcm2835: Calc. FIQ_START at boot-time
firmware/raspberrypi: Notify firmware of a reboot
Add ability to export gpio used by gpio-poweroff
hid: Reduce default mouse polling interval to 60Hz
lan78xx: Read initial EEE status from DT
added capture_clear option to pps-gpio via dtoverlay (#2433)
i2c-gpio: Also set bus numbers from reg property
raspberrypi-firmware: Export the general transaction function.
ARM: Activate FIQs to avoid __irq_startup warnings
dwc-otg: FIQ: Fix "bad mode in data abort handler"
ARM: bcm2835: Set Serial number and Revision
cgroup: Disable cgroup "memory" by default
AXI performance monitor driver (#2222)
cache: export clean and invalidate
ARM64: Force hardware emulation of deprecated instructions.
ARM64: Round-Robin dispatch IRQs between CPUs.
config: Add default configs
hci_h5: Don't send conf_req when ACTIVE
brcm: adds support for BCM43341 wifi
OF: DT-Overlay configfs interface
bcm2835-virtgpio: Virtual GPIO driver
rpi_display: add backlight driver and overlay
Fixes a problem when module probes before i2c module is available
Add support for all the downstream rpi sound card drivers
mfd: Add Raspberry Pi Sense HAT core driver
gpio-poweroff: Allow it to work on Raspberry Pi
Improve __copy_to_user and __copy_from_user performance
Added Device IDs for August DVB-T 205
BCM270x_DT: Add pwr_led, and the required "input" trigger
BCM2708: Add core Device Tree support
firmware: bcm2835: Support ARCH_BCM270x
char: broadcom: Add vcio module
Add Chris Boot's i2c driver
Add SMI driver
Add /dev/gpiomem device for rootless user GPIO access
vc_mem: Add vc_mem driver for querying firmware memory addresses
Adding bcm2835-sdhost driver, and an overlay to enable it
MMC: added alternative MMC driver
dmaengine: Add support for BCM2708
Speed up console framebuffer imageblit function
fbdev: add FBIOCOPYAREA ioctl
Pulled in the multi frame buffer support from the Pi3 repo
bcm2708 framebuffer driver
Add dwc_otg driver
Main bcm2708/bcm2709 linux port
pinctrl-bcm2835: Set base to 0 give expected gpio numbering
tty: amba-pl011: Avoid rare write-when-full error
tty: amba-pl011: Add un/throttle support
tty: amba-pl011: Make TX optimisation conditional
amba_pl011: Add cts-event-workaround DT property
amba_pl011: Insert mb() for correct FIFO handling
amba_pl011: Round input clock up
amba_pl011: Don't use DT aliases for numbering
lan78xx: Enable LEDs and auto-negotiation
irqchip: irq-bcm2836: Remove regmap and syscon use
mm: Remove the PFN busy warning
i2c: bcm2835: Add debug support
Update vfpmodule.c
sound: Demote deferral errors to INFO level
clk-bcm2835: Read max core clock from firmware
clk-bcm2835: Add claim-clocks property
clk-bcm2835: Mark used PLLs and dividers CRITICAL
bcm2835-rng: Avoid initialising if already enabled
Register the clocks early during the boot process, so that special/critical clocks can get enabled early on in the boot process avoiding the risk of disabling a clock, pll_divider or pll when a claiming driver fails to install propperly - maybe it needs to defer.
bcm: Make RASPBERRYPI_POWER depend on PM
reboot: Use power off rather than busy spinning when halt is requested
watchdog: bcm2835: Support setting reboot partition
rtc: Add SPI alias for pcf2123 driver
firmware: Updated mailbox header
dmaengine: bcm2835: Load driver early and support legacy API
spi: spidev: Completely disable the spidev warning
irqchip: irq-bcm2835: Add 2836 FIQ support
irqchip: bcm2835: Add FIQ support
irq-bcm2836: Avoid "Invalid trigger warning"
Protect __release_resource against resources without parents
Allow mac address to be set in smsc95xx
smsc95xx: Experimental: Enable turbo_mode and packetsize=2560 by default
smsx95xx: fix crimes against truesize
Revert "mailbox: avoid timer start from callback"
Revert "spi: spidev: Fix CS polarity if GPIO descriptors are used"
Revert "staging: bcm2835-audio: Drop DT dependency"
Revert "rtc: pcf8523: properly handle oscillator stop bit"
arm: partially revert 702b94bff3c50542a6e4ab9a4f4cef093262fe65

[Launchpad Janitor (janitor)]

This bug was fixed in the package linux-raspi - 5.11.0-1003.3

---------------
linux-raspi (5.11.0-1003.3) hirsute; urgency=medium

  * hirsute/linux-raspi: 5.11.0-1003.3 -proposed tracker (LP: #1917734)

  * Packaging resync (LP: #1786013)
    - [Packaging] update variants
    - [Packaging] update update.conf

  * Miscellaneous Ubuntu changes
    - [Packaging] raspi: Initial version of linux-raspi for Hirsute
    - [Config] raspi: updateconfigs after rebase to Ubuntu-5.11.0-11.12
    - [Packaging] raspi: Set disable_d_i=true in hooks.mk
    - [Packaging] raspi: Add dctrl-tools to Build-Depends
    - [Packaging] raspi: Correctly implement noudeb build profiles
    - [Packaging] raspi: remove Provides: aufs-dkms

  [ Ubuntu: 5.11.0-11.12 ]

  * hirsute/linux: 5.11.0-11.12 -proposed tracker (LP: #1917335)
  * Packaging resync (LP: #1786013)
    - update dkms package versions
    - [Packaging] update variants
  * Support no udeb profile (LP: #1916095)
    - [Packaging] replace custom filter script with dctrl-tools
    - [Packaging] correctly implement noudeb build profiles.
  * Miscellaneous Ubuntu changes
    - [Packaging] dkms-versions -- remove nvidia-graphics-drivers-440-server
    - [Debian] run ubuntu-regression-suite for linux-unstable
    - [Packaging] remove Provides: aufs-dkms
    - [Packaging] Change source package name to linux
    - [Config] update gcc version in config due to toolchain update
  * Miscellaneous upstream changes
    - Revert "UBUNTU: [Config] disable nvidia and nvidia_server builds"
    - Xen/x86: don't bail early from clear_foreign_p2m_mapping()
    - Xen/x86: also check kernel mapping in set_foreign_p2m_mapping()
    - Xen/gntdev: correct dev_bus_addr handling in gntdev_map_grant_pages()
    - Xen/gntdev: correct error checking in gntdev_map_grant_pages()
    - xen/arm: don't ignore return errors from set_phys_to_machine
    - xen-blkback: don't "handle" error by BUG()
    - xen-netback: don't "handle" error by BUG()
    - xen-scsiback: don't "handle" error by BUG()
    - xen-blkback: fix error handling in xen_blkbk_map()
    - tty: protect tty_write from odd low-level tty disciplines
    - Bluetooth: btusb: Always fallback to alt 1 for WBS
    - media: pwc: Use correct device for DMA
    - bpf: Fix truncation handling for mod32 dst reg wrt zero
    - HID: make arrays usage and value to be the same
    - USB: quirks: sort quirk entries
    - usb: quirks: add quirk to start video capture on ELMO L-12F document camera
      reliable
    - ntfs: check for valid standard information attribute
    - Bluetooth: btusb: Some Qualcomm Bluetooth adapters stop working
    - arm64: tegra: Add power-domain for Tegra210 HDA
    - hwmon: (dell-smm) Add XPS 15 L502X to fan control blacklist
    - KVM: x86: Zap the oldest MMU pages, not the newest
    - KVM: do not assume PTE is writable after follow_pfn
    - mm: provide a saner PTE walking API for modules
    - KVM: Use kvm_pfn_t for local PFN variable in hva_to_pfn_remapped()

 -- Juerg Haefliger <email address hidden> Thu, 04 Mar 2021 14:42:19 +0100