[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 3.8.0-1-linaro-arndale (buildd@gumiho) (gcc version 4.7.2 (Ubuntu/Linaro 4.7.2-2ubuntu1) ) #1ubuntu1~ci+130225052351-Ubuntu SMP PREEMPT Mon Feb 25 06:04:38 [ 0.000000] Kernel was built at commit id '' [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=30c7387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] Machine: SAMSUNG EXYNOS5 (Flattened Device Tree), model: SAMSUNG ARNDALE board based on EXYNOS5250 [ 0.000000] NR_BANKS too low, ignoring high memory [ 0.000000] Memory policy: ECC disabled, Data cache writealloc [ 0.000000] CPU EXYNOS5250 (id 0x43520020) [ 0.000000] exynos5_init_clocks: initializing clocks [ 0.000000] S3C24XX Clocks, Copyright 2004 Simtec Electronics [ 0.000000] exynos5_setup_clocks: registering clocks [ 0.000000] exynos5_setup_clocks: xtal is 24000000 [ 0.000000] EXYNOS5: PLL settings, A=1000000000, B=800000000, C=333000000 [ 0.000000] M=1600000000, E=96000000 V=300000000 [ 0.000000] EXYNOS5: ARMCLK=1000000000, CDREX=800000000, ACLK400=800000000 [ 0.000000] ACLK333=333000000, ACLK266=266666666, ACLK200=200000000 [ 0.000000] ACLK166=166500000, ACLK66=66666666 [ 0.000000] aclk_266_gscl: source is aclk_266 (1), rate is 266666666 [ 0.000000] sclk_g3d: source is mout_mpll_user (0), rate is 800000000 [ 0.000000] sclk_sata: source is mout_mpll_user (0), rate is 66666666 [ 0.000000] sclk_gscl_wrap: source is ext_xtal (0), rate is 24000000 [ 0.000000] sclk_gscl_wrap: source is ext_xtal (0), rate is 24000000 [ 0.000000] sclk_cam0: source is ext_xtal (0), rate is 24000000 [ 0.000000] sclk_cam1: source is ext_xtal (0), rate is 24000000 [ 0.000000] sclk_usbdrd30: source is mout_mpll (0), rate is 66666666 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x40000000-0x6f7fffff] [ 0.000000] HighMem [mem 0x6f800000-0xbfffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x40000000-0x6f7fffff] [ 0.000000] node 0: [mem 0x70000000-0xbfffffff] [ 0.000000] On node 0 totalpages: 522240 [ 0.000000] Normal zone: 1520 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 193040 pages, LIFO batch:31 [ 0.000000] HighMem zone: 2576 pages used for memmap [ 0.000000] HighMem zone: 325104 pages, LIFO batch:31 [ 0.000000] PERCPU: Embedded 9 pages/cpu @c1e0f000 s14400 r8192 d14272 u36864 [ 0.000000] pcpu-alloc: s14400 r8192 d14272 u36864 alloc=9*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 518144 [ 0.000000] Kernel command line: console=tty0 console=ttySAC2,115200n8 root=UUID=f6082041-6288-41a1-b540-3d7c7497c5e6 rootwait ro mac=02:75:4d:89:cd:33 [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] __ex_table already sorted, skipping sort [ 0.000000] Memory: 760MB 1280MB = 2040MB total [ 0.000000] Memory: 2055128k/2055128k available, 33832k reserved, 1310720K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc07d55d4 (7990 kB) [ 0.000000] .init : 0xc07d6000 - 0xc0824840 ( 315 kB) [ 0.000000] .data : 0xc0826000 - 0xc088e600 ( 418 kB) [ 0.000000] .bss : 0xc088e600 - 0xc0de66d4 (5473 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:549 [ 0.000000] Architected local timer running at 24.00MHz (phys). [ 0.000000] Switching to timer-based delay loop [ 0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] console [tty0] enabled [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.000000] ... MAX_LOCK_DEPTH: 48 [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 [ 0.000000] ... CLASSHASH_SIZE: 4096 [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.000000] ... CHAINHASH_SIZE: 16384 [ 0.000000] memory used by lock dependency info: 3695 kB [ 0.000000] per task-struct memory footprint: 1152 bytes [ 0.000000] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.000000] pid_max: default: 32768 minimum: 301 [ 0.000000] Security Framework initialized [ 0.000000] AppArmor: AppArmor initialized [ 0.000000] Mount-cache hash table entries: 512 [ 0.010000] CPU: Testing write buffer coherency: ok [ 0.010000] ftrace: allocating 19957 entries in 59 pages [ 0.040000] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.040000] Setting up static identity map for 0xc05bd0a0 - 0xc05bd0f8 [ 0.040000] Setting up static HYP identity map for 0xc05bd0f8 - 0xc05bd1c0 [ 0.100000] CPU1: Booted secondary processor [ 0.100000] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.100000] Brought up 2 CPUs [ 0.100000] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.100000] CPU: All CPU(s) started in HYP mode. [ 0.100000] CPU: Virtualization extensions available. [ 0.100000] devtmpfs: initialized [ 0.130000] pinctrl core: initialized pinctrl subsystem [ 0.150000] regulator-dummy: no parameters [ 0.150000] NET: Registered protocol family 16 [ 0.150000] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.170000] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.170000] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.170000] S3C Power Management, Copyright 2004 Simtec Electronics [ 0.170000] EXYNOS5250 PMU Initialize [ 0.170000] EXYNOS: Initializing architecture [ 0.210000] bio: create slab at 0 [ 0.210000] SCSI subsystem initialized [ 0.210000] libata version 3.00 loaded. [ 0.220000] usbcore: registered new interface driver usbfs [ 0.220000] usbcore: registered new interface driver hub [ 0.220000] usbcore: registered new device driver usb [ 0.220000] s3c-i2c s3c2440-i2c.0: slave address 0x66 [ 0.220000] s3c-i2c s3c2440-i2c.0: bus frequency set to 18 KHz [ 0.220000] sec_pmic 0-0066: No interrupt specified, no interrupts [ 0.300000] VDD_ALIVE_1.0V: 1100 mV [ 0.360000] VDD_28IO_DP_1.35V: 1200 mV [ 0.420000] VDD_COMMON1_1.8V: 1800 mV [ 0.480000] VDD_IOPERI_1.8V: 1800 mV [ 0.540000] VDD_EXT_1.8V: 1800 mV [ 0.600000] VDD_MPLL_1.1V: 1100 mV [ 0.660000] VDD_XPLL_1.1V: 1100 mV [ 0.720000] VDD_COMMON2_1.0V: 1000 mV [ 0.780000] VDD_33ON_3.0V: 3000 mV [ 0.840000] VDD_COMMON3_1.8V: 1800 mV [ 0.900000] VDD_ABB2_1.8V: 1800 mV [ 0.960000] VDD_USB_3.0V: 3000 mV [ 1.020000] VDDQ_C2C_W_1.8V: 1800 mV [ 1.080000] VDD18_ABB0/3_1.8V: 1800 mV [ 1.090000] VDD18_ABB0/3_1.8V: Failed to create debugfs directory [ 1.140000] VDD10_COMMON4_1.0V: 1000 mV [ 1.200000] VDD18_HSIC_1.8V: 1800 mV [ 1.260000] VDDQ_MMC2/3_2.8V: 2800 mV [ 1.270000] VDDQ_MMC2/3_2.8V: Failed to create debugfs directory [ 1.320000] VDD_33ON_2.8V: 2800 mV [ 1.350000] VDD_MIF_1.2V: 950 <--> 1200 mV at 1000 mV [ 1.380000] vdd_arm: 925 <--> 1300 mV at 1075 mV [ 1.410000] VDD_INT_1.0V: 900 <--> 1200 mV at 1000 mV [ 1.470000] VDD_G3D_1.0V: 1000 mV [ 1.500000] VDD_MEM_1.35V: 750 <--> 1350 mV at 1200 mV [ 1.510000] s3c-i2c s3c2440-i2c.0: i2c-0: S3C I2C adapter [ 1.510000] s3c-i2c s3c2440-hdmiphy-i2c: slave address 0x00 [ 1.510000] s3c-i2c s3c2440-hdmiphy-i2c: bus frequency set to 65 KHz [ 1.510000] s3c-i2c s3c2440-hdmiphy-i2c: i2c-1: S3C I2C adapter [ 1.510000] s3c-i2c exynos5-sata-phy-i2c: slave address 0x38 [ 1.510000] s3c-i2c exynos5-sata-phy-i2c: bus frequency set to 39 KHz [ 1.510000] s3c-i2c exynos5-sata-phy-i2c: i2c-2: S3C I2C adapter [ 1.510000] NetLabel: Initializing [ 1.510000] NetLabel: domain hash size = 128 [ 1.510000] NetLabel: protocols = UNLABELED CIPSOv4 [ 1.510000] NetLabel: unlabeled traffic allowed by default [ 1.510000] Switching to clocksource mct-frc [ 1.570000] AppArmor: AppArmor Filesystem Enabled [ 1.600000] NET: Registered protocol family 2 [ 1.600000] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 1.600000] TCP bind hash table entries: 8192 (order: 6, 294912 bytes) [ 1.600000] TCP: Hash tables configured (established 8192 bind 8192) [ 1.600000] TCP: reno registered [ 1.600000] UDP hash table entries: 512 (order: 3, 40960 bytes) [ 1.600000] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes) [ 1.600000] NET: Registered protocol family 1 [ 1.610000] Trying to unpack rootfs image as initramfs... [ 1.730000] Freeing initrd memory: 2180K [ 1.730000] kvm [1]: interrupt-controller@10484000 IRQ25 [ 1.730000] kvm [1]: timer IRQ27 [ 1.730000] kvm [1]: Hyp mode initialized successfully [ 1.740000] hw perfevents: enabled with ARMv7_Cortex_A15 PMU driver, 7 counters available [ 1.740000] audit: initializing netlink socket (disabled) [ 1.740000] type=2000 audit(1.740:1): initialized [ 1.740000] bounce pool size: 64 pages [ 1.740000] VFS: Disk quotas dquot_6.5.2 [ 1.740000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.740000] jffs2: version 2.2. (NAND) (SUMMARY) \xffffffc2\xffffffa9 2001-2006 Red Hat, Inc. [ 1.750000] Btrfs loaded [ 1.750000] msgmni has been set to 1458 [ 1.750000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) [ 1.750000] io scheduler noop registered [ 1.750000] io scheduler deadline registered [ 1.750000] io scheduler cfq registered (default) [ 1.770000] dma-pl330 dma-pl330.0: Loaded driver for PL330 DMAC-2364208 [ 1.770000] dma-pl330 dma-pl330.0: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.780000] dma-pl330 dma-pl330.1: Loaded driver for PL330 DMAC-2364208 [ 1.780000] dma-pl330 dma-pl330.1: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.780000] dma-pl330 dma-pl330.2: Loaded driver for PL330 DMAC-2364208 [ 1.780000] dma-pl330 dma-pl330.2: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.990000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 2.000000] exynos4210-uart.0: ttySAC0 at MMIO 0x12c00000 (irq = 83) is a S3C6400/10 [ 2.000000] exynos4210-uart.1: ttySAC1 at MMIO 0x12c10000 (irq = 84) is a S3C6400/10 [ 2.000000] exynos4210-uart.2: ttySAC2 at MMIO 0x12c20000 (irq = 85) is a S3C6400/10 [ 2.940000] console [ttySAC2] enabled [ 2.940000] exynos4210-uart.3: ttySAC3 at MMIO 0x12c30000 (irq = 86) is a S3C6400/10 [ 2.970000] brd: module loaded [ 2.980000] loop: module loaded [ 2.980000] ahci-sata exynos5-sata: failed to get sata phy [ 2.990000] platform exynos5-sata: Driver ahci-sata requests probe deferral [ 3.000000] mtdoops: mtd device (mtddev=name/number) must be supplied [ 3.000000] Synopsys Designware Multimedia Card Interface Driver [ 3.010000] dwmmc_exynos dw_mmc.0: Using internal DMA controller. [ 3.020000] dwmmc_exynos dw_mmc.0: DW MMC controller at irq 107, 32 bit host data width, 128 deep fifo [ 3.030000] dwmmc_exynos dw_mmc.0: wp gpio not available [ 3.030000] mmc0: no vmmc regulator found [ 3.060000] mmc_host mmc0: Bus speed (slot 0) = 100000000Hz (slot req 400000Hz, actual 400000HZ div = 125) [ 3.080000] dwmmc_exynos dw_mmc.0: 1 slots initialized [ 3.080000] dwmmc_exynos dw_mmc.0: Version ID is 241a [ 3.080000] dwmmc_exynos dw_mmc.2: Using internal DMA controller. [ 3.090000] dwmmc_exynos dw_mmc.2: DW MMC controller at irq 109, 32 bit host data width, 128 deep fifo [ 3.100000] dwmmc_exynos dw_mmc.2: wp gpio not available [ 3.100000] mmc1: no vmmc regulator found [ 3.130000] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 400000Hz, actual 400000HZ div = 125) [ 3.150000] dwmmc_exynos dw_mmc.2: 1 slots initialized [ 3.150000] dwmmc_exynos dw_mmc.2: Version ID is 241a [ 3.160000] usbcore: registered new interface driver asix [ 3.160000] usbcore: registered new interface driver cdc_ether [ 3.170000] usbcore: registered new interface driver dm9601 [ 3.170000] usbcore: registered new interface driver net1080 [ 3.180000] usbcore: registered new interface driver cdc_subset [ 3.180000] mmc0: BKOPS_EN bit is not set [ 3.190000] usbcore: registered new interface driver zaurus [ 3.190000] usbcore: registered new interface driver MOSCHIP usb-ethernet driver [ 3.200000] usbcore: registered new interface driver cdc_ncm [ 3.210000] mmc_host mmc0: Bus speed (slot 0) = 100000000Hz (slot req 52000000Hz, actual 50000000HZ div = 1) [ 3.220000] mmc0: new high speed DDR MMC card at address 0001 [ 3.220000] mmcblk0: mmc0:0001 M4G1FA 3.72 GiB [ 3.230000] mmcblk0boot0: mmc0:0001 M4G1FA partition 1 1.00 MiB [ 3.230000] mmcblk0boot1: mmc0:0001 M4G1FA partition 2 1.00 MiB [ 3.240000] mmcblk0rpmb: mmc0:0001 M4G1FA partition 3 128 KiB [ 3.250000] mmcblk0: p1 p2 p3 p4 [ 3.260000] mmcblk0boot1: unknown partition table [ 3.270000] mmcblk0boot0: unknown partition table [ 3.340000] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 50000000Hz, actual 50000000HZ div = 1) [ 3.350000] mmc1: new high speed SDHC card at address e624 [ 3.360000] mmcblk1: mmc1:e624 SU04G 3.69 GiB [ 3.370000] mmcblk1: p1 p2 p3 [ 3.410000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.420000] exynos5250-usbphy s3c-usbphy: Already power on PHY [ 3.420000] s5p-ehci s5p-ehci: S5P EHCI Host Controller [ 3.430000] s5p-ehci s5p-ehci: new USB bus registered, assigned bus number 1 [ 3.430000] s5p-ehci s5p-ehci: irq 103, io mem 0x12110000 [ 3.460000] s5p-ehci s5p-ehci: USB 2.0 started, EHCI 1.00 [ 3.460000] usb usb1: Product: S5P EHCI Host Controller [ 3.460000] usb usb1: Manufacturer: Linux 3.8.0-1-linaro-arndale ehci_hcd [ 3.470000] usb usb1: SerialNumber: s5p-ehci [ 3.480000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.480000] exynos5250-usbphy s3c-usbphy: Already power on PHY [ 3.490000] exynos-ohci exynos-ohci: EXYNOS OHCI Host Controller [ 3.500000] exynos-ohci exynos-ohci: new USB bus registered, assigned bus number 2 [ 3.500000] exynos-ohci exynos-ohci: irq 103, io mem 0x12120000 [ 3.570000] usb usb2: Product: EXYNOS OHCI Host Controller [ 3.570000] usb usb2: Manufacturer: Linux 3.8.0-1-linaro-arndale ohci_hcd [ 3.580000] usb usb2: SerialNumber: exynos-ohci [ 3.590000] xhci-hcd xhci-hcd: xHCI Host Controller [ 3.590000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 3 [ 3.600000] xhci-hcd xhci-hcd: irq 104, io mem 0x12000000 [ 3.600000] usb usb3: Product: xHCI Host Controller [ 3.610000] usb usb3: Manufacturer: Linux 3.8.0-1-linaro-arndale xhci-hcd [ 3.610000] usb usb3: SerialNumber: xhci-hcd [ 3.620000] xHCI xhci_add_endpoint called for root hub [ 3.620000] xHCI xhci_check_bandwidth called for root hub [ 3.620000] xhci-hcd xhci-hcd: xHCI Host Controller [ 3.620000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 4 [ 3.630000] usb usb4: Product: xHCI Host Controller [ 3.640000] usb usb4: Manufacturer: Linux 3.8.0-1-linaro-arndale xhci-hcd [ 3.640000] usb usb4: SerialNumber: xhci-hcd [ 3.650000] xHCI xhci_add_endpoint called for root hub [ 3.650000] xHCI xhci_check_bandwidth called for root hub [ 3.650000] Initializing USB Mass Storage driver... [ 3.650000] usbcore: registered new interface driver usb-storage [ 3.660000] USB Mass Storage support registered. [ 3.660000] mousedev: PS/2 mouse device common for all mice [ 3.670000] Exynos: Kernel Thermal management registered [ 3.680000] device-mapper: ioctl: 4.23.1-ioctl (2012-12-18) initialised: dm-devel@redhat.com [ 3.680000] cpuidle: using governor ladder [ 3.690000] cpuidle: using governor menu [ 3.690000] usbcore: registered new interface driver usbhid [ 3.700000] usbhid: USB HID core driver [ 3.700000] oprofile: using timer interrupt. [ 3.710000] TCP: cubic registered [ 3.710000] Initializing XFRM netlink socket [ 3.710000] NET: Registered protocol family 10 [ 3.720000] sit: IPv6 over IPv4 tunneling driver [ 3.730000] NET: Registered protocol family 17 [ 3.730000] NET: Registered protocol family 15 [ 3.730000] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 3.740000] Registering SWP/SWPB emulation handler [ 3.750000] ahci-sata exynos5-sata: forcing PORTS_IMPL to 0x1 [ 3.750000] ahci-sata exynos5-sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 3.760000] ahci-sata exynos5-sata: flags: ncq sntf pm led clo only pmp pio slum part ccc apst [ 3.770000] scsi0 : ahci_platform [ 3.780000] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 147 [ 4.140000] ata1: SATA link down (SStatus 0 SControl 300) [ 4.140000] Freeing init memory: 312K [ 4.350000] usb 1-3.2: Product: USB2.0 Hub [ 4.760000] usb 1-3.2.3: Product: DT 101 G2 [ 4.760000] usb 1-3.2.3: Manufacturer: Kingston [ 4.770000] usb 1-3.2.3: SerialNumber: 001E4FECA802ED2027640065 [ 4.780000] scsi1 : usb-storage 1-3.2.3:1.0 [ 4.820000] udevd[1162]: starting version 175 [ 4.980000] usb 1-3.2.4: Product: AX88772 [ 4.980000] usb 1-3.2.4: Manufacturer: ASIX Elec. Corp. [ 5.010000] usb 1-3.2.4: SerialNumber: 000001 [ 5.380000] asix 1-3.2.4:1.0 eth0: register 'asix' at usb-s5p-ehci-3.2.4, ASIX AX88772 USB 2.0 Ethernet, 02:75:4d:89:cd:33 [ 5.480000] EXT4-fs (mmcblk1p3): mounted filesystem with ordered data mode. Opts: (null) [ 5.800000] scsi 1:0:0:0: Direct-Access Kingston DT 101 G2 PMAP PQ: 0 ANSI: 4 [ 5.810000] sd 1:0:0:0: Attached scsi generic sg0 type 0 [ 5.820000] sd 1:0:0:0: [sda] 15240576 512-byte logical blocks: (7.80 GB/7.26 GiB) [ 5.830000] sd 1:0:0:0: [sda] Write Protect is off [ 5.840000] sd 1:0:0:0: [sda] Mode Sense: 23 00 00 00 [ 5.840000] sd 1:0:0:0: [sda] No Caching mode page present [ 5.840000] sd 1:0:0:0: [sda] Assuming drive cache: write through [ 5.870000] sd 1:0:0:0: [sda] No Caching mode page present [ 5.870000] sd 1:0:0:0: [sda] Assuming drive cache: write through [ 5.880000] sda: sda1 [ 5.900000] sd 1:0:0:0: [sda] No Caching mode page present [ 5.900000] sd 1:0:0:0: [sda] Assuming drive cache: write through [ 5.910000] sd 1:0:0:0: [sda] Attached SCSI removable disk [ 6.380000] init: plymouth main process (1272) killed by SEGV signal [ 6.400000] init: ureadahead main process (1271) terminated with status 5 [ 7.050000] EXT4-fs (mmcblk1p3): re-mounted. Opts: errors=remount-ro [ 8.350000] udevd[1361]: starting version 175 [ 9.690000] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 10.180000] init: plymouth-log main process (1561) terminated with status 1 [ 10.240000] init: udev-fallback-graphics main process (1575) terminated with status 1 [ 10.400000] init: plymouth-upstart-bridge main process (1596) terminated with status 1 [ 10.860000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 10.870000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 10.870000] asix 1-3.2.4:1.0 eth0: link down [ 12.660000] asix 1-3.2.4:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xC1E1 [ 17.060000] init: failsafe main process (1564) killed by TERM signal [ 17.680000] type=1400 audit(17.676:2): apparmor="STATUS" operation="profile_load" name="/usr/sbin/mysqld" pid=1692 comm="apparmor_parser" [ 17.940000] type=1400 audit(17.936:3): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=1691 comm="apparmor_parser" [ 17.940000] type=1400 audit(17.936:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1691 comm="apparmor_parser" [ 17.940000] type=1400 audit(17.936:5): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=1691 comm="apparmor_parser" [ 18.120000] type=1400 audit(18.116:6): apparmor="STATUS" operation="profile_load" name="/usr/sbin/tcpdump" pid=1694 comm="apparmor_parser" [ 20.200000] type=1400 audit(20.196:7): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/mysqld" pid=1771 comm="apparmor_parser" [ 23.680000] init: plymouth-stop pre-start process (1928) terminated with status 1 [ 23.700000] init: tty1 main process (1929) killed by TERM signal