[   18.381835] init: gdm main process (1309) killed by TERM signal
[   18.440046] psmouse serio4: elantech: assuming hardware version 4 (with firmware version 0x361f02)
[   18.452401] psmouse serio4: elantech: Synaptics capabilities query result 0x00, 0x15, 0x0e.
[   18.510503] iwlwifi 0000:02:00.0: L1 Disabled; Enabling L0S
[   18.517090] iwlwifi 0000:02:00.0: Radio type=0x2-0x1-0x0
[   18.518528] input: ETPS/2 Elantech Touchpad as /devices/platform/i8042/serio4/input/input11
[   18.912319] iwlwifi 0000:02:00.0: L1 Disabled; Enabling L0S
[   18.918895] iwlwifi 0000:02:00.0: Radio type=0x2-0x1-0x0
[   19.148342] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   19.148627] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   19.401649] Adding 4075516k swap on /dev/mapper/cryptswap1.  Priority:-1 extents:1 across:4075516k SS
[   25.398132] wlan0: authenticate with 84:9c:a6:e5:ff:ca
[   25.406136] wlan0: send auth to 84:9c:a6:e5:ff:ca (try 1/3)
[   25.408579] wlan0: authenticated
[   25.411479] wlan0: associate with 84:9c:a6:e5:ff:ca (try 1/3)
[   25.416103] wlan0: RX AssocResp from 84:9c:a6:e5:ff:ca (capab=0x411 status=0 aid=2)
[   25.445799] wlan0: associated
[   25.445867] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   25.445984] cfg80211: Calling CRDA for country: NL
[   25.448996] cfg80211: Regulatory domain changed to country: NL
[   25.448999] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   25.449000] cfg80211:   (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   25.449002] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   25.449003] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   25.449004] cfg80211:   (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
[   25.531780] CPU3: Package power limit notification (total events = 1)
[   25.531782] CPU0: Package power limit notification (total events = 1)
[   25.531784] CPU2: Package power limit notification (total events = 1)
[   25.531785] CPU1: Package power limit notification (total events = 1)
[   25.542785] CPU0: Package power limit normal
[   25.542786] CPU2: Package power limit normal
[   25.542788] CPU1: Package power limit normal
[   25.542789] CPU3: Package power limit normal
[   26.724700] IPv6: wlan0: IPv6 duplicate address fe80::c685:8ff:fe4c:a7b6 detected!
[   27.987368] audit_printk_skb: 57 callbacks suppressed
[   27.987371] type=1400 audit(1378392204.467:31): apparmor="DENIED" operation="open" parent=1 profile="/usr/lib/telepathy/telepathy-*" name="/usr/share/p11-kit/modules/" pid=2579 comm="telepathy-gabbl" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[  377.304317] usb 3-2: USB disconnect, device number 2
[  492.102735] wlan0: deauthenticating from 84:9c:a6:e5:ff:ca by local choice (reason=3)
[  492.139887] cfg80211: Calling CRDA to update world regulatory domain
[  492.148318] cfg80211: World regulatory domain updated:
[  492.148326] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[  492.148331] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[  492.148336] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[  492.148339] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[  492.148343] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[  492.148347] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[  493.287448] PM: Syncing filesystems ... done.
[  495.070753] Freezing user space processes ... (elapsed 0.01 seconds) done.
[  495.086107] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
[  495.102382] Suspending console(s) (use no_console_suspend to debug)
[  495.102599] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[  495.104161] sd 0:0:0:0: [sda] Stopping disk
[  496.296231] PM: suspend of devices complete after 1195.520 msecs
[  496.296362] PM: late suspend of devices complete after 0.130 msecs
[  496.312265] ehci-pci 0000:00:1d.0: System wakeup enabled by ACPI
[  496.328251] ehci-pci 0000:00:1a.0: System wakeup enabled by ACPI
[  496.360098] xhci_hcd 0000:00:14.0: System wakeup enabled by ACPI
[  496.376081] PM: noirq suspend of devices complete after 79.835 msecs
[  496.376333] ACPI: Preparing to enter system sleep state S3
[  496.536027] PM: Saving platform NVS memory
[  496.589946] Disabling non-boot CPUs ...
[  496.691553] smpboot: CPU 1 is now offline
[  496.691963] Broke affinity for irq 46
[  496.692973] smpboot: CPU 2 is now offline
[  496.694499] smpboot: CPU 3 is now offline
[  496.694708] Extended CMOS year: 2000
[  496.696313] ACPI: Low-level resume complete
[  496.696369] PM: Restoring platform NVS memory
[  496.698301] Extended CMOS year: 2000
[  496.698378] Enabling non-boot CPUs ...
[  496.698467] smpboot: Booting Node 0 Processor 1 APIC 0x2
[  496.712443] CPU1 is up
[  496.712506] smpboot: Booting Node 0 Processor 2 APIC 0x1
[  496.726489] CPU2 is up
[  496.726548] smpboot: Booting Node 0 Processor 3 APIC 0x3
[  496.740480] CPU3 is up
[  496.748155] ACPI: Waking up from system sleep state S3
[  496.850969] xhci_hcd 0000:00:14.0: System wakeup disabled by ACPI
[  496.882911] ehci-pci 0000:00:1a.0: System wakeup disabled by ACPI
[  496.914860] ehci-pci 0000:00:1d.0: System wakeup disabled by ACPI
[  496.946966] PM: noirq resume of devices complete after 127.990 msecs
[  496.947087] PM: early resume of devices complete after 0.093 msecs
[  496.947119] i915 0000:00:02.0: setting latency timer to 64
[  496.947136] xhci_hcd 0000:00:14.0: setting latency timer to 64
[  496.947202] ehci-pci 0000:00:1a.0: setting latency timer to 64
[  496.947216] mei 0000:00:16.0: irq 45 for MSI/MSI-X
[  496.947285] snd_hda_intel 0000:00:1b.0: irq 47 for MSI/MSI-X
[  496.947303] ehci-pci 0000:00:1d.0: setting latency timer to 64
[  496.947339] ahci 0000:00:1f.2: setting latency timer to 64
[  497.182243] usb 2-1.5: reset high-speed USB device number 3 using ehci-pci
[  497.398310] usb 1-1.2: reset high-speed USB device number 3 using ehci-pci
[  497.489993] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[  497.492743] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[  497.492906] ata1.00: ACPI cmd ef/10:06:00:00:00:a0 (SET FEATURES) succeeded
[  497.492907] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[  497.512735] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[  497.512934] ata1.00: ACPI cmd ef/10:06:00:00:00:a0 (SET FEATURES) succeeded
[  497.512936] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[  497.523354] ata1.00: configured for UDMA/133
[  497.537980] sd 0:0:0:0: [sda] Starting disk
[  497.538088] PM: resume of devices complete after 591.879 msecs
[  497.852591] ACPI Error: No installed handler for fixed event [0x00000002] (20121018/evevent-284)
[  497.877404] Restarting tasks ... done.
[  497.881703] video LNXVIDEO:00: Restoring backlight state
[  497.953409] usb 2-1.6: new full-speed USB device number 5 using ehci-pci
[  498.040486] init: anacron main process (3439) killed by TERM signal
[  498.049521] usb 2-1.6: New USB device found, idVendor=8087, idProduct=07da
[  498.049525] usb 2-1.6: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[  498.052095] [drm] Enabling RC6 states: RC6 on, RC6p on, RC6pp off
[  498.095806] iwlwifi 0000:02:00.0: L1 Disabled; Enabling L0S
[  498.102376] iwlwifi 0000:02:00.0: Radio type=0x2-0x1-0x0
[  498.336600] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  504.844313] wlan0: authenticate with 00:15:f2:15:98:cc
[  504.852097] wlan0: send auth to 00:15:f2:15:98:cc (try 1/3)
[  504.856203] wlan0: authenticated
[  504.856523] iwlwifi 0000:02:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[  504.856534] iwlwifi 0000:02:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[  504.858991] wlan0: associate with 00:15:f2:15:98:cc (try 1/3)
[  504.861304] wlan0: RX AssocResp from 00:15:f2:15:98:cc (capab=0x411 status=0 aid=2)
[  504.863358] wlan0: associated
[  504.863420] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  506.956384] type=1400 audit(1378464360.272:32): apparmor="DENIED" operation="open" parent=1 profile="/usr/lib/telepathy/telepathy-*" name="/usr/share/p11-kit/modules/" pid=3646 comm="telepathy-gabbl" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 2481.584829] wlan0: deauthenticating from 00:15:f2:15:98:cc by local choice (reason=3)
[ 2481.614171] cfg80211: Calling CRDA to update world regulatory domain
[ 2481.623624] cfg80211: World regulatory domain updated:
[ 2481.623632] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 2481.623638] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 2481.623642] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 2481.623645] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 2481.623649] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 2481.623653] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 2482.809101] init: anacron main process (4304) killed by TERM signal
[ 2482.898802] PM: Syncing filesystems ... done.
[ 2484.508736] Freezing user space processes ... (elapsed 0.01 seconds) done.
[ 2484.523942] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
[ 2484.540231] Suspending console(s) (use no_console_suspend to debug)
[ 2484.540492] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 2484.542107] sd 0:0:0:0: [sda] Stopping disk
[ 2485.762008] PM: suspend of devices complete after 1223.488 msecs
[ 2485.762142] PM: late suspend of devices complete after 0.132 msecs
[ 2485.778059] ehci-pci 0000:00:1d.0: System wakeup enabled by ACPI
[ 2485.794047] ehci-pci 0000:00:1a.0: System wakeup enabled by ACPI
[ 2485.825897] xhci_hcd 0000:00:14.0: System wakeup enabled by ACPI
[ 2485.841880] PM: noirq suspend of devices complete after 79.855 msecs
[ 2485.842133] ACPI: Preparing to enter system sleep state S3
[ 2485.985867] PM: Saving platform NVS memory
[ 2486.039283] Disabling non-boot CPUs ...
[ 2486.141352] smpboot: CPU 1 is now offline
[ 2486.141796] Broke affinity for irq 46
[ 2486.245199] smpboot: CPU 2 is now offline
[ 2486.349042] smpboot: CPU 3 is now offline
[ 2486.349353] Extended CMOS year: 2000
[ 2486.350949] ACPI: Low-level resume complete
[ 2486.351006] PM: Restoring platform NVS memory
[ 2486.352919] Extended CMOS year: 2000
[ 2486.352999] Enabling non-boot CPUs ...
[ 2486.353086] smpboot: Booting Node 0 Processor 1 APIC 0x2
[ 2486.367059] CPU1 is up
[ 2486.367135] smpboot: Booting Node 0 Processor 2 APIC 0x1
[ 2486.381153] CPU2 is up
[ 2486.381206] smpboot: Booting Node 0 Processor 3 APIC 0x3
[ 2486.395082] CPU3 is up
[ 2486.402847] ACPI: Waking up from system sleep state S3
[ 2486.512451] xhci_hcd 0000:00:14.0: System wakeup disabled by ACPI
[ 2486.544392] ehci-pci 0000:00:1a.0: System wakeup disabled by ACPI
[ 2486.576345] ehci-pci 0000:00:1d.0: System wakeup disabled by ACPI
[ 2486.608446] PM: noirq resume of devices complete after 127.608 msecs
[ 2486.608568] PM: early resume of devices complete after 0.095 msecs
[ 2486.608593] i915 0000:00:02.0: setting latency timer to 64
[ 2486.608611] xhci_hcd 0000:00:14.0: setting latency timer to 64
[ 2486.608661] mei 0000:00:16.0: irq 45 for MSI/MSI-X
[ 2486.608682] ehci-pci 0000:00:1a.0: setting latency timer to 64
[ 2486.608750] ehci-pci 0000:00:1d.0: setting latency timer to 64
[ 2486.608760] snd_hda_intel 0000:00:1b.0: irq 47 for MSI/MSI-X
[ 2486.608776] ahci 0000:00:1f.2: setting latency timer to 64
[ 2486.832087] usb 2-1.6: reset full-speed USB device number 5 using ehci-pci
[ 2486.926689] btusb 2-1.6:1.0: no reset_resume for driver btusb?
[ 2486.926690] btusb 2-1.6:1.1: no reset_resume for driver btusb?
[ 2486.995843] usb 1-1.2: reset high-speed USB device number 3 using ehci-pci
[ 2487.159464] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 2487.159586] usb 2-1.5: reset high-speed USB device number 3 using ehci-pci
[ 2487.160663] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 2487.160926] ata1.00: ACPI cmd ef/10:06:00:00:00:a0 (SET FEATURES) succeeded
[ 2487.160928] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 2487.180707] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 2487.180886] ata1.00: ACPI cmd ef/10:06:00:00:00:a0 (SET FEATURES) succeeded
[ 2487.180888] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 2487.191275] ata1.00: configured for UDMA/133
[ 2487.207447] sd 0:0:0:0: [sda] Starting disk
[ 2487.349603] PM: resume of devices complete after 742.136 msecs
[ 2487.538895] Restarting tasks ... done.
[ 2487.550241] video LNXVIDEO:00: Restoring backlight state
[ 2487.684599] init: anacron main process (4583) killed by TERM signal
[ 2487.765453] iwlwifi 0000:02:00.0: L1 Disabled; Enabling L0S
[ 2487.772014] iwlwifi 0000:02:00.0: Radio type=0x2-0x1-0x0
[ 2487.898343] [drm] Enabling RC6 states: RC6 on, RC6p on, RC6pp off
[ 2488.007622] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2494.514319] wlan0: authenticate with 00:15:f2:15:98:cc
[ 2494.522311] wlan0: send auth to 00:15:f2:15:98:cc (try 1/3)
[ 2494.525777] wlan0: authenticated
[ 2494.526063] iwlwifi 0000:02:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 2494.526075] iwlwifi 0000:02:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 2494.528492] wlan0: associate with 00:15:f2:15:98:cc (try 1/3)
[ 2494.530873] wlan0: RX AssocResp from 00:15:f2:15:98:cc (capab=0x411 status=0 aid=2)
[ 2494.532960] wlan0: associated
[ 2494.533016] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 2496.335078] type=1400 audit(1378470391.992:33): apparmor="DENIED" operation="open" parent=1 profile="/usr/lib/telepathy/telepathy-*" name="/usr/share/p11-kit/modules/" pid=4842 comm="telepathy-gabbl" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 2723.856539] wlan0: deauthenticating from 00:15:f2:15:98:cc by local choice (reason=3)
[ 2723.875246] cfg80211: Calling CRDA to update world regulatory domain
[ 2723.886649] cfg80211: World regulatory domain updated:
[ 2723.886657] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 2723.886662] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 2723.886667] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 2723.886670] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 2723.886674] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 2723.886678] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 2725.075137] init: anacron main process (5056) killed by TERM signal
[ 2725.196921] PM: Syncing filesystems ... done.
[ 2726.799281] Freezing user space processes ... (elapsed 0.01 seconds) done.
[ 2726.814739] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
[ 2726.831011] Suspending console(s) (use no_console_suspend to debug)
[ 2726.831201] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 2726.832775] sd 0:0:0:0: [sda] Stopping disk
[ 2727.952390] PM: suspend of devices complete after 1123.502 msecs
[ 2727.952522] PM: late suspend of devices complete after 0.130 msecs
[ 2727.968435] ehci-pci 0000:00:1d.0: System wakeup enabled by ACPI
[ 2727.984413] ehci-pci 0000:00:1a.0: System wakeup enabled by ACPI
[ 2728.016245] xhci_hcd 0000:00:14.0: System wakeup enabled by ACPI
[ 2728.032221] PM: noirq suspend of devices complete after 79.856 msecs
[ 2728.032473] ACPI: Preparing to enter system sleep state S3
[ 2728.176137] PM: Saving platform NVS memory
[ 2728.228495] Disabling non-boot CPUs ...
[ 2728.331554] smpboot: CPU 1 is now offline
[ 2728.332004] Broke affinity for irq 46
[ 2728.435342] smpboot: CPU 2 is now offline
[ 2728.539146] smpboot: CPU 3 is now offline
[ 2728.539450] Extended CMOS year: 2000
[ 2728.541035] ACPI: Low-level resume complete
[ 2728.541092] PM: Restoring platform NVS memory
[ 2728.543013] Extended CMOS year: 2000
[ 2728.543093] Enabling non-boot CPUs ...
[ 2728.543181] smpboot: Booting Node 0 Processor 1 APIC 0x2
[ 2728.557162] CPU1 is up
[ 2728.557239] smpboot: Booting Node 0 Processor 2 APIC 0x1
[ 2728.571256] CPU2 is up
[ 2728.571314] smpboot: Booting Node 0 Processor 3 APIC 0x3
[ 2728.585197] CPU3 is up
[ 2728.592921] ACPI: Waking up from system sleep state S3
[ 2729.105653] xhci_hcd 0000:00:14.0: System wakeup disabled by ACPI
[ 2729.137580] ehci-pci 0000:00:1a.0: System wakeup disabled by ACPI
[ 2729.169516] ehci-pci 0000:00:1d.0: System wakeup disabled by ACPI
[ 2729.201600] PM: noirq resume of devices complete after 127.986 msecs
[ 2729.201727] PM: early resume of devices complete after 0.101 msecs
[ 2729.201771] i915 0000:00:02.0: setting latency timer to 64
[ 2729.201778] xhci_hcd 0000:00:14.0: setting latency timer to 64
[ 2729.201849] ehci-pci 0000:00:1a.0: setting latency timer to 64
[ 2729.201858] mei 0000:00:16.0: irq 45 for MSI/MSI-X
[ 2729.201914] ehci-pci 0000:00:1d.0: setting latency timer to 64
[ 2729.201939] snd_hda_intel 0000:00:1b.0: irq 47 for MSI/MSI-X
[ 2729.201950] ahci 0000:00:1f.2: setting latency timer to 64
[ 2729.295311] Extended CMOS year: 2000
[ 2729.425061] usb 2-1.5: reset high-speed USB device number 3 using ehci-pci
[ 2729.520792] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 2729.531068] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 2729.531262] ata1.00: ACPI cmd ef/10:06:00:00:00:a0 (SET FEATURES) succeeded
[ 2729.531264] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 2729.551028] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 2729.551218] ata1.00: ACPI cmd ef/10:06:00:00:00:a0 (SET FEATURES) succeeded
[ 2729.551236] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 2729.561664] ata1.00: configured for UDMA/133
[ 2729.576731] sd 0:0:0:0: [sda] Starting disk
[ 2729.588874] usb 1-1.2: reset high-speed USB device number 3 using ehci-pci
[ 2729.752501] usb 2-1.6: reset full-speed USB device number 5 using ehci-pci
[ 2729.846978] btusb 2-1.6:1.0: no reset_resume for driver btusb?
[ 2729.846980] btusb 2-1.6:1.1: no reset_resume for driver btusb?
[ 2729.847110] PM: resume of devices complete after 646.664 msecs
[ 2730.127309] Restarting tasks ... done.
[ 2730.132954] video LNXVIDEO:00: Restoring backlight state
[ 2730.355830] iwlwifi 0000:02:00.0: L1 Disabled; Enabling L0S
[ 2730.362400] iwlwifi 0000:02:00.0: Radio type=0x2-0x1-0x0
[ 2730.426963] [drm] Enabling RC6 states: RC6 on, RC6p on, RC6pp off
[ 2730.595541] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2737.031538] wlan0: authenticate with 00:15:f2:15:98:cc
[ 2737.037011] wlan0: send auth to 00:15:f2:15:98:cc (try 1/3)
[ 2737.039795] wlan0: authenticated
[ 2737.039901] iwlwifi 0000:02:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 2737.039903] iwlwifi 0000:02:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 2737.041789] wlan0: associate with 00:15:f2:15:98:cc (try 1/3)
[ 2737.044112] wlan0: RX AssocResp from 00:15:f2:15:98:cc (capab=0x411 status=0 aid=2)
[ 2737.047923] wlan0: associated
[ 2737.047948] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 2738.704583] type=1400 audit(1378477769.177:34): apparmor="DENIED" operation="open" parent=1 profile="/usr/lib/telepathy/telepathy-*" name="/usr/share/p11-kit/modules/" pid=5632 comm="telepathy-gabbl" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0