Periodic system freeze

[Jean-Paul Calderone]

About once a week (but as frequently twice a day and as infrequently as once a
month), my system freezes up completely. After power cycling the system is fine
again until the next time. Often this will happen overnight when the system is
not responding to user input. The system has been stable with previous linux
installs. I am currently using Hoary Hedgehog. I'm uncertain as to the exact
version, however these two lines appear in my /etc/apt/sources.list file:

deb cdrom:[Ubuntu 5.04 _Hoary Hedgehog_ - Preview i386 Binary-1 (20050310)]/
hoary main restricted
deb cdrom:[Ubuntu 5.04 _Hoary Hedgehog_ - Alpha i386 Binary-1 (20050206)]/
unstable main restricted

Below is the output of various commands which may be helpful. If there is more
information I should provide, let me know.

================================
Output of lspci -vvv:

0000:00:00.0 Host bridge: Intel Corp. 82875P Memory Controller Hub (rev 02)
        Subsystem: Asustek Computer, Inc.: Unknown device 80f6
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
        Latency: 0
        Region 0: Memory at f4000000 (32-bit, prefetchable) [size=64M]
        Capabilities: [e4] #09 [2106]
        Capabilities: [a0] AGP version 3.0
                Status: RQ=32 Iso- ArqSz=2 Cal=2 SBA+ ITACoh- GART64- HTrans-
64bit- FW+ AGP3+ Rate=x4,x8
                Command: RQ=1 ArqSz=0 Cal=2 SBA+ AGP+ GART64- 64bit- FW- Rate=x8

0000:00:01.0 PCI bridge: Intel Corp. 82875P Processor to AGP Controller (rev 02)
(prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
        Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
        Latency: 64
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
        I/O behind bridge: 0000f000-00000fff
        Memory behind bridge: fc900000-fe9fffff
        Prefetchable memory behind bridge: dff00000-efefffff
        BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-

0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev c2) (prog-if 00
[Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
        Latency: 0
        Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
        I/O behind bridge: 0000d000-0000dfff
        Memory behind bridge: fea00000-feafffff
        Prefetchable memory behind bridge: fff00000-000fffff
        BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-

0000:00:1f.0 ISA bridge: Intel Corp. 82801EB/ER (ICH5/ICH5R) LPC Bridge (rev 02)
        Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0

0000:00:1f.1 IDE interface: Intel Corp. 82801EB/ER (ICH5/ICH5R) Ultra ATA 100
Storage Controller (rev 02) (prog-if 8a [Master SecP PriP])
        Subsystem: Asustek Computer, Inc. P4P800 Mainboard
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin A routed to IRQ 18
        Region 0: I/O ports at <unassigned>
        Region 1: I/O ports at <unassigned>
        Region 2: I/O ports at <unassigned>
        Region 3: I/O ports at <unassigned>
        Region 4: I/O ports at fc00 [size=16]
        Region 5: Memory at 40000000 (32-bit, non-prefetchable) [size=1K]
0000:00:1f.2 IDE interface: Intel Corp. 82801EB (ICH5) Serial ATA 150 Storage
Controller (rev 02) (prog-if 8f [Master SecP SecO PriP PriO])
        Subsystem: Asustek Computer, Inc.: Unknown device 80a6
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin A routed to IRQ 18
        Region 0: I/O ports at efe0 [size=8]
        Region 1: I/O ports at efac [size=4]
        Region 2: I/O ports at efa0 [size=8]
        Region 3: I/O ports at efa8 [size=4]
        Region 4: I/O ports at ef90 [size=16]

0000:00:1f.3 SMBus: Intel Corp. 82801EB/ER (ICH5/ICH5R) SMBus Controller (rev 02)
        Subsystem: Asustek Computer, Inc. P4P800 Mainboard
        Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin B routed to IRQ 11
        Region 4: I/O ports at 0400 [size=32]

0000:00:1f.5 Multimedia audio controller: Intel Corp. 82801EB/ER (ICH5/ICH5R)
AC'97 Audio Controller (rev 02)
        Subsystem: Asustek Computer, Inc. P4P800 Mainboard
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin B routed to IRQ 17
        Region 0: I/O ports at e800 [size=256]
        Region 1: I/O ports at ef00 [size=64]
        Region 2: Memory at febffc00 (32-bit, non-prefetchable) [size=512]
        Region 3: Memory at febff800 (32-bit, non-prefetchable) [size=256]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:01:00.0 VGA compatible controller: nVidia Corporation NV28 [GeForce4 Ti
4200 AGP 8x] (rev a1) (prog-if 00 [VGA])
        Subsystem: Asustek Computer, Inc.: Unknown device 807b
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 248 (1250ns min, 250ns max)
        Interrupt: pin A routed to IRQ 16
        Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
        Region 1: Memory at e0000000 (32-bit, prefetchable) [size=128M]
        Expansion ROM at fe9e0000 [disabled] [size=128K]
        Capabilities: [60] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [44] AGP version 3.0
                Status: RQ=32 Iso- ArqSz=0 Cal=3 SBA+ ITACoh- GART64- HTrans-
64bit- FW+ AGP3+ Rate=x4,x8
                Command: RQ=32 ArqSz=2 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x8

0000:02:03.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host
Controller (rev 80) (prog-if 10 [OHCI])
        Subsystem: Asustek Computer, Inc.: Unknown device 808a
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (8000ns max), Cache Line Size: 0x04 (16 bytes)
        Interrupt: pin A routed to IRQ 20
        Region 0: Memory at feaff800 (32-bit, non-prefetchable) [size=2K]
        Region 1: I/O ports at dc00 [size=128]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA
PME(D0-,D1-,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:02:05.0 Ethernet controller: 3Com Corporation 3c940 10/100/1000Base-T
[Marvell] (rev 12)
        Subsystem: Asustek Computer, Inc. P4P800 Mainboard
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (5750ns min, 7750ns max), Cache Line Size: 0x04 (16 bytes)
        Interrupt: pin A routed to IRQ 22
        Region 0: Memory at feaf8000 (32-bit, non-prefetchable) [size=16K]
        Region 1: I/O ports at d800 [size=256]
        Capabilities: [48] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=1 PME-
        Capabilities: [50] Vital Product Data

0000:02:0a.0 Multimedia audio controller: Yamaha Corporation YMF-724 (rev 03)
        Subsystem: Yamaha Corporation YMF724-Based PCI Audio Adapter
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR+
        Latency: 64 (1250ns min, 6250ns max)
        Interrupt: pin A routed to IRQ 22
        Region 0: Memory at feaf0000 (32-bit, non-prefetchable) [size=32K]
        Capabilities: [50] Power Management version 1
                Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:02:0c.0 Network controller: Broadcom Corporation BCM4301 802.11b (rev 02)
        Subsystem: Linksys: Unknown device 4301
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
        Latency: 64
        Interrupt: pin A routed to IRQ 5
        Region 0: Memory at feafc000 (32-bit, non-prefetchable) [size=8K]
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=2 PME+

===============================
Output of lsmod:

Module Size Used by
proc_intf 4260 0
freq_table 4320 0
cpufreq_userspace 6240 0
cpufreq_ondemand 6728 0
cpufreq_powersave 1856 0
video 16196 0
sony_acpi 6152 0
pcc_acpi 11232 0
button 6704 0
battery 10212 0
container 4544 0
ac 4900 0
ipv6 257760 13
af_packet 22504 2
uhci_hcd 33488 0
ohci_hcd 21992 0
ehci_hcd 33252 0
usbcore 119480 3 uhci_hcd,ohci_hcd,ehci_hcd
snd_ymfpci 59712 0
snd_opl3_lib 11072 1 snd_ymfpci
snd_hwdep 9700 1 snd_opl3_lib
gameport 4864 1 snd_ymfpci
snd_mpu401_uart 8224 1 snd_ymfpci
snd_rawmidi 25024 1 snd_mpu401_uart
snd_seq_device 8716 2 snd_opl3_lib,snd_rawmidi
sk98lin 171968 0
ohci1394 34916 0
snd_intel8x0 32928 1
snd_ac97_codec 74336 2 snd_ymfpci,snd_intel8x0
snd_pcm_oss 52836 0
snd_mixer_oss 19968 2 snd_pcm_oss
snd_pcm 95780 4 snd_ymfpci,snd_intel8x0,snd_ac97_codec,snd_pcm_oss
snd_timer 25572 3 snd_ymfpci,snd_opl3_lib,snd_pcm
snd 56580 12
snd_ymfpci,snd_opl3_lib,snd_hwdep,snd_mpu401_uart,snd_rawmidi,snd_seq_device,snd_intel8x0,snd_ac97_codec,snd_
pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
soundcore 10400 2 snd
snd_page_alloc 9988 3 snd_ymfpci,snd_intel8x0,snd_pcm
i2c_i801 8652 0
i2c_core 22720 1 i2c_i801
piix 10884 1
hw_random 5620 0
shpchp 99620 0
pci_hotplug 33980 1 shpchp
intel_mch_agp 10512 0
intel_agp 22396 1
floppy 59472 0
pcspkr 3788 0
rtc 12776 0
md 48112 0
dm_mod 60480 1
capability 4872 0
commoncap 8032 1 capability
nvidia 3923420 20
agpgart 34284 3 intel_mch_agp,intel_agp,nvidia
sbp2 24008 0
ieee1394 108856 2 ohci1394,sbp2
evdev 9600 0
psmouse 21736 0
mousedev 11612 0
parport_pc 37924 1
lp 11464 0
parport 37352 2 parport_pc,lp
ide_generic 1536 0
ide_disk 20896 1
ide_cd 42052 0
ide_core 129656 4 piix,ide_generic,ide_disk,ide_cd
ext3 138664 6
jbd 63544 1 ext3
mbcache 8452 1 ext3
sr_mod 17444 0
cdrom 40476 2 ide_cd,sr_mod
sd_mod 18080 7
sg 38656 0
ata_piix 9412 12
libata 49508 1 ata_piix
scsi_mod 128224 5 sbp2,sr_mod,sd_mod,sg,libata
unix 28692 840
thermal 13672 0
processor 23400 1 thermal
fan 4612 0
fbcon 37856 0
font 8416 1 fbcon
bitblit 5696 1 fbcon
vesafb 6948 0
cfbcopyarea 4032 1 vesafb
cfbimgblt 3136 1 vesafb
cfbfillrect 3712 1 vesafb

============================================
Output of cat /proc/cpuinfo

processor : 0
vendor_id : GenuineIntel
cpu family : 15
model : 2
model name : Intel(R) Pentium(R) 4 CPU 3.00GHz
stepping : 9
cpu MHz : 2998.860
cache size : 512 KB
physical id : 0
siblings : 2
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov
pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe cid xtpr
bogomips : 5947.39

processor : 1
vendor_id : GenuineIntel
cpu family : 15
model : 2
model name : Intel(R) Pentium(R) 4 CPU 3.00GHz
stepping : 9
cpu MHz : 2998.860
cache size : 512 KB
physical id : 0
siblings : 2
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov
pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe cid xtpr
bogomips : 5980.16

========================================
Output of dmesg

Linux version 2.6.10-5-686-smp (buildd@rothera) (gcc version 3.3.5 (Debian
1:3.3.5-8ubuntu2)) #1 SMP Fri Apr 1 16:56:25 UTC 2005
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003ff30000 (usable)
 BIOS-e820: 000000003ff30000 - 000000003ff40000 (ACPI data)
 BIOS-e820: 000000003ff40000 - 000000003fff0000 (ACPI NVS)
 BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved)
 BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000ff780
On node 0 totalpages: 261936
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 225280 pages, LIFO batch:16
  HighMem zone: 32560 pages, LIFO batch:7
DMI 2.3 present.
ACPI: RSDP (v000 ACPIAM ) @ 0x000f9fb0
ACPI: RSDT (v001 A M I OEMRSDT 0x06000323 MSFT 0x00000097) @ 0x3ff30000
ACPI: FADT (v002 A M I OEMFACP 0x06000323 MSFT 0x00000097) @ 0x3ff30200
ACPI: MADT (v001 A M I OEMAPIC 0x06000323 MSFT 0x00000097) @ 0x3ff30390
ACPI: OEMB (v001 A M I OEMBIOS 0x06000323 MSFT 0x00000097) @ 0x3ff40040
ACPI: DSDT (v001 P4C81 P4C81078 0x00000078 INTL 0x02002026) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:2 APIC version 20
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Kernel command line: root=/dev/sda1 ro quiet splash
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 2998.860 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1030320k/1047744k available (1604k kernel code, 16664k reserved, 719k
data, 192k init, 130240k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 5947.39 BogoMIPS (lpj=2973696)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400
00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400
00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: Looking for DSDT in initrd... not found!
CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09
per-CPU timeslice cutoff: 1462.98 usecs.
task migration cache decay timeout: 2 msecs.
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay loop... 5980.16 BogoMIPS (lpj=2990080)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400
00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400
00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09
Total of 2 processors activated (11927.55 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
CPU0:
 domain 0: span 03
  groups: 01 02
  domain 1: span 03
   groups: 03
CPU1:
 domain 0: span 03
  groups: 02 01
  domain 1: span 03
   groups: 03
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like
an initrd
Freeing initrd memory: 4556k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to <email address hidden>
** so I can fix the driver.
pnp: 00:09: ioport range 0x680-0x6ff has been reserved
pnp: 00:09: ioport range 0x290-0x297 has been reserved
audit: initializing netlink socket (disabled)
audit(1112603496.896:0): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (<email address hidden>)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
Restarting tasks...<6> Strange, kswapd0 not stopped
 Strange, kseriod not stopped
 done
ACPI wakeup devices:
P0P4 MC97 USB1 USB2 USB3 USB4 EUSB PS2K ILAN PWRB
ACPI: (supports S0 S1 S3 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4556KiB [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 192k freed
NET: Registered protocol family 1
SCSI subsystem initialized
libata version 1.10 loaded.
ata_piix version 1.03
ACPI: PCI interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0xEFE0 ctl 0xEFAE bmdma 0xEF90 irq 18
ata2: SATA max UDMA/133 cmd 0xEFA0 ctl 0xEFAA bmdma 0xEF98 irq 18
ata1: dev 0 cfg 49:0f00 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000 88:0407
ata1: dev 0 ATAPI, max UDMA/33
ata1(0): applying bridge limits
ata1: dev 0 configured for UDMA/33
scsi0 : ata_piix
ata2: dev 0 cfg 49:2f00 82:346b 83:7f21 84:4003 85:3469 86:3c01 87:4003 88:203f
ata2: dev 0 ATA, max UDMA/100, 234441648 sectors: lba48
ata2(0): applying bridge limits
ata2: dev 0 configured for UDMA/100
scsi1 : ata_piix
elevator: using anticipatory as default io scheduler
  Vendor: PLEXTOR Model: DVDR PX-712A Rev: 1.05
  Type: CD-ROM ANSI SCSI revision: 05
  Vendor: ATA Model: WDC WD1200JD-00F Rev: 02.0
  Type: Direct-Access ANSI SCSI revision: 05
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 5
Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 0
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
SCSI device sda: drive cache: write back
 /dev/scsi/host1/bus0/target0/lun0: p1 p2 p3 p4 < p5 p6 p7 >
Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 125x/94x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0EXT3-fs: INFO: recovery
required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
EXT3 FS on sda1, internal journal
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
hdb: PLEXTOR CD-R PX-W1210A, ATAPI CD/DVD-ROM drive
Probing IDE interface ide1...
hdd: Maxtor 94098U8, ATA DISK drive
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hdb: ATAPI 32X CD-ROM CD-R/RW drive, 2048kB Cache
hdd: max request size: 128KiB
hdd: 80041248 sectors (40981 MB) w/2048KiB Cache, CHS=65535/16/63
hdd: cache flushes not supported
 /dev/ide/host1/bus0/target1/lun0: p1 p2
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3
[PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
lp0: using parport0 (interrupt-driven).
mice: PS/2 mouse device common for all mice
ieee1394: Initialized config rom entry `ip1394'
sbp2: $Rev: 1219 $ Ben Collins <email address hidden>
Linux agpgart interface v0.100 (c) Dave Jones
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-7167 Fri Feb 25
09:08:22 PST 2005
Capability LSM initialized
device-mapper: 4.3.0-ioctl (2004-09-30) initialised: <email address hidden>
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
cdrom: open failed.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: mounting unchecked fs, running e2fsck is recommended
EXT3 FS on sda2, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: mounting unchecked fs, running e2fsck is recommended
EXT3 FS on sda7, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Real Time Clock Driver v1.12
input: PC Speaker
inserting floppy driver for 2.6.10-5-686-smp
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
agpgart: Detected an Intel i875 Chipset.
agpgart: Maximum main memory to use for agp memory: 941M
agpgart: AGP aperture is 64M @ 0xf4000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Evaluate _OSC Set fails. Status = 0x0005
pciehp: add_host_bridge: status 5
pciehp: Fails to gain control of native hot-plug
Evaluate _OSC Set fails. Status = 0x0005
pciehp: add_host_bridge: status 5
pciehp: Fails to gain control of native hot-plug
hw_random hardware driver 1.0.0 loaded
ICH5: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
ICH5: port 0x01f0 already claimed by ide0
ICH5: port 0x0170 already claimed by ide1
ICH5: neither IDE port enabled (BIOS)
ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1f.5 to 64
AC'97 0 analog subsections not ready
intel8x0_measure_ac97_clock: measured 49578 usecs
intel8x0: clocking to 48000
ohci1394: $Rev: 1223 $ Ben Collins <email address hidden>
ACPI: PCI interrupt 0000:02:03.0[A] -> GSI 20 (level, low) -> IRQ 20
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[20] MMIO=[feaff800-feafffff] Max
Packet=[2048]
ACPI: PCI interrupt 0000:02:05.0[A] -> GSI 22 (level, low) -> IRQ 22
ACPI: PCI interrupt 0000:02:05.0[A] -> GSI 22 (level, low) -> IRQ 22
eth0: 3Com Gigabit LOM (3C940)
      PrefPort:A RlmtMode:Check Link State
ACPI: PCI interrupt 0000:02:0a.0[A] -> GSI 22 (level, low) -> IRQ 22
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
USB Universal Host Controller Interface driver v2.2
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e0180000283774]
NET: Registered protocol family 17
eth0: network connection up using port A
    speed: 100
    autonegotiation: yes
    duplex mode: full
    flowctrl: symmetric
    irq moderation: disabled
    scatter-gather: enabled
eth0: network connection down
eth0: network connection up using port A
    speed: 100
    autonegotiation: yes
    duplex mode: full
    flowctrl: symmetric
    irq moderation: disabled
    scatter-gather: enabled
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0317e40(lo)
IPv6 over IPv4 tunneling driver
ACPI: Power Button (FF) [PWRF]
ibm_acpi: ec object not found
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
cdrom: This disc doesn't have any tracks I recognize!
eth0: no IPv6 routers present
ATA: abnormal status 0x58 on port 0xEFE7
ATA: abnormal status 0x58 on port 0xEFE7
ATA: abnormal status 0x58 on port 0xEFE7
ATA: abnormal status 0x58 on port 0xEFE7
ATA: abnormal status 0x58 on port 0xEFE7
ATA: abnormal status 0x58 on port 0xEFE7
ATA: abnormal status 0x58 on port 0xEFE7
ATA: abnormal status 0x58 on port 0xEFE7
ata1: dev 0: ATAPI check failed
cdrom: This disc doesn't have any tracks I recognize!
root@boson:~# dmesg
Linux version 2.6.10-5-686-smp (buildd@rothera) (gcc version 3.3.5 (Debian
1:3.3.5-8ubuntu2)) #1 SMP Fri Apr 1 16:56:25 UTC 2005
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003ff30000 (usable)
 BIOS-e820: 000000003ff30000 - 000000003ff40000 (ACPI data)
 BIOS-e820: 000000003ff40000 - 000000003fff0000 (ACPI NVS)
 BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved)
 BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000ff780
On node 0 totalpages: 261936
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 225280 pages, LIFO batch:16
  HighMem zone: 32560 pages, LIFO batch:7
DMI 2.3 present.
ACPI: RSDP (v000 ACPIAM ) @ 0x000f9fb0
ACPI: RSDT (v001 A M I OEMRSDT 0x06000323 MSFT 0x00000097) @ 0x3ff30000
ACPI: FADT (v002 A M I OEMFACP 0x06000323 MSFT 0x00000097) @ 0x3ff30200
ACPI: MADT (v001 A M I OEMAPIC 0x06000323 MSFT 0x00000097) @ 0x3ff30390
ACPI: OEMB (v001 A M I OEMBIOS 0x06000323 MSFT 0x00000097) @ 0x3ff40040
ACPI: DSDT (v001 P4C81 P4C81078 0x00000078 INTL 0x02002026) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:2 APIC version 20
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Kernel command line: root=/dev/sda1 ro quiet splash
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 2998.860 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1030320k/1047744k available (1604k kernel code, 16664k reserved, 719k
data, 192k init, 130240k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 5947.39 BogoMIPS (lpj=2973696)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400
00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400
00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: Looking for DSDT in initrd... not found!
CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09
per-CPU timeslice cutoff: 1462.98 usecs.
task migration cache decay timeout: 2 msecs.
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay loop... 5980.16 BogoMIPS (lpj=2990080)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400
00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400
00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09
Total of 2 processors activated (11927.55 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
CPU0:
 domain 0: span 03
  groups: 01 02
  domain 1: span 03
   groups: 03
CPU1:
 domain 0: span 03
  groups: 02 01
  domain 1: span 03
   groups: 03
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like
an initrd
Freeing initrd memory: 4556k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to <email address hidden>
** so I can fix the driver.
pnp: 00:09: ioport range 0x680-0x6ff has been reserved
pnp: 00:09: ioport range 0x290-0x297 has been reserved
audit: initializing netlink socket (disabled)
audit(1112603496.896:0): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (<email address hidden>)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
Restarting tasks...<6> Strange, kswapd0 not stopped
 Strange, kseriod not stopped
 done
ACPI wakeup devices:
P0P4 MC97 USB1 USB2 USB3 USB4 EUSB PS2K ILAN PWRB
ACPI: (supports S0 S1 S3 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4556KiB [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 192k freed
NET: Registered protocol family 1
SCSI subsystem initialized
libata version 1.10 loaded.
ata_piix version 1.03
ACPI: PCI interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0xEFE0 ctl 0xEFAE bmdma 0xEF90 irq 18
ata2: SATA max UDMA/133 cmd 0xEFA0 ctl 0xEFAA bmdma 0xEF98 irq 18
ata1: dev 0 cfg 49:0f00 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000 88:0407
ata1: dev 0 ATAPI, max UDMA/33
ata1(0): applying bridge limits
ata1: dev 0 configured for UDMA/33
scsi0 : ata_piix
ata2: dev 0 cfg 49:2f00 82:346b 83:7f21 84:4003 85:3469 86:3c01 87:4003 88:203f
ata2: dev 0 ATA, max UDMA/100, 234441648 sectors: lba48
ata2(0): applying bridge limits
ata2: dev 0 configured for UDMA/100
scsi1 : ata_piix
elevator: using anticipatory as default io scheduler
  Vendor: PLEXTOR Model: DVDR PX-712A Rev: 1.05
  Type: CD-ROM ANSI SCSI revision: 05
  Vendor: ATA Model: WDC WD1200JD-00F Rev: 02.0
  Type: Direct-Access ANSI SCSI revision: 05
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 5
Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 0
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
SCSI device sda: drive cache: write back
 /dev/scsi/host1/bus0/target0/lun0: p1 p2 p3 p4 < p5 p6 p7 >
Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 125x/94x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
EXT3 FS on sda1, internal journal
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
hdb: PLEXTOR CD-R PX-W1210A, ATAPI CD/DVD-ROM drive
Probing IDE interface ide1...
hdd: Maxtor 94098U8, ATA DISK drive
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hdb: ATAPI 32X CD-ROM CD-R/RW drive, 2048kB Cache
hdd: max request size: 128KiB
hdd: 80041248 sectors (40981 MB) w/2048KiB Cache, CHS=65535/16/63
hdd: cache flushes not supported
 /dev/ide/host1/bus0/target1/lun0: p1 p2
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3
[PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
lp0: using parport0 (interrupt-driven).
mice: PS/2 mouse device common for all mice
ieee1394: Initialized config rom entry `ip1394'
sbp2: $Rev: 1219 $ Ben Collins <email address hidden>
Linux agpgart interface v0.100 (c) Dave Jones
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-7167 Fri Feb 25
09:08:22 PST 2005
Capability LSM initialized
device-mapper: 4.3.0-ioctl (2004-09-30) initialised: <email address hidden>
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
cdrom: open failed.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: mounting unchecked fs, running e2fsck is recommended
EXT3 FS on sda2, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: mounting unchecked fs, running e2fsck is recommended
EXT3 FS on sda7, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Real Time Clock Driver v1.12
input: PC Speaker
inserting floppy driver for 2.6.10-5-686-smp
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
agpgart: Detected an Intel i875 Chipset.
agpgart: Maximum main memory to use for agp memory: 941M
agpgart: AGP aperture is 64M @ 0xf4000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Evaluate _OSC Set fails. Status = 0x0005
pciehp: add_host_bridge: status 5
pciehp: Fails to gain control of native hot-plug
Evaluate _OSC Set fails. Status = 0x0005
pciehp: add_host_bridge: status 5
pciehp: Fails to gain control of native hot-plug
hw_random hardware driver 1.0.0 loaded
ICH5: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
ICH5: port 0x01f0 already claimed by ide0
ICH5: port 0x0170 already claimed by ide1
ICH5: neither IDE port enabled (BIOS)
ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1f.5 to 64
AC'97 0 analog subsections not ready
intel8x0_measure_ac97_clock: measured 49578 usecs
intel8x0: clocking to 48000
ohci1394: $Rev: 1223 $ Ben Collins <email address hidden>
ACPI: PCI interrupt 0000:02:03.0[A] -> GSI 20 (level, low) -> IRQ 20
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[20] MMIO=[feaff800-feafffff] Max
Packet=[2048]
ACPI: PCI interrupt 0000:02:05.0[A] -> GSI 22 (level, low) -> IRQ 22
ACPI: PCI interrupt 0000:02:05.0[A] -> GSI 22 (level, low) -> IRQ 22
eth0: 3Com Gigabit LOM (3C940)
      PrefPort:A RlmtMode:Check Link State
ACPI: PCI interrupt 0000:02:0a.0[A] -> GSI 22 (level, low) -> IRQ 22
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
USB Universal Host Controller Interface driver v2.2
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e0180000283774]
NET: Registered protocol family 17
eth0: network connection up using port A
    speed: 100
    autonegotiation: yes
    duplex mode: full
    flowctrl: symmetric
    irq moderation: disabled
    scatter-gather: enabled
eth0: network connection down
eth0: network connection up using port A
    speed: 100
    autonegotiation: yes
    duplex mode: full
    flowctrl: symmetric
    irq moderation: disabled
    scatter-gather: enabled
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0317e40(lo)
IPv6 over IPv4 tunneling driver
ACPI: Power Button (FF) [PWRF]
ibm_acpi: ec object not found
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
cdrom: This disc doesn't have any tracks I recognize!
eth0: no IPv6 routers present
ATA: abnormal status 0x58 on port 0xEFE7
ATA: abnormal status 0x58 on port 0xEFE7
ATA: abnormal status 0x58 on port 0xEFE7
ATA: abnormal status 0x58 on port 0xEFE7
ATA: abnormal status 0x58 on port 0xEFE7
ATA: abnormal status 0x58 on port 0xEFE7
ATA: abnormal status 0x58 on port 0xEFE7
ATA: abnormal status 0x58 on port 0xEFE7
ata1: dev 0: ATAPI check failed
cdrom: This disc doesn't have any tracks I recognize!

[Matt Zimmerman (mdz)]

Please:

- Run a memory test (a thorough test is available from the GRUB menu)
- Follow http://www.ubuntu.com/wiki/DebuggingSystemCrash

[Ben Collins (ben-collins)]

No response from submitter.